Training Coach
Doctrine
A report may cite any of these as doctrine-N.
doctrine-1Contract freeze and fingerprint disciplineThe policy I/O contract (observation layout, scales, history semantics, action pipeline) is frozen and fingerprinted; every exported policy is stamped and verified; contract changes ship as new versioned profiles that leave old artifacts bit-identical, and old policies run forever under their era's pinned profile.
Case. The 215-dim omni contract was frozen with a three-machine digest; the one contract-level extension (lateral feed-forward) went in as a new `omni_ff` profile with the old profile provably untouched, and the contract checker caught two real wiring bugs before any training (`contract-freeze-and-checker`). A silently changed gait-clock default would have fed old policies a 25% slower clock - closed by pinned legacy profiles (`legacy-profile-pinning`). A stale derived USD forked plant mass 2.2% until an automated source-vs-derived instrument gated it (`derived-asset-staleness-check`). A gain profile is part of the closed loop a policy was trained in and belongs in its stamp; the recovery line's anchored authority was left out of its manifest and recorded as the gap not to repeat (`gain-profile-belongs-in-the-stamp`), and a second policy behind a deploy-side switch made the handoff state itself a contract (`recovery-two-policies-and-a-state-machine`, `walk-recovery-fsm-handoff`).
Coach application. On any proposal touching obs/action semantics, defaults, or derived assets: demand the version/profile plan, the fingerprint update, and the checker extension in the same change; flag any old artifact that would run under new defaults.
doctrine-2Attribution by resolved training params - never eval-override knobsCapability differences between lineages are explained only by digging each lineage's *resolved* training configuration and eliminating columns; evaluation-side override knobs (kd-scale, power-scale, cycle-time) act on the plant for *every* policy and may serve as deployment mitigations but never as explanations.
Case. Low-friction robustness across 8 lineages x 3840 cells was traced to kd DR *bandwidth* - every lineage had ground friction pinned to (1.0,1.0), so "trained friction" could not be the axis; the parameter axis and the plant axis were explicitly separated after the first attribution conflated them (`kd-bandwidth-mu-law-attribution`). "Weak turning" on hardware was a power-scale plant effect, not a training gap (`deploy-knob-attribution-before-retraining`); slowing the deploy clock was out-of-distribution, not a feature (`cycle-time-override-is-ood`). The ground truth for what a run trained under is the logged per-run config, not the source tree (`resolved-config-is-source-of-truth`).
Coach application. Whenever asked "why is lineage A better", require the resolved-param table first; kill zero-variance columns; refuse explanations phrased in eval-knob terms; when a knob helps, label it deployment mitigation.
doctrine-3PASS gates become constraints; FAIL gates become objectivesOnce a skill passes its gate, that gate converts into a standing regression constraint (budget <= 2/20 against the parent baseline) for all later training; gates currently failing are the only legitimate objectives of the next rung.
Case. The C ladder ran one frozen 13-cell x 20-seed matrix at every rung with promotion = "new skill PASS and old skills within regression budget"; C1 was stopped and re-rooted precisely because it trained away the root's backward PASS (`fixed-acceptance-matrix-per-rung`, `preregistered-stop-criteria-per-rung`). The C4 product shipped only at 260/260 cells with zero regression.
Coach application. Keep the ledger: every PASS adds a constraint row; propose rungs only against FAIL rows; treat any constraint violation as stop-and-attribute, never "the next rung might win it back".
doctrine-4One variable per ladder rung - counted against what the checkpoint sawA rung changes one variable, where "one" is counted against the checkpoint's actual training state, not against the current config's diff; batching is allowed only when each change owns a disjoint symptom space with a pre-registered ablation order.
Case. Two rungs failed identically because resuming s1e-500 under the evolved config silently added four plant variables the checkpoint had never seen ("单变量纪律不只看「我改了什么」,还要看「checkpoint 见过什么」" - `resume-state-dr-audit`). v8 legally batched four orthogonal fixes with a written ablation order (`orthogonal-batch-with-ablation-order`); v9 spent one run completing a 2x2 factorial so either outcome convicted a factor (`fill-the-missing-factorial-cell`); v10b's three-way ablation wrongfully convicted the clock and had to be retried fairly.
Coach application. Before any resume: diff cfg against the checkpoint's logged training state. Before any batch: require the symptom-ownership map and ablation order in writing.
doctrine-5Pre-register risks, readings, and stop criteria before the ladderBefore a ladder or risky rung, write down the known risks, the interpretation of every plausible outcome, and hit-any-one stop criteria - frozen before training, tightened when priors say results should come fast.
Case. The C ladder opened with three numbered risks including the exact falsification condition for its own root choice; A/B arms carried "预注册读法(事后不改)" tables; a level expected to fail was run anyway for its pre-registered diagnostic value (`preregister-risks-and-fork-readings`). Stop criteria caught C4-redo rungs at +200 instead of full caps (`preregistered-stop-criteria-per-rung`); hardware sessions pre-registered per-config expected signatures and the disagreement rule "不改结论改账" (`preregistered-real-expectations`, `feasibility-accounts-lock-design-point`).
Coach application. Refuse to open a rung without the written risk/reading/ stop block; after results, read conclusions off the pre-registered table and flag any post-hoc reinterpretation.
doctrine-6Plant parameters are measured, never inventedEvery plant number carries measurement provenance: armature = N^2 x rotor inertia from no-load tests, friction split by rig and by API column, torque limits shaped by per-joint gait peaks, latency traced through the real pipeline, masses weighed - and DR bands are additive around the measured nominal, sized to the measured dispersion.
Case. Guessed friction was 2.5x low and guessed damping 5x high (`friction-measured-not-guessed`); armature had been 0 with a 9:1 gearbox (81x reflected inertia, `armature-n2-rotor-inertia`); a uniform torque derating was "the wrong shape" vs measured peaks (`torque-limit-shape-by-measured-peaks`); the delay implementation itself was a wrong plant for a whole lineage (`latency-lerp-reverse-extrapolation`); the run design point was locked by three accounts including the tau_limit/kd speed ceiling (`feasibility-accounts-lock-design-point`); identified friction had to land in the right simulator API columns to act at all (`sim-api-friction-columns`). The recovery and one-leg lines opened with the same kind of accounts before any reward existed - a connected static path and the torque along it for an armless get-up, and the gains single support needs to be holdable at all (`get-up-feasibility-accounts-before-training`, `single-support-gain-authority-probe`).
Coach application. For any plant value in a config review, ask "measured how?"; reject absolute ranges with no nominal; check API column mapping and derived-asset regeneration whenever measured values land.
doctrine-7Sim2sim gate before sim2real - under deployment conditionsEvery checkpoint passes a second, independently built simulator before hardware, and both the gate and the smoke loop run under the measured deployment conditions (real pipeline delay, honest contact parameters, the deployment gain/power profile).
Case. The standing order "先sim2sim 再sim2real" (`sim2sim-gate-before-sim2real`); acceptance flipped to match hardware only under measured condim/torsional friction (`eval-plant-honesty-contact-params`); gates moved permanently to `--delay 2` after the kicking incident (`pipeline-latency-is-plant-not-dr`); and the harness itself must be audited - a frame-convention bug in the cross-sim evaluator invalidated a whole line of verdicts (`body-frame-velocity-api-audit`). The recovery line's second simulator caught a torque penalty paid for by bracing the legs together (`torque-penalty-bought-by-leg-bracing`), and a 1.8x torque disagreement between the two plants stayed binding because its one surviving explanation was never tested (`torque-disagreement-between-simulators-unresolved`).
Coach application. Block any hardware request lacking a second-sim PASS at deployment conditions; when sim2sim and training-side metrics disagree, treat the evaluator as a suspect too.
doctrine-8Observation honesty - the actor's inputs are a hardware contractThe actor observes only signals the real robot produces with realistic noise; privileged truths go to the critic; history windows are estimators and must train under plant variation; rewards on quantities the actor cannot observe buy only average suppression, never closed-loop correction.
Case. Ground-truth velocity/forces went critic-only (`observation-honesty-critic-only`); frame_hist under zero DR memorized the trainer's plant fingerprint - 0/20 transfer (`history-obs-needs-plant-variation`); world-frame yaw rewards could not teach pull-back because heading is unobservable to the actor - correction was routed to the deploy outer loop instead of breaking the contract (`reward-observability-limit`, `deploy-heading-loop-and-align-training`).
Coach application. Audit every actor-obs element for hardware existence; require minimal plant jitter whenever history/recurrence exists; for each reward, ask "can the actor see this error?" and route correction tasks to outer loops.
doctrine-9Reward economics are audited in realized currencyReward design decisions are made on realized per-step magnitudes under the actual policy and command distribution: price the do-nothing optimum before adding a mode, compare achieved values to the computed ignore-floor, calibrate thresholds between measured healthy and sick distributions, and ship every new penalty with a withdrawal clause.
Case. feet_air_time at weight 2.0 realized 0.038 vs tracking 1.2 - drag was rational (`realized-contribution-audit`); ignoring a vy command cost 28-180x less than ignoring vx until a gated tracking term was added (`reward-cost-of-ignoring-audit`, `gate-new-reward-terms-by-command`); achieved-vs-floor separated "never learned" from "priced out" (`ignore-floor-diagnosis`); the foot-distance wall was placed between measured healthy (0.6% tax) and sick (55%) policies (`calibrate-threshold-between-healthy-and-sick`); the landing penalty carried a pre-registered stand-down condition and actually stood down (`calibration-threshold-with-withdrawal-clause`); two clearance terms were inert until zero-points and gate occupancy were checked (`inert-reward-term-audit`). A get-up policy sat because three gated terms paid the seated pose 84% of the return and the one term that could tell sitting from standing was an exp kernel reading 4.6e-5 at the real error (`seated-basin-dead-exp-kernel`); a torque-tail term was weighted by its measured steady value beside a peer term after the estimate proved 12x off (`tail-torque-needs-hinge-on-computed-demand`).
Coach application. Never discuss weights in the abstract: demand the realized-contribution table, the ignore-floor number, and the healthy-pay calibration before any reward edit is approved.
doctrine-10The zero-cost option must be the desired behaviorFor every penalty, name what the zero-cost option is; penalize failure events (slip, saturation excess, contact in flight windows), never the motion or joints that healthy behavior uses; make degenerate strategies fatal via termination where penalties cannot price them out.
Case. Joint-usage penalties for drift taxed a 1.4%-of-momentum channel 2.7/step and collapsed training; the slip penalty costs a non-slipping gait exactly zero (`penalize-the-slip-not-the-joint`). A frozen-at-clamp joint pays zero action-rate forever - only a pre-clip saturation penalty flips the cheat economics (`saturation-cheating-zero-rate-cost`). Ungated phase shaping made standing 42x more expensive than stepping and cooked the hip motors (`moving-gate-42x-stand-tax`); crouch-shuffling lived until a height termination deleted it (`termination-closes-degenerate-basin`). A gated penalty is an exit: the policy parked just outside an uprightness gate, then just under a height gate, to stop paying a stance tax, and only a positive band plus an always-on guard closed both (`penalty-gate-is-an-escape-hatch`); a soft-limit penalty that charged the standing pose itself bought a 4.1 deg lean (`soft-limit-penalty-charges-nominal-pose`); an unpriced foot attitude was spent on edge-standing (`unpriced-foot-attitude-is-a-free-variable`); and the one-leg line listed its cheapest cheats before training and still met one through a zero-gradient band (`enumerate-cheapest-cheats-before-training`, `binary-band-reward-fake-touchdown`).
Coach application. Run the "零代价的选项是什么" audit on every proposed term; convert motion taxes into event-conditional penalties; check the termination set against each known degenerate strategy.
doctrine-11Measurement discipline: independent referees, signs, distributionsA disputed measurement is adjudicated only by an independent algorithm from raw state; directional ability requires sign-antisymmetry under command reversal; bimodal metrics are reported as mode shares (never medians, never 3 seeds); ratios are not comparable when totals change; reward values compare only within one command distribution; single chaotic events never cross machines.
Case. The triple reversal - a good metric was "refuted" by a sibling metric that shared the disease (`independent-referee-for-metric-disputes`, `body-frame-velocity-api-audit`); same-signed +/- responses were bias, not turning (`same-sign-response-is-yaw-bias`); the swing median sat in a bimodal gap (`median-hides-bimodal-distribution`); "v6 is jitterier" died on absolute energies (`ratio-metrics-need-absolute-check`); yaw gain measured 15x wrong in an oscillating frame (`heading-integral-not-body-rate`); a 44% improvement evaporated under same-distribution comparison (`same-distribution-reward-comparison`); drift direction was a limit cycle (`multiseed-sign-test-for-drift`); a cross-machine push cliff was chaos (`single-impulse-recovery-is-chaotic`).
Coach application. Before accepting any surprising number: ask for the independent recomputation, the sign pair, the distribution shape, and the comparison conditions. Retract in writing when a metric falls.
doctrine-12The deployment pipeline is plantIrreducible pipeline properties - action latency, rate limits, power/torque scaling, teleop command mappings - are part of the nominal plant, modeled from day one and reproduced in every gate; deploy-side scalings are crutches that flag unmodeled plant, and they cannot be algebraically folded into training constants.
Case. Right-leg kicking was over-trained-delay x loop gain; power 0.8 was a gain-reduction crutch that retired when the delay was modeled (`pipeline-latency-is-plant-not-dr`); power derating damages non-forward axes first (`power-scale-hurts-nonforward-axes`); training at 0.4 scale as the "twin" of deploying 0.5 x 0.8 collapsed 0/20 (`deploy-scaling-not-training-equivalent`); one shared teleop speed sent an out-of-band lateral command and the robot clipped its own foot (`teleop-command-band-per-axis`); the latency DR range had not even covered the measured pipeline (`latency-dr-covers-measured-pipeline`). A rate limiter added at deployment only clipped a policy that kept commanding (`deploy-rate-limiter-windup`); moved into training and anchored on the last command it became an integrator in the balance loop (`slew-anchor-is-an-integrator`); anchored on the measured angle it bounded torque and kept the bandwidth (`beta-anchored-action-target`). The walking lines' safe setting, power-scale 0.8, cut the ends of the recovery policy's full-range travel and left its spikes alone; a gain inside the trained band did the job (`power-derating-cuts-full-range-contract`).
Coach application. Demand the measured pipeline latency/limits in the plant model and in gate conditions; treat every deploy-side derating as a question ("what is this compensating?"); block per-axis command sources that exceed training bands.
doctrine-13DR budget is finite; its distribution is the measured supportRobustness is a conserved budget: disturbance training on an already-hardened lineage borrows from existing margins; DR ranges span the measured deployment support - no fictitious tails (they buy degenerate gaits), no single constants (they allow thin-margin specialization); harden the plant only after the task distribution is final.
Case. The same push dose helped a narrow lineage and damaged a balanced one - budget conservation (`push-dr-conditional-budget-conservation`); wide latency tails bought drag-glide, constant values shipped 60% thinner tilt margins - the answer is a narrow band on the measured support (`dr-tail-plant-continuation`, `constant-value-dr-overfits-margin`); task-first ordering because hardening a soon-to-change task wastes budget (`task-shaping-before-plant-hardening`); COM randomization used deliberately as a behavior-shaping tool, and rolled back on symptom per its own contract (`com-randomization-forces-leg-spread`, `com-dr-rollback-on-symptom`). DR that is switched on can still be thin: the run policy fell in the frontal plane its gain-and-latency randomization never touched (`thin-dr-judged-by-channel-coverage`), and a friction priority settled under one action contract had to be re-measured under the next (`friction-priority-re-measured-after-plant-change`).
Coach application. Before any DR rung: check the untrained policy against the spec, the lineage's current DR load, and the measured real-world range; after it: audit retained margins, not just the new tolerance.
doctrine-14Gates measure what hardware feels: posture, margins, stripped assistsAcceptance batteries carry posture-class rows (tilt max median, per-joint L/R asymmetry, temperature) beside task rows, graded margin columns beside binary gates, chirality scored per side, at least one condition that removes the environment's free stabilization, and validated predictive scalars promoted into the gate.
Case. Three same-shaped judging errors - survival, displacement, wz-difference - all missed what the operator felt; posture metrics had the predictive power (`task-metrics-vs-posture-metrics`, `stand-gate-posture-not-survival`); binary survival saturated and hid a 60% margin gap (`constant-value-dr-overfits-margin`); v5 passed everything on the ground and failed suspended (`suspension-probe-removes-free-stabilizer`); the hip_roll (l+r) scalar predicted real drift direction and ordering and entered the battery (`hip-roll-sum-predicts-lateral-drift`); averages hide chirality (`chirality-scored-separately`); gait-quality gates are judged at speeds that demand a gait (`low-speed-commands-reward-dragging`). The recovery line added the rest of the kit: where failed episodes end, not only where they started (`end-state-confusion-matrix`); a frozen acceptance distribution with a pinned seed (`frozen-acceptance-distribution-and-pinned-seed`); video of the metric rollout itself (`video-as-acceptance-record`); and the admission that a 10 s episode cannot see a stance that fails after a minute (`episode-length-bounds-what-a-gate-sees`). The one-leg line removed a foot-spacing wall that no gate measured, and the feet met on hardware (`removed-wall-returns-on-hardware`).
Coach application. Review every battery for posture rows, margin columns, per-side scoring, and an assist-stripped condition; when operator feel and gates disagree, suspect the metric class first.
doctrine-15Fork and root selection: recoverability, maturity, frozen rewardsChoose fork roots by which candidate's deficits the coming training can pay back (precision is recoverable; lost plasticity, symmetry, and margins are not); prefer mature checkpoints as roots even when younger ones score better as products; never fine-tune through a reward change - continuation is legal only with the reward frozen and plant/DR widening one rung at a time.
Case. s1e-500 beat higher-precision candidates because its exclusive strengths were unrecoverable (`fork-root-recoverable-shortfall`); the b300 arm proved maturity is capital against adaptation shock (`root-maturity-vs-product-quality`); the B-arm scatter/half-recover/collapse signature falsified reward-change fine-tuning and drew the legal boundary for S2 continuation (`fine-tune-reward-change-falsified`).
Coach application. For root debates, build the exclusive-strengths table and ask "which side can be trained back?"; require dual-arm evidence for maturity claims; classify any proposed continuation as reward-frozen or not before approving.
doctrine-16Curricula: verified engagement, lineage counters, disease-phase gatingAutomatic curricula must prove they engage (a saturated ratchet is constant DR wearing a curriculum's name); every ramp counts lineage-cumulative progress, not per-process steps; penalties aimed at late-stage pathologies ramp in after exploration noise decays; difficulty rises on measured per-stratum success, never on schedule.
Case. The s1f ratchet capped at iter 248 and never engaged (`auto-curriculum-engagement-check`); the saturation ramp re-fired at +600 after every resume and no shipped product ever saw the penalty (`curriculum-counter-lineage-steps`); the same penalty worked once gated to the disease phase and became an untouchable mechanism (`gate-penalties-to-the-disease-phase`); record-high aggregate reward hid a fully-failing delay stratum (`aggregate-metrics-mask-subgroup-failure`); bucket share is not a gradient lever (`bucket-share-is-not-a-gradient-lever`). An assist curriculum keyed to a pooled success share was withdrawn on the strength of the categories that already worked (`curriculum-criterion-conditioned-on-lagging-category`); a pace set by per-step income moved only when that income was time-gated (`per-step-income-drives-speed-time-gate`), and the same gate had to be retired in a lineage without the disease (`time-gate-vs-wide-stance-retire-the-fix`).
Coach application. Ask every curriculum three questions: does it engage (show the internal state)? what does it count (process or lineage)? when is it present (against the pathology's phase)? Check where shipped checkpoints sit relative to every ramp.
doctrine-17Probe before training: feasibility first, hypotheses in tablesAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop, enumerate hypotheses in a written table audited against actual configs cheapest-first, race one probe per side of the sim2real boundary for hardware-only pathologies, and use suspended tests to acquit or convict actuators before blaming authority.
Case. "在黑暗里试钥匙" - four sidewalk rungs failed until an open-loop probe separated exploration/waveform/authority in one experiment (`open-loop-probe-before-reward-tuning`); the foot-drag mystery fell to a seven-hypothesis config audit (`hypothesis-table-code-audit`); the period-doubling was resolved by racing a reward-side and a plant-side evidence line - and both paid off, one per sub-case (`period-doubling-evidence-race`); the suspended test acquitted the roll actuator in one measurement (`suspended-test-isolates-actuator-authority`). A read-only configuration probe told a wall from a slope in the recovery line's seated basin (`configuration-probe-wall-not-slope`), and the fix it pointed to - where the feet are - took prone from 0/159 to 158/159 (`prone-dead-end-is-foot-placement`); a knob that did not move its variable was recorded as no test of the idea (`dof-vel-penalty-is-not-a-pacing-knob`).
Coach application. When a skill resists training, prescribe the probe before any further reward edits; require verified target trajectories before imitation terms; keep a falsified-fixes list so closed roads stay closed (`amplitude-cut-falsified-yaw-fix`).
doctrine-18External advice is recomputed locally; values transfer as ratiosEvery external suggestion is classified adopt / already-have / modify / trap by recomputing its claim on the local reward table and probe data; numeric values transfer only as dimensionless ratios (to tracking weight, leg length, sqrt(gL), control rate); citations are verified to exist.
Case. "Start vy very small" would have destroyed sidewalk learning on this reward table - the gradient scales quadratically (`external-advice-audit-against-own-arithmetic`); swing-height targets and weights transferred correctly only through leg-length and tracking-ratio scaling (`transfer-ratios-not-absolutes`); the "6-step delay" was refused for lacking a control rate (`latency-dr-covers-measured-pipeline`); a borrowed reference's structure was FK-verified and its amplitude re-derived from the division of labor (`reference-structure-fk-amplitude-division`); retrieval agents fabricated verbatim arXiv quotes - only source-verifiable material was used; and one dismissed suggestion later proved right for a different mechanism, and was credited (`cycle-average-tracking-for-gait-quantities`). An advisor's staged state machine turned out to exist in none of the three papers it cited, and reading them changed the plan (`advisor-paraphrase-vs-paper`).
Coach application. Intercept every "paper X does Y" with the local recomputation; convert absolutes to ratios before comparison; verify quotes; revisit dismissed advice when new mechanisms appear.
doctrine-19Hardware sessions are scripted experiments, not tuning sessionsReal-robot time executes a pre-registered matrix: risk-ordered (baseline first, fragile last with a spotter), stage-gated (suspended smoke before ground), A/B sessions bracketed by a repeated reference run, operators briefed on measured zero-command and untrained-axis behavior, chirality-aware disturbance protocols, no field tuning - the only legal field changes are scripted, single-variable, and self-reversing.
Case. The S2 acceptance sheet (`risk-ordered-real-deployment`, `battery-bracketed-real-ab`, `know-zero-command-behavior`, `push-test-chirality-protocol`, `no-field-tuning-protocol`); the RAM-only torque experiment with automatic power-cycle rollback (`reversible-single-variable-field-experiments`); and the sim-veto rule - even sim's condemnations get one safeguarded hardware check when they judge the purpose-built configuration (`sim-veto-needs-real-confirmation`). The recovery line's first real run went ahead with its preconditions unmet and was stopped as dangerous (`first-real-get-up-violent-stage-one-policy`); after it: a staged hang, mat and floor protocol (`staged-hang-mat-floor-for-get-up`), a fixed power-cycle pre-flight and two-machine discipline (`power-cycle-preflight`, `two-machine-config-discipline`), a fall guard replaced rather than switched off (`fall-guard-becomes-a-state`), and logs that are part of the run (`hardware-log-is-the-attribution-input`).
Coach application. Turn every hardware request into a runbook with order, gates, brackets, briefing, and anomaly plays; refuse improvised parameter changes on the floor.
doctrine-20Close questions in writing; restart when the debt is structuralAudited questions get frozen verdicts with citable wording and an explicit reopening bar; hardware verdicts are dated by deployment-stack and calibration state and expire when those change; and when successive rungs shuffle symptoms without net progress, freeze the lineage as regression baselines, pay the structural debts, and retrain minimal - carrying laws and instruments, not weights.
Case. The chirality and COM questions were closed with frozen wording and "no reopening without new hard evidence" (`frozen-verdicts-semantic-boundaries`); v5/v6's condemnations expired with the deploy stack (`stale-verdicts-under-old-stack`); a 2-degree calibration fix moved the whole runnable envelope (`zero-offset-calibration-shifts-envelope`); plant upgrades are era boundaries with paired re-baselining (`plant-swap-invariants-vs-shifts`); and the 2026-08-05 reset froze v5-v11, fixed the latency FIFO / manifest / sampling / reward-table debts, and restarted - producing the lineage that reached hardware SOTA (`freeze-lineage-fix-structure-restart`, `minimal-reward-table-with-provenance`). The recovery line's real-robot verdicts ended up in three places that disagree, one of them an undated note in a command file (`write-hardware-verdicts-back`).
Coach application. Maintain the closed-questions ledger and quote it when symptoms recur; stamp verdicts with stack/calibration versions; when a team is three rungs into symptom-shuffling, raise the restart question explicitly with the freeze-fix-restart pattern.
doctrine-21Name the quantity in the space it lives inA goal, reward term or acceptance criterion about the feet, the base or the contact state is computed from the quantity itself - world poses, forces, per-category outcomes - never through a joint-angle, single-signal or pooled stand-in that assumes everything else sits at nominal; and every detector is validated on a behaviour known not to contain the event before it becomes a gate.
Case. The recovery line was caught three times: |ankle roll| as "flat feet" sold stance width and the real robot slid into the splits, a hip-roll criterion was confounded by 50 deg of yaw, and the joint table said 0.271 m where the feet were 0.159 m apart; task-space terms produced the first flat, wide stance (`joint-space-proxy-for-task-space-quantity`). Flight detection lied in both directions across two lines - foot height flagged 40% false flight on a walking gait, contact force alone flagged slip chatter as hops (`contact-detector-single-signal-lies`). A pooled height average described a robot that did not exist - six in ten standing, four in ten sitting (`zero-partial-credit-is-not-an-iteration-problem`) - and the walking line had learned the same lesson on yaw rate (`heading-integral-not-body-rate`).
Coach application. For every reward term and gate row, ask what physical quantity it stands for and whether it is measured directly; flag joint-space or single-signal stand-ins for task-space goals, ask for a detector validated on a negative control, and split pooled metrics by category before reading them.
doctrine-22Continuation needs a live gradient; a release is chosen by a scanContinue a converged policy only on a change that creates a live gradient, on a short budget, with every checkpoint scanned on the transfer axis; choose a release by running the full battery over a band of checkpoints and stop on signals, never by taking the last one; and when edits to the terminal phase cannot move a behaviour, roll back and retrain with the constraint present from the start, keeping the order in which the lineage acquired its mechanisms as explicit curriculum phases.
Case. A continuation with no new gradient drifted MuJoCo transfer from 100/98% to 80/28% while every Isaac gate stayed perfect, and a live-gradient continuation at the same depth kept it (`converged-continuation-is-poison`). One-leg checkpoints 100 iterations apart failed 1 and 38 of 40 cells, and late ones degraded (`checkpoint-choice-is-a-full-gate-scan`). Four in-lineage stance fixes failed because the stance was the end of the get-up path, and from scratch it grew right (`stance-decided-by-get-up-path`); fixes stacked on degraded states were rolled back by the user (`stop-stacking-roll-back-and-audit`); and the lineage's final recipe, trained from scratch in one run, sat at 0% because the order of its curriculum was part of the product (`curriculum-history-is-part-of-the-product`). The omni line's short adaptation budgets and mature roots are the same law seen from the other side (`continuation-budget-not-from-zero`, `root-maturity-vs-product-quality`).
Coach application. Before approving a continuation, ask for the new gradient, the budget and the transfer axis in the scan; before approving a release, ask for the scan; after three rungs without progress on the target, propose rolling back to the last good checkpoint and a from-scratch phase plan instead of a fourth patch.
Experience cards
79 cards matching “hypothesis-table-code-audit”.
Compare the achieved reward to the computed ignore-floor to tell "never learned" from "learned but unprofitable"
ignore-floor-diagnosisFor any skill that trains flat, compute the reward the null policy would earn on that term; achieved==floor means the behavior never paid out (find why: exploration, reward observability, or feasibility) - do not tune weights first.
Symptom
C4 sidewalk failed on both arms; the question was whether the policy had found sidewalk and rejected it as unprofitable, or never found it at all - two diagnoses with opposite fixes.
Context
The theoretical value of the sidewalk tracking term for a policy that completely ignores the command was computable from the command distribution: 0.189. Trained final values landed at 0.187 (arm A) and 0.204 (arm B) - sitting exactly on the ignore-floor - while the honest balance at the optimum actually favored sidewalking (net +0.88/step inside the side bucket). Later the same arithmetic closed the whole saga: for the true reward landscape, doing real sidewalk scored 0.153 vs 0.944 for ignoring - the policy's refusal "是理性最优，不是探索失败" (rational optimum, not exploration failure) under one hypothesis, and under the final measurement-corrected account the policy had "每一次都在 做理性选择" (made the rational choice every time).
Change
Diagnostic rule adopted: compute the ignore-floor for the new term; if the achieved value sits on it, the behavior was never expressed in useful volume (or the reward cannot distinguish it - check both); if the achieved value is above floor but the behavior is absent at deployment, the policy sampled it and priced it out - then the reward balance, not exploration, is the lever.
Outcome
Correctly identified that PPO had not merely under-valued sidewalk; each subsequent hypothesis (waveform sign, regularization cage, exploration form, reward kernel) was tested against this floor arithmetic, which kept the search honest through three reversals.
Mechanism
Every reward term has a computable value under the null behavior; the achieved-vs-floor gap is a one-number audit of whether the optimizer ever monetized the target behavior. It converts "training failed" into one of two mechanistically distinct states with different fixes.
Applies when
- a new skill's tracking reward plateaus early
- deciding between exploration fixes and reward-weight fixes
- post-mortem of a failed curriculum rung
“track_lin_vel_y_exp 训练终值恰好坐在「完全无视指令」的底分上（A 0.187 / B 0.204，理论值 0.189），而终点 balance 明明有利（side 桶内净 +0.88/步）。不是学会了不划算，是根本没学到。”
train/C_LADDER_RUN.md § 3e. 为什么首战 FAIL The best checkpoint to SHIP is not the best checkpoint to CONTINUE FROM - maturity is capital against adaptation shock
root-maturity-vs-product-qualityDecide shipping points and fork roots separately: gates rank products, but a root candidate must prove itself by surviving a continuation under the next rung's shift (dual-arm if in doubt) - and prefer the more-trained point as root when product metrics conflict with maturity.
Symptom
A band re-audit found s1e-300 beat the incumbent root s1e-500 on nearly every quality gate (stepping 19/20 vs 13/20 with historically-best 26.9 mm swing, speed gate 14/20 vs 2/20, heading 26 vs 54 deg/20 s) - suggesting the root had been mis-picked and the younger point should take over.
Context
The dual-arm control settled it the other way: continuing the S2 PD rung from s1e-500 adapted smoothly (3/3 smoke throughout), while the b300 control arm (same config, from s1e-300) fell into a survival valley under the PD shock (+100 iters: 1/3 -> 0/3), never climbed out within budget, and its 800-iter product scored 13/20 survival - eliminated. Verdict: "幼年点自身指标再好也扛不住新 DR 适应冲击, 成熟度是本钱,s1e-500 根被数据背书" - a young point's own metrics, however good, do not survive new-DR adaptation shock; maturity is capital. The audit still yielded value: the band scan (200-1000, per-100) mapped the lineage's arc (200 dragging -> 300 peak -> 400+ decay -> 900+ drift blowout), and 300 remains the better PRODUCT answer for shipping-as-is questions.
Change
Selection doctrine split into two questions with different answers: best-product point (quality gates at the point itself) vs best-root point (survives adaptation shocks; more training age = more capital), each decided by its own evidence - and root claims settled by a dual-arm continuation test, not by point metrics.
Outcome
s1e-500 kept the root role with data behind it; the S2e ladder built on it passed rung after rung, while the b300 line was closed at the cost of one control arm.
Mechanism
Early checkpoints sit near sharp optima with less accumulated robustness structure; their headline metrics reflect the narrow training distribution, not resilience to distribution shifts. A continuation rung is itself a distribution shift, so the root property being selected for is shock tolerance - observable only by actually continuing, never by static gates.
Applies when
- a younger checkpoint outscores the current root on quality gates
- choosing the base for a robustification or command ladder
- a continuation run stalls in an early survival valley
“b300 对照臂 … PD 冲击下存活谷(+100 起 1/3→0/3),预算尽未爬出,800 档 20-seed 存活 13/20 出局——幼年点自身指标再好也扛不住新 DR 适应冲击,成熟度是本钱,s1e-500 根被数据背书”
train/README.md § omni_s2e_pd (b300 对照臂) / s1e 选点重审 Freeze the deployment contract, stamp every export, and let an automated checker catch wiring bugs
contract-freeze-and-checkerFreeze and fingerprint the policy I/O contract; ship contract changes as new versioned profiles that leave old artifacts bit-identical; and extend the automated contract checker with every pipeline change, forcing the new path to execute in the check.
Symptom
Contract-level changes (observation layout, action pipeline) are where silent sim/real divergence is born; two real wiring bugs appeared the one time the action pipeline was extended.
Context
The 215-dim observation contract was frozen ("纪元 3，三机 digest" - an era number plus a digest agreed across three machines); proposals that would break it (e.g. a GRU memory) were rejected on contract grounds. Every exported ONNX is stamped and verified with a manifest (onnx_manifest --stamp / --verify), and deployment refuses mismatched combinations. When C4 added the lateral feed-forward, it went in as a NEW profile (omni_ff) leaving the existing omni profile's behavior bit-identical; the checker (check_contract) was extended to force the feed-forward path to actually execute (cmd_vy=0.13) and promptly caught two genuine bugs: (1) re-clamping with soft_joint_pos_limits after the feed-forward (0.23 rad deviation) instead of reusing the parent's clip; (2) indexing processed actions by asset.joint_names instead of the action term's own contract-ordered _joint_names, which landed the feed-forward on the wrong joints (l_hip_yaw / r_ankle_pitch).
Change
Contract discipline as implemented: frozen dims + digest; manifest stamping and refusal; contract changes only via new versioned profiles; checker updated in the same commit as any pipeline change, with inputs chosen so new code paths are exercised.
Outcome
Both wiring bugs caught before any training or deployment ("两个都是 check_contract 当场抓出来的 —— 这次它值回票价"); old deployments provably unaffected by the new profile.
Mechanism
The contract is the only interface the policy and robot share; freezing plus fingerprinting makes divergence detectable, and an executable checker turns "the contract holds" from a belief into a test - but only if its inputs actually drive the new code path.
Applies when
- modifying the action or observation pipeline of a deployed policy
- exporting policies for hardware
- proposals that would change observation dims or history structure
“契约校验抓到的两个真错误（记账，别再犯）：1. 前馈后误用 soft_joint_pos_limits（URDF 限位 ×0.9）重钳 → 0.23 rad 偏差 … 2. 用 asset.joint_names 索引 _processed_actions → 前馈落到 l_hip_yaw/r_ankle_pitch 上 … 两个都是 check_contract 当场抓出来的 —— 这次它值回票价。”
train/C_LADDER_RUN.md § 3j. 契约级改动 / 契约校验抓到的两个真错误 Add a termination that makes the degenerate strategy fatal - no height cut-off meant crouch-shuffling could live forever
termination-closes-degenerate-basinFor each known degenerate strategy, check whether the termination set makes it fatal; if the robot can live indefinitely inside the degenerate posture, add a termination just past the intended operating envelope rather than escalating penalties.
Symptom
Crouched foot-dragging survived indefinitely because the termination set contained only bad_orientation (40 deg) and base contact - there was no height termination at all, so a deep squat was a viable long-term strategy.
Context
The hypothesis audit found the missing termination (hypothesis 7); the cross-check against published configs found the field practice: Booster terminates at 0.45 m (38% of body height) and the research warning is that the termination height must not be so low that crouching survives it. The proposed value: 0.32 m, just below the walk crouch base height 0.3739 - a deep squat terminates immediately, "断掉蹲着蹭的活路" (cutting off the crouch-shuffle's livelihood).
Change
Add height termination at 0.32 m as a second-priority item of the walk fix package, alongside restoring base_height_l2 to -10.
Outcome
Entered the v5/v6 fix package under which the crouch-shuffle optimum disappeared (34 mm clearance, 87% tracking by v6).
Mechanism
Termination conditions define which strategies exist at all: a reward penalty prices a behavior, but a termination deletes its future returns entirely. Degenerate basins that are merely penalized can remain optimal under enough tracking pressure; a termination placed between the degenerate posture and the intended one makes the basin unreachable as a steady state.
Applies when
- a degenerate but stable behavior persists across reward tunings
- auditing termination conditions for a locomotion task
- a policy exploits the gap between penalized and terminated states
“加终止高度:研究第 6 条"终止高度不能低到让蹲着也能活"。我们完全没有高度终止。建议 0.32 m(略低于 walk 蹲姿基座高 0.3739,深蹲即终止)。… 加终止高度 0.32 m(深蹲即终止,断掉蹲着蹭的活路)”
train/WALK_DIAGNOSIS.md § 修正 ④ / 最终改动清单 第二优先 Set torque limits per joint from measured gait peaks - a uniform percentage is the wrong shape, and training must use the deployed numbers
torque-limit-shape-by-measured-peaksMeasure per-joint torque peaks in the actual gait and set each limit as measured-peak x margin capped at rating; then propagate the same numbers into training and add an automated deploy-time consistency check - never derate by a uniform percentage, never let training assume torque deployment will not grant.
Symptom
A uniform 50% torque derating (18/8.5/7) had piled safety margin on the joints that never use it while cutting the busiest joint below half its measured demand.
Context
Per-joint gait peaks were measured (walk_v5 at cmd 0.3/0.6): RS06 (hip_pitch/knee) uses 5.5-5.9 N*m = 15-16% of its 36 N*m rating - cutting it to 12 is a free safety win; RS02's ankle_pitch runs at 16.2 N*m = 95% of its 17 N*m rating - "它是速度的硬件瓶颈", no room to cut; RS00 measured 36-44%, capped at 11. The resulting shape 12/17/11 replaced the uniform percentage. Sweeps across several limit sets (rated / 50% / 14-17-11 / 12-17-11) produced identical speed, lift, and landing force - within this range the limits do not shape the gait; what matters is consistency: "关键是训练和硬件必须是同一个数", because the exporter fills effort_limit from tau_limit, and a policy trained at rated 36/17/14 "会假设有三倍力矩可用" while deployed at 12/17/11 (exactly the v5 cross-generation inconsistency later suspected in its wild kicking).
Change
robot.yaml tau_limit set to the measured-shape 12/17/11, firmware written to match, and train/isaac_values.py regenerated so training sees the same limits; the deploy tool self-checks limits against robot.yaml on every run.
Outcome
Free safety margin captured where demand is low, the real bottleneck joint left at rating, and the train/deploy torque worlds unified with an automated consistency check.
Mechanism
Torque demand is grossly unequal across joints in a gait (15% vs 95% of rating here); a uniform percentage misallocates the safety budget by construction. And since the trainer treats effort_limit as a plant truth, any train/deploy mismatch is an invisible plant gap of exactly the mismatch ratio.
Applies when
- choosing safety torque limits for a legged platform
- training-vs-deployment actuator limit audit
- one joint runs near rating while others idle
“曾用统一 50%(18/8.5/7)是错的形状: 把余量堆在用不到的 RS06 上, 却把 ankle_pitch 砍到需求的 52%。… RS02 在 0.6 m/s 已用到额定 95%, 它是速度的硬件瓶颈 … 实测多组限幅 … 完全一致 —— 限幅在这个范围对步态零影响, 关键是训练和硬件必须是同一个数。… 若训练仍按额定 36/17/14, 学出的策略会假设有三倍力矩可用。”
train/WALK_V6_MINIMAL.md § 3. 训练侧必须同步的一件事 When the training reset distribution changes, freeze the acceptance distribution separately and pin its seed - the same checkpoint measured twice differed by 3.8 and 10.2 points
frozen-acceptance-distribution-and-pinned-seedAcceptance distributions are frozen artifacts, decoupled from whatever the training distribution becomes and evaluated with a pinned seed, and every gate row carries its sample size so that a small-n row is never read as a regression.
Symptom
R0.3 added easier roll-arc start states to the training resets, and the acceptance script shared the training category table; separately, the same checkpoint scored side 3.8 points and mid 10.2 points differently on two runs of the same script.
Context
Acceptance ran 512 parallel envs drawn from the fall categories. Had it kept following the training table, 15% of acceptance samples would have landed on states easier than prone - inflated scores and generations that could not be compared. The two same-checkpoint runs had identical per-item height medians, so the ruler had not changed; the spread was reset resampling noise (side n ~ 169, sigma 2.3%; mid n ~ 35, sigma 8.3%). The spec's "20 seeds" had always meant controlled seeds.
Change
accept_recovery.ACCEPT_CATEGORIES pinned to the four R0-R0.2 categories and decoupled from the training FALL_CATEGORIES; --seed 20260809 pinned, after which two consecutive runs were bit-identical. The mid row (n ~ 35) was labelled the bluntest gate.
Outcome
Every later generation (R0.3 through V3.1) was scored on the frozen distribution and seed, which is what let R0.3's intermediate state be read as "no measurable gain" (62.7 -> 62.1%) and R0.2's mid drop be booked as noise rather than a regression.
Mechanism
An acceptance set that follows the training distribution measures a moving target, and an unpinned reset draw adds sampling noise that small-n rows cannot absorb.
Applies when
- the training reset or command distribution changes between generations
- repeated evaluations of one checkpoint disagree
- a small category drives a pass/fail decision
“**分布冻结**:`accept_recovery.ACCEPT_CATEGORIES` 钉死 §5 四类 … 与训练侧 `FALL_CATEGORIES` **解耦**。 … **side 差 3.8 点、mid 差 10.2 点**(h 中位逐项一致,证明不是尺子变了)—— 纯 reset 重采样噪声 … 钉死后两次连跑逐位相同。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §14 验收尺子的两处加固(R0.3 起生效,向后兼容) Every rung gets written stop criteria - hit any one, stop; tightened when priors say results should come fast
preregistered-stop-criteria-per-rungFreeze per-rung stop criteria (old-skill floors, new-skill deadline, oscillation signature, known pathology signatures) before training, stop on first hit - and shorten the deadline in proportion to how fast your mechanism says results should appear.
Symptom
Continued training past the point of degradation had previously destroyed capabilities (C1 trained away the root's backward skill); without hard stop rules, sunk-cost reasoning keeps runs alive too long.
Context
Standard rung protocol - eval_c_matrix every 100 iters at 5 seeds with a fixed criteria list, frozen before training ("开训前写死，事后不许改"): (1) stand or vx+0.15 at <=3/5 for two consecutive points; (2) vx+0.15 tracking <70% for two consecutive points (vs recorded root baseline); (3) oscillation signature - survival repeatedly crossing zero between adjacent checkpoints, stop on first occurrence, do not wait for confirmation; (4) new-skill-no-progress deadline (e.g. wz tracking <30% or still same-signed after iter 400); (5) a known lineage pathology signature (s1c arm-B: scatter -> half-recover -> collapse).
Change
Stop budgets scale with prior knowledge: when C4-redo4's feed-forward was already proven open-loop, the no-progress deadline was tightened from +500 to +100 iters ("前馈是开环就给 71~96% 的 … 若 +100 还没有 … 不值得再烧").
Outcome
Multiple rungs were stopped exactly on criterion (C4-redo criterion 4 at iter 1200; redo2/redo3 at absolute 900), converting each into a clean hypothesis test instead of a drifting run; no rung burned its full cap on a dead hypothesis.
Mechanism
Degradation of retained skills is a lineage-level injury that later training often cannot undo, so detection latency is capital loss; and a stop rule written before the run cannot be bent by hope. Tightening deadlines when priors predict immediate results converts "no result yet" into evidence against the mechanism.
Applies when
- starting any resumed/curriculum training rung
- deciding whether to keep training a run that shows early regression
- a mechanism-backed change should produce results immediately
“每 100 iter eval_c_matrix.py --seeds 5，命中任一即停 … 存活在相邻 checkpoint 间反复跨越 0（出现即停）… 收紧版：绝对 iter 900（= +200）时 vy±0.10 跟踪仍 <30% 即停”
train/C_LADDER_RUN.md § 3h. 预注册停梯判据（开训前写死，事后不许改） Gate a new reward term by its command so all old modes score pointwise identical
gate-new-reward-terms-by-commandWhen a reward term must be added mid-lineage, gate it on the condition that defines the new task so every pre-existing situation scores exactly as before - and still watch for value-rescale pathologies inside the new mode.
Symptom
Adding a lateral tracking reward (track_lin_vel_y_exp) ungated would have paid 0-2.0 per step even in modes with cmd_vy = 0 (healthy gait sway of vy ~0.1 already earns 1.28), shifting the whole reward table by a large bias and rescaling the value function - no longer "just adding one mode".
Context
C4 was the C ladder's only true reward surgery. Single-variable discipline required that the change be invisible to every existing mode. The chosen construction: gate_by_cmd=True - the term pays only when |cmd_vy| > 0.02, so for all modes with cmd_vy == 0 the term is pointwise zero, i.e. the reward is pointwise identical to before the change. The same trick appeared earlier in C1: replacing the vy L2 tax with a command-error version that is "对 cmd_vy≡0 逐点同值" (pointwise equal when cmd_vy is 0), explicitly classified as not-a-reward-change.
Change
track_lin_vel_y_exp added with gate_by_cmd=True (weight +2.0, std 0.15); the residual acknowledged honestly - inside the side bucket the values DO change, so the rung still watched the known reward-reshuffle pathology signature (s1c B-arm: scatter -> half-recover -> collapse) as a stop criterion.
Outcome
Old modes provably unaffected (pointwise-equal argument); attribution for any change in old-skill metrics stayed clean through the C4 redo series.
Mechanism
PPO's critic normalizes to the reward scale it sees; an ungated additive term shifts returns in every state and re-scales advantages globally, entangling the new skill with all old ones. Command-gating confines the new term's support to the new mode's state distribution, making "pointwise identical elsewhere" a provable property rather than a hope.
Applies when
- adding a tracking/shaping term for a new command or skill to a lineage that must not regress
- reward change proposed while other skills are still being gated
- reviewing whether a config diff counts as a reward change
“只在 |cmd_vy| > 0.02 时付。不门控的话它对 cmd_vy≡0 的老模式也给 0~2.0 分（健康摇摆 vy≈0.1 → 1.28），等于给整张奖励表加一个大偏置、值函数尺度全变 … 门控后老模式逐点得 0 = 与加项前逐点同值，单变量纪律成立。… 但 side 桶内的值确实变了 —— 这仍是奖励表改版，开级盯 s1c B 臂签名”
train/C_LADDER_RUN.md § 3d. gate_by_cmd=True（重要） The hip_roll (l+r) asymmetry scalar predicted real-robot lateral drift - promote validated sim scalars into the gate
hip-roll-sum-predicts-lateral-driftHunt for cheap sim scalars that predict real-robot behaviors, validate them on direction AND ordering across multiple policies, then promote them into the acceptance battery; treat later violations as debt to justify in writing, not noise to ignore.
Symptom
A persistent hip_roll left/right asymmetry row in the sim2sim symmetry table had been dismissed as "calibration or mechanical asymmetry" noise; meanwhile real deployments drifted sideways by policy-dependent amounts.
Context
Forward-kinematics analysis reframed the scalar: both hip_rolls move the feet in +y for positive angle, so a same-signed (l+r) sum IS a lateral translation mode - the scalar is a direct lateral-drift bias estimate. Checked against real deployments: s1e (l+r = -0.0178, smallest magnitude) was the steadiest with least drift; 700 (+0.0253) drifted mildly left; A800 (+0.0267) drifted clearly left with the largest tilt 12.9 deg. Direction correct 3/3, ordering correct 3/3 (the log's heading calls it "四枚四中", four-for-four).
Change
The scalar was promoted into the acceptance battery as a posture-class criterion alongside tilt-max median: "hip_roll 左右不对称 |l+r| 不得比父代大" - doubling as a heat proxy (error ~ torque ~ heating).
Outcome
Used at every later gate; when the C4 product exceeded it by +0.005 rad (~+0.3 deg vs parent), the criterion was not silently waived - it was booked as explicit debt with a mechanism argument (the increment is task-required, far smaller than the sidewalk amplitude +/-2.2 deg) plus a related account (stand saturation 32.4% -> 37.2%).
Mechanism
A policy's static joint-angle bias in a translation-producing mode integrates into real-world drift; sim can measure that bias precisely and cheaply. A sim scalar earns gate status exactly when its predictions are validated against hardware in both direction and ordering - and a validated gate may only be exceeded with a written mechanism-level justification, never silently.
Conflicts
The log's heading says "四枚四中" (4/4) but the evidence table lists three policies and the text says "方向 3/3、排序 3/3"; the fourth instance is not shown in this file.
Applies when
- a real robot drifts or leans in a policy-dependent way
- deciding which sim measurements deserve gate status
- a validated gate criterion is marginally exceeded by a new product
“s1e | −0.0178（绝对值最小）| 微右、最不飘 | 三者中最稳、飘最小 ✓ … A800 | +0.0267 | 左、最飘 | 明显左飘、倾角最大 12.9° ✓ 方向 3/3、排序 3/3。 → 正式纳入验收表（与「倾角 max 中位」并列为姿态类判据）。”
train/C_LADDER_RUN.md § 3e. 顺带：hip_roll 左右不对称 (l+r) 就是横移偏置 —— 四枚四中 The trainer read a stale USD after the URDF mass update - regenerate derived assets and gate on an automated equality instrument
derived-asset-staleness-checkFor every derived plant artifact (USD from URDF, generated value files), pair the generation step with an automated source-vs-derived equality instrument, prove the instrument can fail, gate training on its PASS, and re-run physical audits after every regeneration.
Symptom
Measured link masses had been committed to URDF/MJCF (total 9.58 -> 9.792 kg, weighed values), but Isaac reads the derived USD asset - which still carried the old masses: a silent 2.2% mass fork between the training plant and the evaluation plant.
Context
The v12 checklist made USD regeneration a hard precondition ("硬性 前置") and, crucially, backed it with an instrument: check_usd_mass.py compares USD vs URDF per-link mass AND inertia trace, validated by showing it FAILs the stale asset naming 9 offending links, then PASSes after re-conversion (13/13 links consistent, total 9.7920). The self-collision filter audit was re-run after the regeneration (three poses, 0.00 N) because a regenerated asset invalidates physical audits done on the old one. This milestone was also where the three plants first aligned: "三边 plant 首次对齐(armature+摩擦+ 实称质量)就在这一代".
Change
convert_urdf re-run on the training machine, regenerated asset committed, check_usd_mass.py PASS required as an acceptance gate for the generation; dependent audits repeated post-regeneration.
Outcome
The 2.2% plant fork was closed before it could distort a generation's acceptance numbers; the staleness class of bug now has a permanent detector instead of a memory.
Mechanism
Source-of-truth edits do not propagate to derived binary assets by themselves; any consumer reading the derivative silently trains or evaluates on the old plant. An automated equality check between source and derivative - proven able to fail - turns an invisible staleness into a red gate, and regeneration invalidates every audit performed on the old artifact.
Applies when
- editing masses/inertia/geometry in URDF or MJCF sources
- a trainer or evaluator consumes converted/derived assets
- plant numbers differ between simulators for no visible reason
“25ba997 把连杆质量更新为实称值(总重 9.58→9.792 kg,URDF/MJCF 已改),但 Isaac 读的是 train/assets/laika_v2.usd —— 仍是旧质量。… 否则 Isaac(9.58)与 MuJoCo(9.79)质量分叉 2.2%,v12 验收数字失真。验收门:python tools/check_usd_mass.py 必须 PASS … 对旧资产实测 FAIL/9 连杆点名,仪器已验证”
train/WALK_V12_SPEC.md § 7. 核查单 (⚠️ 先重转 USD) Slowing the gait clock at deployment is out-of-distribution and backfires - lower the commanded speed instead, or train the knob
cycle-time-override-is-oodAny deployment override must correspond to a dimension the policy was trained to handle; to make a parameter field-adjustable, randomize it in training and observe it - otherwise use the levers inside the trained envelope (commands) and leave the knob alone.
Symptom
Real-robot feedback "walks very fast and unstable" suggested slowing the gait; a deploy-side --cycle-time override existed, making "just slow the clock" a one-flag temptation.
Context
A sim sweep of the override on walk_v6 @cmd 0.3 showed monotone degradation away from the trained 0.40 s cycle: at 0.50 s tilt jumped 7.9 -> 13.2 deg and landing force 1.52x -> 2.24x; at 0.80 s (half speed) clearance collapsed to 3 mm - dragging again - with 20 deg tilt. Meanwhile the legitimate lever, lowering the commanded speed with the clock untouched, improved everything monotonically: cmd 0.1 gave 104% tracking, 6.7 deg tilt, minimum slip - the most stable operating point. The file distinguishes the two "slows" explicitly: lower command = smaller steps at the same 2.5 Hz rhythm; a slower rhythm itself requires retraining - randomize cycle_time (e.g. 0.40-0.65 s) during training and expose it as an observation, and only then does --cycle-time become a field-adjustable knob.
Change
Deployment guidance: never ship a cycle-time override the policy was not trained under; respond to "too fast/unstable" with lower commands; schedule clock variability as a training-time (contract-level) change if a field knob is wanted.
Outcome
The sweep quantified the trap before hardware paid for it (dragging and 2.2x landing force at slowed clocks); cmd 0.1 documented as the stable demo point.
Mechanism
The policy is a function fitted around the training distribution; a deploy-side override moves an input (phase rate) to values never seen, so behavior degrades unpredictably - the knob LOOKS like a capability because it exists in the code, but capability lives in the training distribution, not the interface.
Applies when
- a deploy tool exposes overrides (clock, scale, gains) beyond the training distribution
- hardware feels "too fast/aggressive" and a quick knob exists
- deciding between a deploy-side tweak and a retrain
“0.80s | 1.25Hz | 0.165 | 3mm(拖地) | 20.0° … 慢一半直接崩 … 策略按 0.40 训练, 别的周期属分布外。… 降指令速度才是有效杠杆 … cmd 0.1 是最稳的工作点。… 要节奏本身变慢必须重训 —— 训练期把 cycle_time 随机化(如 0.40~0.65s)并作为观测的一维, 部署时 --cycle-time 就成了现场可调的旋钮。”
train/WALK_DIAGNOSIS.md § 2026-08-01 追加: 调慢步态时钟(--cycle-time)在仿真里是反效果 A suspended (no-load) test acquits or convicts the actuator before you blame authority
suspended-test-isolates-actuator-authorityBefore attributing a failure to actuator authority, measure no-load tracking error and steady-state torque fraction; blame authority only if the task fails while the error grows with demanded force - and then fix gains or targets, not training.
Symptom
hip_roll sagged 0.21 rad on the ground and saturation questions loomed over the sidewalk plan - was the roll axis physically too weak (authority), or was something else limiting it?
Context
Before C4, the roll-authority question was settled by measurement triage: suspended test (--suspend, feet off ground) showed hip_roll tracking error 0.0008 rad - actuator acquitted; the entire 0.21 rad ground sag is load-induced. Steady-state torque was 25% of limit - 75% margin remains. Since sidewalk needs lateral force, not exact angles, authority was ruled "not a hard limit", with a pre-registered criterion for when it WOULD become one: sidewalk fails to track AND roll error keeps growing - then the fix is raising hip_roll kp or lowering the vy target, not more training.
Change
Hypothesis "roll authority insufficient" demoted from blocker to a monitored branch with an explicit trigger condition; C4 proceeded.
Outcome
Later open-loop probes confirmed the actuator could produce the behavior (sidewalk feed-forward ran at full amplitude, 5/5 survival), and the eventual C4 failure causes were measurement and reward, never authority.
Mechanism
Suspended vs loaded comparison separates the actuator's closed-loop competence from the load path: tiny no-load tracking error means the motor/controller is fine and any loaded deviation is statics (gravity / stiffness budget, kp trading error for force). Torque-fraction measurement then bounds how much force headroom actually remains.
Applies when
- suspecting an axis is "too weak" for a new skill
- large position sag on a loaded joint
- deciding between hardware fix, gain change, and more training
“吊挂（--suspend）实测 hip_roll 跟踪误差 0.0008 rad → 执行器无罪，地面下垂 0.21 rad 全是负载所致；稳态占限扭 25% → 仍有 75% 扭矩余量。… 判据：若 C4 出现「侧走跟不动且 roll 误差继续变大」，那才是权限账 … 解法是提 hip_roll 的 kp 或降 vy 目标，不是硬训。”
train/C_LADDER_RUN.md § 3d. roll 权限：已部分澄清，不是硬上限 A real-robot verdict is (policy x deployment stack) - when the stack changes materially, old verdicts expire
stale-verdicts-under-old-stackDate every hardware verdict with the deployment-stack version it was measured under; after any material stack change, re-test before trusting old condemnations or old praises - with the interpretation of each possible result written down first.
Symptom
walk_v5 stood condemned as "kicks wildly" and walk_v6 as "cannot walk unassisted" - but those verdicts were issued under an earlier deployment stack (--heading did not exist yet, several fixes had just landed); only v7 had ever run under the current unified stack.
Context
New sim evidence sharpened the doubt: a same-harness four-version sweep showed v6 was the HEALTHIEST archive at the real operating point (cmd 0.15: dominant frequency locked at 2.50, steps 35:35 perfectly symmetric, foot distance 203/190 mm best of four, mean tilt 4.2 deg, saturation 15%). A full re-test under the unified stack was scheduled with per-version questions and a pre-filled interpretation table ("判读表(预填假设,回来对号)"): e.g. v6 walks + frequency ~2.5 -> old verdict was the stack's fault, v6 becomes the comparison champion; v6 walks but at ~1.25 -> period-doubling on hardware = confirmed plant gap, actuator fitting promoted to mainline; v5 no longer kicks -> the kicking was an old-stack artifact.
Change
All four versions re-queued on hardware under one stack (same torque limits, slew profile, heading loop, logging), with the version-specific legacy profile pinned; verdicts held provisional until re-issued.
Outcome
The re-test design separated policy properties from stack artifacts before any policy was permanently written off - and turned each outcome into a specific conclusion via the pre-filled table.
Mechanism
A deployed behavior is produced by the policy plus everything between it and the motors (heading loop, slew limits, torque caps, clock); verdicts implicitly condition on that whole stack. Fixing the stack invalidates the conditioning, so old failures may be stack artifacts and old successes may not survive either.
Applies when
- deployment tooling (limits, filters, loops) changed since a policy was last judged
- deciding which historical policy is the rightful baseline
- a sim sweep contradicts an old hardware verdict
“只有 v7 在完整的今日部署栈下上过真机 … v5"左右乱踢"、v6"未能自主"的判决全部来自更早的栈(--heading 尚不存在, 部分修复刚落地)——判决已过期。且 2026-08-02 四代同机仿真横测翻出了新证据:v6 在真机工况(cmd 0.15)下是四代里最健康的仿真档案”
train/REAL_SWEEP_V5_V8.md § 0. 为什么重测 When training fails repeatedly, inject the target behavior open-loop - stop tuning rewards for an unverified behavior
open-loop-probe-before-reward-tuningAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop on the real plant/sim first, and only resume training once you hold a measured, safe, sign-verified target trajectory.
Symptom
Three sidewalk training rounds failed; hypotheses multiplied (exploration failure / wrong reference waveform / insufficient authority) with no way to pick between them by running more training.
Context
Instead of a fourth reward guess, the team wrote probe_side_ref.py: the candidate reference is injected open-loop on top of a frozen policy's output (bypassing PPO entirely), directly measuring "what happens if the robot literally does this waveform" - separating all three hypotheses in one experiment (5 seeds x 8 s per condition, several waveform families and gains). The probe immediately eliminated the authority hypothesis (full-amplitude execution, 5/5 survival) and localized the problem to the waveform/measurement side. The closing principle was written down after the saga: without a verified target behavior, tuning rewards is "在黑暗里试钥匙" (trying keys in the dark).
Change
Standing method: before opening another training rung on a failing skill, build an open-loop (or task-space) generator of the intended behavior, measure whether the physical system can express it and what it looks like - then train toward a verified, quantified target.
Outcome
The probe chain produced the verified waveform (reversed-sign triangle, half gain), quantified safe amplitude (tilt 8.2 deg at band top, foot distance clear of the wall), exposed the metric bug when probe and training disagreed, and ultimately supplied the feed-forward that made C4 pass in +100 iters.
Mechanism
Training couples exploration, reward design, and feasibility into one opaque outcome; open-loop injection cuts the loop and tests feasibility and waveform alone. A behavior demonstrated open-loop converts the remaining failure into a pure credit-assignment/reward question - and its measured trajectory becomes the reference itself.
Applies when
- repeated training failures on one skill with multiple live hypotheses
- uncertainty whether the platform can physically express the behavior
- a reference trajectory's shape/sign/amplitude is guessed, not measured
“三轮 FAIL 之后不再猜，写 train/probe_side_ref.py 把参考开环注入到策略输出之上（绕过 PPO），直接量「照这个波形做会怎样」，一次分开三个假说：甲 探索 / 乙 波形 / 丙 权限。”
train/C_LADDER_RUN.md § 3f. C4 真因定谳（开环探针） / 3k. 建议的下一步 Real robot walked at half the sim clock for two generations - resolved by racing a reward-side and a plant-side evidence line, not by guessing
period-doubling-evidence-raceFor a hardware-only pathology, refuse to guess: pre-register one probe per side of the sim2real boundary (can the reward mechanism change it on hardware? can fitted plant parameters reproduce it in sim?) and let the first positive result direct the next version.
Symptom
The number-one sim2real gap: on hardware v6/v7 stepped at 1.23-1.32 Hz - almost exactly half the 2.50 Hz gait clock they were trained and simulated at; sim never reproduced it, two generations running.
Context
Instead of committing training budget to a guess, v8 pre-registered two mutually controlled evidence lines and kept the clock OUT of the training variables: (a) reward-side - if the v8 saturation fix revives joint_pos_ref (the term that pins the gait to the clock), re-run hardware and see whether frequency returns to 2.5 Hz (hypothesis: v7's frozen actions meant NO reward was pinning the gait to the clock, and the real plant - with armature and friction making high frequencies expensive - slid down to the leg's pendulum natural frequency ~1.1 Hz); (b) plant-side - record suspended joint data (fit_actuator), fit armature/friction, load the fitted values into sim2sim and see whether the 1.25 Hz reproduces IN SIM. Decision rule fixed in advance: "谁先给出阳性结果谁定 v9 的方向 (奖励侧 vs plant 侧)" - whichever line goes positive first sets the next version's direction.
Change
Period-doubling excluded from the v8 change set; both diagnostic lines scheduled in parallel as non-blocking work; frequency reported factually in acceptance with no pass/fail attached ("倍周期是否消失 不设判定,它是 §9 的关键证据").
Outcome
The gap was routed into a decisive-experiment structure rather than a speculative retrain; the plant-side line pointed at exactly the unmodeled armature/friction that were later measured and installed as the plant baseline. Resolution (era-2c full-plant retest): the family had TWO causes - v8's low-speed period-doubling vanished once measured armature+friction were installed (1.30 -> 2.50 Hz, bifurcation-edge machine sensitivity), while v7's stood untouched at 1.20 Hz (saturation-freeze-driven policy property) - both evidence lines paid off, one per case.
Mechanism
A behavior appearing only on hardware has candidate causes on both sides of the sim2real boundary; changing training to fix it tests only one side per expensive cycle. Two cheap parallel probes - one intervening on the reward mechanism, one making sim reproduce the real behavior - localize the cause to a side before any training money is spent, and sim-reproduction of a real pathology is itself the strongest form of plant validation.
Applies when
- a gait pathology appears on hardware but never in any simulator
- deciding whether a sim2real gap is reward-side or plant-side
- tempted to change the gait clock/reward to chase a hardware symptom
“倍周期(真机 1.23~1.32 Hz ≈ 时钟一半,v6/v7 连续两代;sim 从不出现):两条证据线互为对照——(a)… 真机重跑看频率是否回 2.5 Hz(假说:v7 没有任何奖励把步态钉在时钟上,真机 plant 有 armature/摩擦、高频贵,自由滑落到复摆自然频率 ~1.1 Hz);(b)真机吊挂录 fit_actuator.py … 看能否在仿真里复现 1.25 Hz。谁先给出阳性结果谁定 v9 的方向。”
train/WALK_V8_SPEC.md § 9. 平行线 (倍周期) A reward on a quantity the actor cannot observe teaches "produce less of it", never "correct it" - closed-loop correction needs an outer loop
reward-observability-limitBefore adding a reward, check the actor can observe (or infer) the quantity: unobservable-error rewards buy only average suppression - route correction tasks to an outer loop whose commands stay in distribution, and do not break a frozen contract to add an observation a deploy-side loop can supply.
Symptom
Heading kept drifting despite world-frame yaw rewards, and a reviewer proposed heading-error rewards - raising the question of what yaw shaping can even teach this actor.
Context
The adopted architectural verdict: the actor's 45-dim base observation cannot see accumulated heading at all - projected_gravity is invariant to rotation about the gravity axis, and omega_z is a rate, not an angle. World-frame yaw-rate rewards are therefore privileged shaping that can only teach "少产生旋转" (generate less rotation), never "偏了以后拉回原线" (pull back to the line after drifting) - the policy cannot represent the error it would need to correct. The S1 gate (<=5 deg / 10 s) demands exactly the former, so the stack is right for its gate; active heading correction is assigned to the deployment outer loop (--heading P-loop converting heading error into in-distribution wz commands) plus small-wz training - and the 215-dim contract is explicitly NOT extended with a heading observation ("契约不加 heading 观测,冻结不动"). The reviewer's companion bias hypothesis was adjudicated with data: drift is bimodal - a basin mechanism decides whether you leave (seeds vary +/-16-46 deg vs -385 to -391 deg), and once out, rotation direction is constant (weight chirality; candidate root: the phase clock always swings left first).
Change
Yaw shaping kept as rate-tracking (three-layer stack); heading correction owned by the deploy outer loop; contract frozen; the "which behaviors need an outer loop" question settled by observability analysis rather than reward tuning.
Outcome
Stopped a contract change and a futile reward direction; drift work split correctly into rate-suppression (trainable) and error correction (outer loop), consistent with the earlier measured 10x drift reduction from the deploy-side loop.
Mechanism
A policy can only condition on its observation sigma-algebra; rewards on functions outside it shift the marginal action distribution (open-loop average effects) but cannot create feedback on the unobserved variable. Whether to add an observation, an outer loop, or accept average-shaping is decided by the task's gate: suppression gates need shaping, correction gates need the variable in some loop's view.
Applies when
- adding rewards on accumulated/世界-frame quantities (heading, position)
- deciding between a new observation, an outer loop, and shaping
- a drift symptom persists across reward-weight changes
“actor 的 45 维基座观测不到累计航向(projected_gravity 对绕重力轴旋转不变,ωz 是速率不是角度)——世界系 yaw 奖励是特权塑形,只能教「少产生旋转」,不能教「偏了以后拉回原线」。… 主动纠偏闭环 = S3 把小 wz 进分布 + deploy --heading 外环 … 215 契约不加 heading 观测,冻结不动。”
train/OMNI_V0_SPEC.md § 3. 评审④判决(2026-08-06,S1.3 开训前) Low-friction robustness traced to kd DR bandwidth, not friction training - by digging resolved params across 8 lineages, 3840 cells
kd-bandwidth-mu-law-attributionAttribute capability differences by tabulating every lineage's resolved training params and eliminating zero-variance and non-aligned columns first; never let an eval-side override knob serve as the explanation axis, and never write a mechanism into a law before it survives a targeted test.
Symptom
Lineages differed wildly in low-ground-friction survival, and the intuitive explanation - "some trained ground friction, some didn't" - was about to steer the ladder toward a ground-mu training rung.
Context
The attribution ran as a full parameter-vs-result cross: 8 lineages x 4 eval kd levels x 6 mu levels x 20 seeds = 3840 cells, with each lineage's RESOLVED training params dug out and compared item by item. First kill: all 8 lineages had ground mu pinned at (1.0,1.0) - zero variance - so low-mu differences cannot come from friction training at all. The only training parameter aligned with the mu score was kd DR bandwidth: narrow (<=0.24) lineages scored 19.9/19.5/19.5, wide (>=0.40) scored 17.1/15.2/14.6/14.2/12.8 - the two groups completely non-overlapping. Every rival was excluded item by item (kd center no; kp band no; COM small-beneficial non-driving; friction rung a clean double null 19.5->19.5 and 15.2->14.6; iteration count non-monotonic), and the one clean single-variable causal link confirmed it: the s2e-3 kd surgery (0.7,1.3)->(1.08,1.32) moved the score 17.1->19.5. Counter-proof against "each best at its own operating point": the narrow-band lineage evaluated OUT of band (18.2) still beat the wide-band lineage at its own band center (9.2). Two axes were ordered never to be conflated (the first attribution's own error): training kd bandwidth is a parameter axis / lineage property; the eval-side --kd-scale knob is a plant axis (more damping physically helps on slippery floors for ALL policies) - "plant 轴只能当部署缓解,不能当 归因". A tempting mechanism story ("drag vs step attractor") was tested and falsified, and explicitly kept OUT of the law: "机制未定, 不入定律".
Change
The planned ground-mu training rung was recommended closed ("建议 不开") in favor of a kd band-narrowing rung (0.8,1.2)->(0.9,1.1) centered on the deployed value - with a pre-registered risk that the law demands "bandwidth = measured dispersion" and the real robot's kd dispersion was not yet measured; if it exceeds +/-10%, narrowing sacrifices real coverage and the rung must yield.
Outcome
A whole training rung was deleted from the ladder by attribution alone (the second S2 pass dropped mu and push, 5 rungs -> 3); floor material became a deployment-selection input (mu <~0.6 -> deploy the kd1.2 gain profile) rather than a training target.
Mechanism
Cross-lineage performance differences must be attributed over the actual training-parameter table, not over eval knobs or plausible stories: eval knobs act on the plant for every policy (a physical effect), while lineage properties come only from training-time parameters. Zero-variance columns are free eliminations, and one clean single-variable rung is worth more than any correlation.
Applies when
- explaining why lineages differ on a robustness axis
- an eval-side knob (gain scale, power) changes results and invites misattribution
- deciding whether to open a DR rung for an axis never actually varied in training
“8 血统地面 μ 训练带全部钉 (1.0,1.0) 零方差,低 μ 差异与「训没训地面摩擦」无关,是 kd DR 带宽的副产物 … 宽 ≤0.24 → 19.9/19.5/19.5;宽 ≥0.40 → 17.1/15.2/14.6/14.2/12.8, 两组完全不重叠。… 训练 kd 带宽 = 参数轴/血统属性;评测部署 --kd-scale = plant 轴 … plant 轴只能当部署缓解, 不能当归因。… 机制未定, 不入定律。”
train/OMNI_V0_SPEC.md § 4. 地面 μ 鲁棒性 = kd DR 带宽的副产物 (2026-08-08) Ungated phase shaping made standing 42x more expensive than stepping - and the stepping was cooking the hip motors
moving-gate-42x-stand-taxGate every phase/clock-driven shaping term on the command that justifies motion, price the cmd=0 case explicitly during design - and when a reward flaw is sim-only, book it with trigger conditions instead of operating immediately on a working lineage.
Symptom
At cmd = 0 the sim policy never stood still - it stepped in place and crept 0.98 m per 20 s; on the real robot the same lineage's stepping made hip_roll motors run 20 degC hotter than every other joint (43-48 degC vs 25-28).
Context
The arithmetic closed it: the three phase-shaping terms (joint_pos_ref 1.6, feet_contact_number 1.2, feet_clearance_swing 1.6) are driven by the gait clock with NO command gating, so standing at cmd=0 forfeits 3.32/step of shaping while honest standing earns only 0.078 of tracking - stepping wins 42x. The heat chain: perpetual stepping = perpetual single support = one hip_roll stalled at ~4.3 N*m (25% of torque limit) carrying the torso's frontal-plane moment - two hip_rolls = 90% of whole-machine steady-state I2R; measured stand-vs-step comparison: total heat -71% when actually standing. The suspended test acquitted the actuator (0.21 rad sag -> 0.0008 rad in air) and mechanics vetoed the easy fix ("降 kp 救不了热" - equilibrium torque equals the external load regardless of kp). The fix (moving_gate: hard-gate the three shaping terms on |cmd| > eps) was designed - then DEFERRED by the user because the real robot at the time stood fine: "真机不表现该问题, 为真机不存在的病改奖励表不划算", with written trigger conditions (C-ladder stand row persistently failing, or real robot starting to step/drift at cmd=0) and the known hazard tag (this is exactly the reward-change class that triggers the B-arm signature). When the real robot later DID step and cook, the booked trigger fired and moving_gate moved from debt to to-do with its benefit re-priced: "停止空烧 hip_roll,稳态发热降 ~71%".
Change
moving_gate designed with the gate_by_cmd convention; deferral, triggers, and expected heat recovery all pre-registered instead of patching the reward for a then-sim-only symptom.
Outcome
The cmd=0 stepping went from mystery to closed arithmetic; the thermal measurement (hip_roll +20 degC) quantitatively confirmed the 90%-of-heat prediction; the reward change waited for real-world justification instead of spending a risky revision early.
Mechanism
Clock-driven shaping terms define a perpetual-motion bounty unless gated by command; the resulting idle gait is not a training bug but the table's optimum. Its cost surfaces on hardware as stall-torque heating set by statics (mass x lateral offset), which no gain change can remove - only removing the motion (gating) or widening the stance can.
Applies when
- the policy steps in place or creeps at zero command
- specific joints run hot in idle behaviors
- deciding when a known reward flaw justifies a risky mid-lineage fix
“塑形合计 −3.32/步 … 净: 站定亏 42 倍 … 两颗 hip_roll 4.29 / 4.09 N·m(各占限扭 25%),占全机稳态 I²R 的 90% … 吊挂实测 hip_roll 跟踪误差 0.21 rad → 0.0008 rad … 降 kp 救不了热 … 真机不表现该问题, 为真机不存在的病改奖励表不划算”
train/README.md § C1 FAIL 节 (cmd=0 的 sim/真机分歧记账) / C2 真机 A/B 三b 发热定性 Fall recovery was defined as the whole chain - any fallen pose, a stable stand, a clean hand-back to walking - and built as a second policy behind a deploy-side switch, not folded into the walking PPO
recovery-two-policies-and-a-state-machineDefine a recovery skill by the whole chain it must complete, including the hand-back to the next controller; if it is built as a separate policy, make the switching logic and its handoff contract a deliverable of their own, and keep the recovery observation contract a subset of the locomotion one so a unified policy stays possible later.
Symptom
A walking robot that falls needs a human to stand it back up. The design question on 2026-08-09 was whether to teach getting up inside the existing omni walking policy or beside it.
Context
The user set the goal as "any fallen pose -> stand up alone -> stand stably", and the spec named the real difficulty as the full chain fall -> recovery -> stable stand -> correctly initialised walking history and clock -> walking, making the deploy state machine a first-class deliverable. A unified single policy had a real-robot precedent (arXiv:2605.18611, a state-dependent gate near 37 deg tilt) but was deferred until a recovery policy and an omni policy were each reliable. The line ran on its own branch and worktree with every walk/stand/omni/run config path untouched. The development path copied the G1 learned get-up logic (arXiv:2502.12152): first find any feasible get-up (ugly accepted), then add smoothing, torque and real-robot constraints. The recovery contract kept the base 45-dim observation (command slice held at 0, no gait phase, no frame history - their reasons do not apply to a skill without a clock or a velocity task), so it stays a prefix of the 215-dim omni contract and a later merge is not foreclosed.
Change
Two policies and a deploy-side switch instead of one retrained walking policy; recovery got its own minimal contract (45 dims, full-range action, later the beta-anchored profile) and its own acceptance battery.
Outcome
The split held for the whole line: on 08-14 deploy_policy gained a second (PolicyIO, ONNX) pair behind --recovery-policy, each loaded under its own manifest contract, and the runbook runs stand_v1b or omni_c4_ff800 as the locomotion side with recovery_v3_1p1c. The literature scan of 08-10 found that every verified get-up implementation deploys one end-to-end policy (or softly gated experts) and stages only on the training side - so the runtime state machine here is the walk/recovery switch, not a staged get-up.
Mechanism
A separate policy keeps each reward table single-purpose and lets a proven walking lineage stay byte-frozen; the cost moves to the handoff, where every piece of state one policy leaves behind (history, clock, last action, command) must be reset for the other.
Applies when
- adding fall recovery or get-up to a robot that already walks
- choosing between one unified policy and a switched pair of policies
- designing the observation/action contract of a secondary skill
“先做 recovery policy + omni policy 两个策略,部署侧状态机切换;不把 recovery 硬塞进现有 omni PPO。 … 任务定义:**任意跌倒姿态 → 自己站起来 → 稳定站立**。真正的难点不只是"起身", … omni walk**(§6 部署状态机是本 spec 的一等公民,不是附录)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §0 目标口径与架构判决(用户 2026-08-09 定) The advisor's "runtime five-stage state machine + per-stage reference poses + RL residual" appeared in none of the three papers it cited - reading the originals changed the plan and downgraded two widely repeated industry claims
advisor-paraphrase-vs-paperRead the primary source behind any piece of advice before adopting its architecture; record where the paraphrase and the original differ, downgrade claims the originals do not support to speculation, and adopt what the verified sources actually share.
Symptom
After the violent first real run, an advisor proposed re-architecting recovery as a runtime staged state machine with reference poses and an RL residual, citing HoST, HumanUP and StableMimic.
Context
The three papers were read in full on 2026-08-09 and tabulated (deployment form, what the "stages" really are, hard constraints, references). HoST: one end-to-end policy, height-gated rewards in training, action anchored as q + beta*a with a beta curriculum. HumanUP: two training stages with the same observation/action; the vendor's three-stage state machine is the baseline it beats (41.7% vs 78.3%); Stage II tracks an 8x slowed Stage I trajectory (4x too violent, 10x does not converge). StableMimic: a learned soft gate. On 08-10 more sources were checked the same way: the Agility page does not say Digit's self-righting was learned in simulation (only step recovery is stated as RL), so the claim was downgraded to speculation; HoST's support for the 12-DoF armless Mini Pi exists in its code repository, not in the paper text.
Change
Adopted only what the originals share: a hard action bound or anchored action space, strong smoothing including a second-difference term, a slowed hidden reference, heavy DR and real fallen states. The staged runtime state machine was not adopted.
Outcome
The next re-rooting candidates came straight from the verified material, and the beta-anchored action space (HoST, with the Mini Pi configuration as the nearest real-robot precedent) became V2, the lineage that later stood up on hardware.
Mechanism
A paraphrase compresses a paper into the advisor's own architecture; only the original shows what was actually deployed, what was a baseline, and which numbers came with which ablation.
Applies when
- an advisor, agent or summary proposes an architecture with citations
- an industry claim ("X learned it in sim") is about to justify a design
- several papers are cited for one combined recipe
“⇒ **顾问的核心形态"runtime 五阶段状态机 + 每阶段参考姿态 + RL residual"在三篇引文 里均不存在**,其中 HumanUP 还点名 state machine 是局限。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §26 三篇引文精读判决(2026-08-09 全文核对;顾问转述与原文有出入) Verify changes in the run's resolved config (and checkpoint md5), never in the source you edited
resolved-config-is-source-of-truthAttribution and single-variable claims must be made on the resolved per-run config (and checkpoint hashes), not on source diffs; verify every intended variable landed before burning compute, and verify every rollback byte-level against the historical resolved config.
Symptom
An intended arm-B config change never reached the training run - the run was grid-identical (117/117 cells) to its C2 predecessor - and the burn was only understood afterwards.
Context
The repo's discipline hardened around the logged resolved config (logs/<run>/params/env.yaml) as the only source of truth: (1) the C2 root-cause analysis was performed against the checkpoint's logged env.yaml, not the code ("以真相源 23-19-25/params/env.yaml 核实"); (2) C4 added a pre-flight: grep the landed env.yaml for the new keys, and compare the first checkpoints of the two arms - identical md5 means the variable did not land, stop immediately; (3) the C4 full rollback was accepted only after starting a 1-iter run and byte-comparing its resolved env.yaml against the historical 700-era file (identical except 4 dormant schema fields, each verified to be at its no-op default).
Change
Standing pre-flight and post-change verification: dump/diff the resolved config that the run actually consumed; use checkpoint hash equality as a cheap "variable landed" detector between arms.
Outcome
Caught the not-landed variable class of failure; made the rollback provably equivalent to the historical training state rather than believed-equivalent.
Mechanism
Between edited source and the running experiment sit layered overrides, env-var switches, and registration logic; only the resolved, serialized config reflects their composition. Diffing at that level tests the actual experiment; diffing source tests intent.
Applies when
- launching an A/B pair or any single-variable rung
- rolling back to a historical training state
- a run behaves as if a change was never applied
“开训前先验落盘 cfg（上一轮臂B 的改动没进 run，与 C2 逐格 117/117 相同）：grep -E "base_com|joint_friction|push_robot|track_lin_vel_y_exp" logs/<run>/params/env.yaml 另：两臂第一个 checkpoint 的 md5 若相同 = 变量没进去，立刻停。”
train/C_LADDER_RUN.md § 3d. ⚠️ 开训前先验落盘 cfg / 3l. 回退清单（验证） After installing the measured plant, re-run all generations paired on old and new plant - identity metrics carry verdicts, physics metrics re-baseline
plant-swap-invariants-vs-shiftsTreat every plant upgrade as an era boundary: re-run the retained policy set paired (same seeds/flags) on both plants, carry forward only verdicts whose metrics proved plant-invariant, re-baseline the rest - and mine the systematic shifts as measurements of the old plant's biases.
Symptom
With the plant finally fully measured (weighed masses 9.792 kg, bench-identified armature, in-situ friction), no historical sim number was comparable to new runs - "历史 sim 数字跨纪元不可比" - and it was unknown which historical verdicts still held.
Context
The era-2c cross-test ran all seven walk generations on the complete plant under one harness (14/14 survived), then re-ran the same 14 configurations on the OLD plant retrieved from git, same flags and seeds, with a self-check (one historical record reproduced digit-for-digit). The split was clean. Policy-identity metrics moved essentially zero across the plant swap - dominant frequency (v7's period-doubling 1.20 -> 1.20), knee amplitude (9.9 -> 10.0), foot distance (+/-2 mm), saturation (100 -> 100, 0 -> 0) - so all seven cross-generation verdicts (freeze signature, saturation-line closure, knee-collapse location, slip-penalty accounting, N2 lineage, v6's balance, v11's triad) were re-confirmed on the honest plant. Plant-physics metrics shifted systematically with ordering preserved: slip down 10-25% (measured friction makes ground-twisting costlier), landing vertical velocity down 15-50% ("旧 plant 高估落地 凶度"第二次独立证实), landing force mixed (mass up 2.2% vs friction braking the swing - two effects fighting). Exactly ONE behavior-level change: v8's low-speed period-doubling vanished (1.30 -> 2.50, lift normalizing) - confirming it had been machine-dependent bifurcation-edge behavior that armature+friction push off the knife edge, while v7's period-doubling stood untouched: saturation-freeze-driven, a policy property, not a numerical accident.
Change
Era re-baselining protocol: after any plant upgrade, one paired same-seed sweep of all retained generations on old and new plant; verdicts keyed to identity metrics carry over, thresholds re-read against the new-plant table, and the differences themselves become plant-physics findings.
Outcome
Seven verdicts survived with evidence rather than assumption; two causes of the period-doubling family were separated with plant-side proof; and the sim's landing-violence overestimate was independently confirmed a second time.
Mechanism
A policy's structural properties (frequencies, amplitudes, frozen joints) are functions of its weights and survive plant changes; contact-mediated quantities are joint properties of policy and plant and shift when the plant becomes honest. Pairing seeds across plants isolates the plant's contribution exactly, so the sweep both validates history and measures what the old plant had been lying about.
Applies when
- installing measured masses/armature/friction into the sim
- historical thresholds are cited across a plant change
- a hardware-only behavior might be bifurcation-edge sensitivity
“策略身份指标逐位不动:主频(v7 1.20→1.20)、膝摆 … 这些是策略属性,plant 换代携带无损,历史定论因此全部成立。… 唯一行为级变化:v8@0.15 的倍周期消失(主频 1.30→2.50…)——印证当时"分岔边缘、机器相关"的判定:armature+摩擦把 v8 推离刀锋;v7 的倍周期纹丝不动(1.20→1.20),它是饱和冻结驱动的深层属性,不是数值巧合。”
train/README.md § 纪元 2c 全代同机横测 (2026-08-04): 完全体 plant 上历史结论全部存活 Write each config's expected hardware signature before the session - and if reality disagrees, change the books, not the conclusion
preregistered-real-expectationsBefore hardware runs, write per-config expected signatures and the disagreement rule (hardware outranks sim; discrepancies get recorded, not reconciled); validate the harness by checking it reproduces at least one known real behavior.
Symptom
Hardware impressions are easily narrated after the fact; without written expectations, any real-robot outcome can be made to "match" the sim story.
Context
The S2 acceptance sheet carried a section titled "sim 侧预注册预期 (事后核对, 不许事后改)" - per-configuration behavioral signatures written before the session: s1e@0.8 the disturbance king (push 159/160, zero chirality, all-mu 20/20) at the cost of speed gates 0/20 and zero-command wander ~0.98 m with -29.5 deg/20 s rotation; fric-3000 "walks accurately but is easier to push over"; fric-2400 neither. Credibility check included: the sim harness had reproduced the already-recorded real behavior (pace in place + right drift + net rotation -30 deg/20 s), which "提高本单全部预期的可信度". The anomaly clause fixed the epistemics in advance: if results systematically disagree with sim, "不改结论改账" - don't massage the conclusion, write the discrepancy into the books, and per the earlier zero-warning lesson, hardware wins.
Change
Every hardware session ships with a pre-registered expectation table (signature per config), a baseline-match credibility check, and a written precedence rule for disagreement.
Outcome
The A/B session became falsifiable: agreement confirms the proxy, disagreement is booked as a proxy-bias finding rather than argued away.
Mechanism
Pre-registration converts qualitative hardware sessions into tests of the sim-to-real mapping itself; a reproduced known behavior calibrates trust in the remaining predictions; and fixing "who wins on disagreement" beforehand prevents authority from drifting to whichever source flatters the plan.
Applies when
- planning any hardware acceptance or A/B session
- the sim harness's credibility in this regime is unestablished
- post-session write-ups tempt narrative fitting
“⚠️ sim 复现了真机已记录的「原地踏步 + 右漂 + 净旋 −30°/20s」—— harness 与真机行为对得上, 提高本单全部预期的可信度。… 结果与 sim 系统性不符 → 不改结论改账: 写进 README 该节, 按 「Isaac 指标三次零预警」的教训, 以真机为准。”
train/REAL_RUN_S2.md § 2. sim 侧预注册预期 (事后核对, 不许事后改) / 4. 异常处置 Order hardware runs by sim risk, gate each stage on the last, and put the fragile cell last with a spotter
risk-ordered-real-deploymentScript hardware sessions as a risk ladder: baseline first, sim-riskiest last with a spotter, suspended smoke before ground, each stage gated on the previous, environment (floor mu) recorded as a selection input - and stop at the stage that misbehaves.
Symptom
Five policy-x-gain combinations had to go on hardware in one session, with sim survival ranging from 20/20 down to 17/20 (and zero-command survival down to 2/20) - an unordered session risks breaking the robot on an avoidable run.
Context
The execution sheet fixed the order as sim-risk low to high, control baseline first (current SOTA establishes the floor reference), the fragile cell (fric-2400@kd1.0) last with a person spotting throughout. Stage gating: suspended smoke (feet off ground, 10 s each, all five pass before anything touches down) -> suspended with IMU and forward command (gait forms in the air) -> grounded runs -> speed raise only for combos that survived the previous stage -> zero-command tests only with a spotter, ordered by sim zero-cmd survival, with the 2/20 cell skipped by default. Preconditions include recording the floor material and estimating mu (if mu <~0.6, sim says pick the kd1.2 gain as main), port/CAN self-check, calibration frozen. Any stage failing stops the session at that stage: "任一段出问题就停在那一段, 不要跳到下一段".
Change
Session structured as a risk ladder with per-stage gates instead of a flat checklist; per-combo sim survival numbers written into the run table as the ordering key.
Outcome
The session design localized any failure to the cheapest stage that could reveal it, kept the robot safe for the informative fragile run, and made the control baseline available before any comparison run.
Mechanism
Hardware sessions consume a shared budget (robot integrity, battery, floor time); ordering by predicted risk means information is bought cheapest-first, and stage gates convert an expensive failure into a cheap earlier one. Baselines run first because every later reading is relative to them.
Applies when
- taking multiple policies/configs to hardware in one session
- a candidate is known-fragile in sim but must be measured
- writing a deployment runbook for a new robot
“跑序 = sim 风险从低到高, 最险的放最后 (依据 = 存活门/零指令存活) … ⑤ 是 sim 里最脆的一格 … 放最后跑, 全程留人扶, 起步即给 cmd, 零指令不做。… 任一段出问题就停在那一段, 不要跳到下一段。”
train/REAL_RUN_S2.md § 上机名单 / 全部命令 An outer heading P-loop at deploy cut drift 10x because its output stays inside the trained command band - then training was aligned to it
deploy-heading-loop-and-align-trainingFix drift-class problems first with an outer loop whose output provably stays inside the trained command band; when adopting it permanently, align the training command generator to the deployment's actual command mixture (feedback-driven AND constant), matching law, gain, and clip exactly.
Symptom
Persistent heading drift on straight-line walking (v6 net yaw 60.3 deg over 15 s) that reward-side fixes had only partially tamed.
Context
The deploy stack added --heading: an external P loop wz = clip(0.5 * wrap_to_pi(theta0 - theta), +/-0.6), recomputed each frame and fed into the policy's ordinary wz command slot. Measured: net yaw walk_v6 60.3 -> 5.8 deg, walk_v5 17.4 -> 4.2 deg. A run-level audit later corrected the mechanism story: training had heading_command=False since v1 - the policy had NEVER seen heading-error feedback, so the loop works purely because its output lands inside the trained command distribution wz ~ U(+/-0.6): "收益真实,当时的机理解释写错了" (the benefit is real; the mechanism explanation had been wrong). v8 then closed the loop properly: training-side heading command enabled with rel_heading_envs=0.5 - half the envs get heading-error-driven wz, half get explicit constant wz, because deployment feeds wz BOTH ways (straight-line = heading feedback, turning = constant command) and rel=1.0 would have made constant-wz turning out-of-distribution. The law, gain, and clip were aligned item-by-item between trainer and deploy tool.
Change
Deploy-side outer loop first (no retrain needed); then v8-D enabled the matching training-side heading command at rel=0.5 with identical gain (0.5) and clip (+/-0.6), contract unchanged (wz slot carries the computed value).
Outcome
Drift handled at deploy (5.8 deg) generations before training caught up; the alignment removed the residual train/deploy distribution mismatch, with the accepted cost booked (open-loop straight walking becomes more OOD for heading-envs - irrelevant since acceptance and deployment always run the loop).
Mechanism
A learned velocity-tracking policy is a valid inner loop for any outer controller whose commands stay within the trained command distribution - the policy needs no knowledge of the outer objective. Full alignment then requires training on the same mixture of command sources the deployment actually uses, in the observed proportions.
Applies when
- heading/position drift on a velocity-tracking policy
- designing outer loops over learned locomotion controllers
- training command distribution differs from how deployment feeds commands
“审计更正(2026-08-02,run 级 env.yaml):训练侧自 v1 复盘起就是 heading_command=False … 策略从未见过航向误差反馈。--heading 是评估/部署侧外加的航向 P 环(wz=clip(0.5·err,±0.6), 落在训练分布 wz~U(±0.6) 内)。实测净偏航 walk_v6 60.3° → 5.8° … 收益真实,当时的机理解释写错了”
train/WALK_V7_SPEC.md § 0. 本轮之前已经改掉 (航向闭环, 含审计更正) The median of a bimodal metric lands in the empty gap - check the distribution, and never judge swing on 3 seeds
median-hides-bimodal-distributionBefore quoting a median or mean, look at the distribution; report suspected-bimodal metrics as mode share plus per-mode ranges, use small-seed smoke runs only to screen trends, and size the seed count for decisions by the share resolution you need (here: 20).
Symptom
Years of "high swing variance" and undecidable 3-seed swing readings turned out to be one fact: the metric was bimodal all along - "历代 swing 高方差与 3-seed 不可判由此定性:一直在测双稳态系统" - and every median reported from it (e.g. 12.1 mm) described a value no seed ever produced.
Context
Concrete instances: s2e_pd-1400's 20 seeds split 2.6-4.9 mm vs 19.3-24.0 mm with zero seeds between; s1e-500 read 3.9 mm on seeds 0-2 but 23.1 mm median over 20 seeds; a 3-seed reading of 19.3 was logged as "double-peak optimism, lesson recurrence #4". The selection re-audit codified the sampling rule: "3-seed 的 swing 读数不可判点, 只能筛带,选点必须 20-seed" - 3 seeds may screen a band, only 20 seeds may pick a point.
Change
Swing (and any suspected multi-modal metric) reported as mode shares plus per-mode ranges instead of a bare median; 3-seed smoke numbers demoted to band-screening; all shipping/selection decisions moved to 20-seed batteries.
Outcome
The "swing debt" bookkeeping was reinterpreted as basin probability (see swing-bistability-damping-switch), and checkpoint selection stopped being whipsawed by which basin the first three seeds happened to fall into.
Mechanism
Central-tendency statistics presuppose unimodality; on a bimodal distribution the median tracks the mode SHARE, not any achievable behavior, and small samples alias the share entirely. Mode-aware reporting (share + per-mode stats) is the only faithful summary, and the needed sample size is set by the share resolution required.
Applies when
- a quality metric shows chronic high variance across seeds
- 3-seed smoke readings contradict 20-seed batteries
- reporting swing height, clearance, or any basin-prone metric
“中位数落在空档里,「swing 债 −11mm」实为「50% 概率掉进拖地吸引子」。历代 swing 高方差与 3-seed 不可判由此定性:一直在测双稳态系统。… swing 跨 seed 双峰 (500 在 seed0~2 只读 3.9mm, 20-seed 中位 23.1) —— 3-seed 的 swing 读数不可判点, 只能筛带, 选点必须 20-seed。”
train/README.md § swing 双稳态定性 / s1e 选点重审 Four in-lineage attempts to widen the standing stance failed - remove a tax, add a joint-space knife, change the target, add a task-space metric penalty - because the stance was the end state of the get-up path; trained from scratch with the right terms it grew right from day one
stance-decided-by-get-up-pathA posture a skill ends in is shaped by the path the policy takes to reach it; if several single-variable edits to the terminal-phase reward cannot move it, stop editing that phase and retrain with the terminal constraint present from the start.
Symptom
v2_6c stood with its feet 0.159 m apart (task-space) and its hips yawed 45-47 deg the same way, which split on the real robot. Standing-phase reward edits did not move it.
Context
V2.7-A removed the flat-feet tax on compensated stances (stance unchanged); V2.7b added a hip-roll lower-bound hinge (+5 deg in 3,000 iterations, yaw ratchet); V2.8 changed the stand_pose target to a wide flat stance (stance unchanged, yaw not unwound, feet nearly overlapping, mu 0.4 transfer 2%); V2.9 penalized lateral spacing in metres (the policy parked just outside the penalty's gate in a lunge, 0% success). The v2_6c get-up goes through a split and closes the feet together as it rises.
Change
In-lineage stance surgery was formally closed. V3.1 trained from scratch with task-space stance terms present from the first iteration (and, after P1, a positive width band instead of a penalty).
Outcome
V3.1 P1b: lateral stance 0.364 m, foot tilt 0.0 deg, all four categories 100%, MuJoCo mu 1.0 and 0.4 both 100% - with a symmetric toe-out the kinematic audit had not enumerated. P1c (with a yaw guard): 0.355 m, all six acceptance criteria passing, mu 1.0-0.4 all 100%; it became the product.
Mechanism
A converged policy does not rebuild the path that produced its terminal posture; a standing-phase gradient only finds the nearest hack around the posture the get-up delivers.
Applies when
- the final posture of a transition skill is wrong and resists terminal-phase shaping
- repeated continuation rungs produce hacks instead of the intended posture
- deciding between another in-lineage fix and a from-scratch retrain
“窄站距 + yaw 扭是 v2_6c 起身策略(劈叉起身 → 双脚并拢收势)的**结构性 终态**,不是站立段的孤立参数 —— 站立形态由起身路径决定,在血统内只动 站立段奖励改不动它。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §44 结果:V2.8 判 FAIL —— 血统内站姿手术第三次证伪 The +/-50 mm lateral COM randomization meant to spread the legs coincided with legs pulling IN - rolled back per its own pre-registered contract
com-dr-rollback-on-symptomWhen adopting a DR value that covers no local measurement, write its intent and rollback trigger into the config at adoption time; roll it back as the control arm the moment the symptom contradicts the intent, and promote the symptom's metric into the acceptance battery.
Symptom
After v7 adopted the reference developer's oversized lateral COM randomization (+/-50 mm) explicitly to force leg spread, the real robot's legs narrowed instead - lateral mean 154 mm / closest 107 mm in sim (nominal 214.5), narrower still on hardware with occasional leg contact.
Context
The rollback was clean because the adoption had been honest: the robot.yaml comment recorded the intent AND that the +/-50 value covered no local measurement (only a 16/7 mm measured offset existed; even the prior widening to +/-20 was subjective), plus the reference's own reported side effect (base sway) and the note "这一项要单独跑、 单独归因". When the opposite symptom appeared, v8 returned y to +/-20 mm as the control arm ("要么没起作用、要么帮了倒忙 … 按约定退回做 对照"), kept x/z untouched (a noise-level difference not worth another variable), and named the second suspect: the landing penalty itself, via the reference's own three-link chain (landing penalty -> stance narrows -> spacing penalty needed). A gate lesson was booked in the same table: v7's sim numbers had ALREADY crossed the line (154/107 vs v5's 182/147) - "这个指标本可拦下 v7" - so foot-distance became a standing acceptance row (min >120 mm, zero leg-leg contacts).
Change
base_com_offset_m y: 0.050 -> 0.020 (x/z kept), regenerated through the export tool rather than hand-editing derived files; foot-distance acceptance row added.
Outcome
A borrowed DR lever with no local measurement basis was retired the moment its symptom contradicted its purpose, at single-variable cost; the metric that would have caught it pre-hardware entered the gate.
Mechanism
DR ranges shape behavior through the policy's robustness strategy, which is jointly determined with every reward term; a lever that forces stance width on one robot can be dominated by a stronger narrowing pressure (landing softness) on another. Levers adopted without local measurement must carry their own rollback trigger, because there is no nominal to argue from when they misbehave.
Conflicts
Causality is not fully closed in the source: the narrowing may come from the landing penalty rather than the COM lever ("腿距的第二嫌疑人是 ④ 本身"); the rollback is the pre-agreed control experiment, not a verdict that the lever caused the narrowing.
Applies when
- importing DR ranges or behavioral-forcing randomizations from references
- a DR lever's observed effect contradicts its documented purpose
- a sim metric existed that would have caught a shipped regression
“⑥ 的本意 … 是逼策略把脚分开;真机结果是脚向内收且偶发相碰——要么没起作用、要么帮了倒忙。… 注释当时就写了"这一项要单独跑、单独归因"。现在症状出现了,按约定退回做对照。”
train/WALK_V8_SPEC.md § 3. 改动 C — 质心随机化退回(撤销 v7-⑥ 的 y 项) Adapting a lineage to one plant increment needs hundreds of iterations, not thousands - long runs only buy specialization
continuation-budget-not-from-zeroBudget continuation rungs by increment class (hundreds of iterations for plant pins and smooth shifts, ~1000-1500 only for behavior-demanding changes like push), enforce a hard cap with frequent evaluation, and treat remaining budget as a reason to stop, not to continue.
Symptom
The default "6000 iterations per rung" (a from-zero-scale budget) was about to be applied to continuation rungs whose only change is one plant/DR increment - overspending compute and, worse, giving each rung thousands of iterations to specialize away retained skills.
Context
The 2026-08-07 budget table replaced the default with "最低适应窗口 + 每 100 iter 验收 + hard cap" scaled to the increment's difficulty: fixed-latency levels 300-500 (cap 500-800; the base has already seen in-band values, this only pins the plant); PD full-band 700 (cap 1000; kp+/-20%/kd+/-30% clearly widens the actuator family); COM +/-20 mm 500 (cap 800; a smooth dynamics shift); friction DR 700 (cap 1000; contact and actuator friction change the gait/contact solution together); push 1000 (cap 1500; a non-static plant change requiring recovery behavior - hardest). Rationale: "续训适应一个 plant 增量不需要从零量级的预算,跑长了只是给特化时间". The C ladder reused the scheme (per-rung caps 500-2000 by increment type), and the deep-training hazard got its own name when long runs sold quality ("深适应卖质量" - deep adaptation sells quality).
Change
Per-rung iteration budgets set by increment class with hard caps and 100-iter watch loops; checkpoint selection inside the window by the smoke curve, never "run to cap because budget remains".
Outcome
S2/C rungs completed in 300-1500 iterations each; the recurring late-run degradations (collapse valleys at 1500+, vx+0.30 decay) fell outside most rungs' caps instead of inside their runs.
Mechanism
A continuation rung's learning problem is local robustification around an existing optimum - low sample complexity; iterations past adaptation are spent sharpening onto the current distribution, which is exactly how retained skills and margins erode. Budgets sized to the increment bound both compute and the specialization damage window.
Applies when
- planning iteration budgets for a robustification or command ladder
- a continuation run keeps improving its training metric late
- retained skills decay in the back half of long continuation runs
“「最低适应窗口 + 每 100 iter 验收(watch_ckpt --every 100)+ hard cap」—— 续训适应一个 plant 增量不需要从零量级的预算,跑长了只是给特化时间 … ⑥ push | 1000 | 1500 | 非静态 plant 变化,要学 recovery 行为,最难”
train/OMNI_V0_SPEC.md § 4. 每级 iter 预算(2026-08-07 用户定) Record where every failed episode ends - an end-state confusion matrix showed all failures finishing seated and overturned a "cannot roll over" diagnosis that per-category success rates hide by construction
end-state-confusion-matrixFor any multi-category acceptance, report where each failed episode ends, not only which category it started in; it costs a few lines and no extra simulation, and it separates "cannot reach the goal" from "reaches the wrong basin".
Symptom
Prone scored 0% for three generations; the working diagnosis was "prone lacks the roll-over skill", and R0.3 spent a run adding prone-to-side roll-arc start states. It bought nothing: the 45-deg roll band itself only moved from 24.2% to 26.6% after 3,000 iterations.
Context
Acceptance reported success per starting category. A final-state table (lying prone / on the side / supine / seated / standing for every failed episode) was added to accept_recovery.py at R0.3.
Change
The confusion matrix became a permanent part of the acceptance output, and the prone diagnosis was rewritten from it.
Outcome
The prone, side and supine columns were all zero - every failure ended seated - and prone had righted its torso in 159/159 episodes (tilt under 30 deg in 100%). The missing ability was standing up from one specific seated configuration, not rolling over, which redirected the next rungs to foot placement and to a configuration probe.
Mechanism
Per-category success rates collapse "reached the wrong basin" and "never reached anything" into the same zero; the end state separates them.
Applies when
- a category sits at 0% and the diagnosis rests on its label
- recovery, manipulation or navigation tasks with distinct terminal states
- an intervention aimed at the presumed cause shows no effect
“**① 末态混淆矩阵 —— 固化(已在 `accept_recovery.py`)。** 它给出的 "趴/侧躺/仰躺三列全 0、所有失败都终于坐姿"是本线最改变决策的一个事实, 而**逐类成功率按构造看不见它**。 … 成本十来行、零额外仿真。 … **② prone 病因更正(旧诊断作废)。** 旧:"缺翻身"。新:**prone 159/159 全部 把躯干翻正**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §15 R0.3 判决 + 三件事的判断 The 1.5 Hz step-frequency gate was retracted - the author had misread his own actuator data, and the limit fought pendulum dynamics
gate-threshold-retracted-frequencyEvery gate threshold must cite its measurement and survive a first-principles sanity check; when a gate keeps failing otherwise healthy behavior, re-derive the threshold from the raw data before enforcing it again - and retract wrong gates in writing.
Symptom
An acceptance criterion "step frequency <= 1.5 Hz" kept failing healthy policies (walk_v4 at 2.33 Hz), and an earlier attempt to force slower stepping (v3) had killed stepping altogether.
Context
The threshold had been derived from the author's own actuator frequency-response measurements - but re-reading the raw table showed the misread: amplitude ratio at 2.0 Hz is 0.88 (knee) / 0.83 (ankle), acceptable; the genuinely bad point was walk_v2's 3.8 Hz at 0.58. Mechanism check agreed: the leg as a compound pendulum (L ~ 0.30 m) has a natural frequency ~1.1 Hz, swing half-period 0.45 s - the observed 2.1-2.4 Hz sits near where the leg wants to swing, and forcing 1.5 Hz "是跟摆动动力学对着干" (fights the swing dynamics). The frequency definition itself was pinned by two independent methods (contact-event counting 2.39 Hz vs FFT 2.33 Hz, agreeing): reported numbers are cycle frequency = steps per leg per second.
Change
Gate retracted in writing: "步频 ≤1.5 Hz 应删除或放宽到 ≤2.5 Hz"; frequency definition standardized before entering any config.
Outcome
walk_v4/v6's 2.1-2.4 Hz reclassified from disease to normal; the v3 failure got its probable explanation (suppressing stepping to meet a wrong gate).
Mechanism
A gate is only as good as the measurement and the reading behind it; thresholds inherited from a misread plot become invisible design constraints that later training obeys at real cost. Cross-checking a threshold against first-principles dynamics (pendulum frequency) is a cheap way to catch such misreads.
Applies when
- an acceptance threshold repeatedly fails policies that look healthy
- thresholds were set from a single person's reading of raw data
- a forced compliance with a gate degrades the behavior it guards
“我当初依据自己测的执行器频响定的,但看错了区间。… 2.0~2.4 Hz 的幅值比 0.83~0.88 是可接受的;真正不行的是 walk_v2 的 3.8 Hz。… 腿按复摆算(L≈0.30 m)自然频率约 1.1 Hz … 把它压到 1.5 Hz 是跟摆动动力学对着干(walk_v3 把迈步压没了,可能正是这个原因)。”
train/WALK_DIAGNOSIS.md § ② 撤回"步频 ≤1.5 Hz"这条验收标准 —— 是我定错了 Multiple changes may share one rung only if their symptom spaces are orthogonal - with the ablation order written in advance
orthogonal-batch-with-ablation-orderBatch changes into one rung only when you can name each change's private symptom space in writing; pre-register the ablation order (numeric before structural) and per-change escalation plans, so a mixed outcome decomposes without new decisions.
Symptom
v8 needed four repairs at once (saturation cheating, landing impact, leg narrowing, heading alignment) - strict one-variable laddering would have cost four training cycles for wounds that were all already diagnosed.
Context
The batch was allowed because each change owns a disjoint symptom space, stated explicitly: "A→形态/饱和, B→落地/步态高度, C→腿距/roll 摇摆, D→偏航/转向" - so a single run can attribute each outcome to its change by which symptom moved. For the failure case, the ablation order was pre-registered (A2 -> A1 -> B -> D -> C, "先撤数 值改动" - retract numeric tweaks before structural ones), and every change carried its own escalation/rollback plan (e.g. A insufficient: joint_pos_ref 1.6->2.0 or widen the exp kernel; B overdone - robot afraid to land: v_ok 0.30->0.45; D unstable: rel 0.5->0.25, not back to 0).
Change
Four-change rung executed as one run with per-change symptom ownership, per-change contingency plans, and a pre-registered global ablation order for unattributable regressions.
Outcome
The rung retained single-run attributability without paying 4x training cost; the contingency table meant no failure mode would require improvising an ablation under pressure.
Mechanism
The one-variable rule exists to keep attribution possible, not as an end in itself; attribution survives batching exactly when the changes' observable effects are separable. Orthogonality is a claim that must be argued per pair in advance - and the pre-registered ablation order is the escape hatch for the case the claim fails.
Applies when
- several diagnosed fixes are queued and ladder time is scarce
- deciding between strict laddering and a combined rung
- a combined rung shows a regression no single change explains
“四个改动症状空间基本正交,可单 run 归因:A→形态/饱和,B→落地/步态高度,C→腿距/roll 摇摆,D→偏航/转向。出现无法归因的整体退化时消融顺序 A2→A1→B→D→C(先撤数值改动)。”
train/WALK_V8_SPEC.md § 8. 风险与归因 An edge-triggered landing penalty missed the tail and fired after the harm - penalize overspeed continuously inside the contact window
penalize-tail-before-touchdownPenalties aimed at impact/violation events must (a) price the excess over a threshold, not the mean, and (b) be active on the approach (state-gated window), not triggered by the event - check your control rate can even see the event you are penalizing.
Symptom
The v7 landing penalty (vz^2 on the contact-force rising edge, weight -10) did not bite: landing-velocity 95th percentile stayed at 2.61 m/s against a 0.3 target.
Context
Two structural faults were identified: (1) it penalized the MEAN over sparse events - many soft landings dilute the occasional violent slam, while the damage (GRF peaks, motor peak load) lives in the tail; (2) it fired AFTER touchdown - at 50 Hz evaluation the rising edge is aliased by physics decimation, so the read vz is often the already-decelerated post-impact value: underestimated, and with no shaping gradient before contact. Replacement: continuous penalty while the sole is inside a height gate (h < 0.03 m): relu(-vz - 0.30) - only the excess over an allowed approach speed is penalized (tail only), and gradient exists for several frames BEFORE touchdown. The sole-height computation again subtracts the 0.0585 m link offset ("WALK_DIAGNOSIS 坑#1, 别再踩"); the edge-triggered version was kept as a diagnostic only.
Change
feet_landing_vel reformulated: edge-event vz^2 -> in-window relu(-vz - v_ok) with v_ok 0.30 (conservative vs the sqrt(L)-scaled human value ~0.19, to be tightened after passing), h_gate 0.03, weight unchanged -10.
Outcome
The failure analysis of the first form was written before the second was trained; the v_ok escalation path (0.30 -> 0.45 if the robot becomes afraid to land) was pre-registered in the risk table.
Mechanism
Sparse-event mean penalties optimize the average case while the constraint is a quantile; and any penalty evaluated only at/after a discrete event gives the optimizer no gradient along the approach trajectory that determines the event. A state-gated continuous excess penalty fixes both: it prices only violations and shapes the approach.
Applies when
- impact/landing penalties fail to move tail percentiles
- a penalty is triggered by contact edges at a coarse control rate
- designing constraint-style penalties for rare violent events
“罚的是均值路径:上升沿是稀疏事件 … 大量软着陆稀释偶发猛砸;而伤害在尾部 … 罚在触地后:50 Hz 评一次,上升沿被物理 decimation 混叠,读到的 vz 常是撞完已减速的值——既低估,又没有触地前的塑形梯度。”
train/WALK_V8_SPEC.md § 2. 改动 B — 落地惩罚改罚尾部、罚在触地前 Decompose the offending quantity by channel first - then penalize the failure event, not the joints
penalize-the-slip-not-the-jointBefore penalizing motion to fix a side effect, measure which channels actually carry the offending quantity; prefer penalties conditioned on the failure event that are exactly zero for healthy behavior - and do not medicate behaviors that measurement shows are not sick.
Symptom
Heading drift with support-foot yaw slip (v5: 212-284 deg accumulated over 15 s); the previous v6 draft had attacked it by penalizing lateral joints (a roll 4.0 / yaw 2.0 "home" group) - which collapsed training into the standing basin.
Context
Before choosing the penalty target, the yaw angular momentum was decomposed by joint group with MuJoCo subtree_angmom weighted by real walking joint velocities: pitch-class joints (hip_pitch + knee) carry 95.3%, hip_roll 3.3%, hip_yaw 1.4%. The failed "home" group had been taxing 2.7/step to manage a 4.7% channel. The replacement, feet_yaw_slip (-0.2, |support-foot yaw rate| while in contact), targets the failure event itself and - decisively - costs a non-slipping gait exactly zero, which "横向回家组做不到". The same rung's do-not-do table applied the complementary principle to foot spacing: measured 196-214 mm, stable, no crossing - "没病不吃药" (no disease, no medicine).
Change
Removed joint-usage penalties for the drift problem; added the event-conditional slip penalty (-0.2, realized tax 0.141/step = 12% of tracking) alongside the existing linear-slip term.
Outcome
Turn-gain left/right difference improved 70% -> 19% and heading 185 -> 60.3 deg by v6 without a standing-basin collapse; the 2.7/step lateral tax never returned.
Mechanism
Penalizing joints taxes every use of a channel including healthy use, and if the channel carries little of the offending quantity the tax buys nothing while pushing the optimum toward immobility. An event-conditional penalty (slip while in contact) prices only the failure, leaving the healthy gait's cost surface untouched - and the channel decomposition tells you in advance whether a joint-side fix can even work.
Applies when
- choosing a penalty target for drift/slip/impact problems
- a proposed penalty taxes joints or motions rather than failure events
- a previous joint-penalty attempt collapsed the gait
“pitch 类 (hip_pitch + knee) 占偏航角动量 95.3% … hip_yaw 1.4% … 压 hip_yaw 是管 1.4% 的通道收 2.7/步 的税 —— 上一轮正是这样把策略推进了站立盆地。滑移项不惩罚走路: 不打滑的步态代价为零, 这是横向"回家"组做不到的。”
train/WALK_V6_MINIMAL.md § ① / ② 新增 feet_yaw_slip Prone get-up sat at 0/159 until two gated hinge terms moved the seated feet - first sideways (561 -> 360 mm), then fore-aft (-168 -> +56 mm) - and success went to 158/159 with nothing else changed
prone-dead-end-is-foot-placementWhen a stuck state and a successful state differ geometrically, penalize the discriminating quantity with a gated hinge that is exactly zero in the state the policy actually reaches (measure it - not the nominal), then re-probe: flattening one axis can move the discriminant to another.
Symptom
Prone falls always righted and then sat with the feet splayed wide or tucked behind the hips, from where the policy never stood (0% for four generations).
Context
Four lines of evidence pointed at foot position: the configuration probe (ankles 215 mm apart stood 52.3%, 561 mm apart 0.0%); FK showing the action contract's nominal (a = 0) is itself a 465 mm straddle, so the action_rate and still terms were pulling toward the splits; biomechanics (feet tucked under the body cut peak hip-extension torque 148.8 -> 32.7 N*m, -78%); and HoST's foot-displacement term, which this reward table lacked. The earlier "not a reward hole" reading was corrected to "a gradient hole, not a level hole": at the dead point the heaviest term (upright) was saturated with zero gradient, still paid for not moving, and the one live gradient (base_height) pointed at the thigh-horizontal torque barrier. A prone ROM scan had already ruled out pushing up from prone.
Change
R0.4: feet_spread_excess = clamp(ankle distance - 0.215, 0, inf) x upright gate, weight -2.0, plus a height-decay factor added after measuring that the policy's real standing stance was 406 mm, not the 215 mm nominal (the plain version would have taxed every successful stand 0.38/s). R0.5: the same shape on the fore-aft axis, feet_fore_seated = |fore-aft offset - 0.05| x upright gate x height decay, target +50 mm (the measured natural offset of standing postures). One variable per rung.
Outcome
R0.4: seated ankle distance 561 -> 360 mm, supine/side exactly unchanged, prone 0 -> 1.9%, mid 45.9 -> 62.2%; a probe then showed the discriminant had moved to the fore-aft axis (standing starts +42 to +51 mm, the prone seat -168 mm). R0.5: supine 99.4, prone 99.4, side 100, mid 100%, re-falls 0%; both geometry terms collapsed to ~0 near iteration 13,100 as base_height rose, and the prone fore-aft offset went -168 -> +56 mm - the term's own target, closing the causal chain. The cost, unmeasured at the time: action jitter rose 33% (sum |da|^2 6.82 -> 9.06).
Mechanism
An upright-gated hinge is inert while the robot rolls and exactly zero in the achieved stance, so it adds gradient only inside the stuck basin; a seated robot with its feet behind or outside its COM must make a kinematically unfavourable transition to stand, and moving the feet under the body removes it.
Applies when
- a get-up or transition skill fails from one start category only
- successful and failed episodes differ in a measurable geometric quantity
- a shaping term might tax the posture successful episodes already use
“`recovery_r0_5`,唯一变量 = 追加 `feet_fore_seated`(与 R0.4 同形状,只换测量轴)。 … 对照 R0.4 的 prone(3.1%,360 mm,**−168 mm**):前后偏移从 −168 走到 +56, 正是这一项的目标量,**判别量被消掉后成功率随之到顶** —— 因果链完整。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §20 R0.5(前后向脚位置项):成功率门全过 —— prone 0/159 → 158/159 Removing a foot-spacing wall passed every simulated gate and made the feet collide on the real robot - nothing priced stance width in the two-foot phase, the policy narrowed to the simulator's self-collision floor, and real calibration offsets closed the last millimetres; the wall came back with a gate
removed-wall-returns-on-hardwareWhen a constraint is removed, name what will govern that quantity instead and add a gate for it; never let a simulator's collision floor be the margin, and when a gate is exceeded by a hair, record the exact numbers and hand the release decision to a person instead of quietly passing it.
Symptom
On the first real-robot try of oneleg_v0 (2026-09-16) the two feet collided; the user also judged the folded foot not high enough.
Context
The V0 reward table had dropped the feet_lateral_distance wall because it seemed to conflict with the hip adduction single support needs. In the two-foot command bucket no remaining term governed stance width, so the policy drifted narrower until the simulator's self-collision stopped it; the sim acceptance had no foot-spacing gate, so 40/40 said nothing about it. On the robot, calibration offsets consumed the margin.
Change
V0.1: the wall restored (-10, minimum 0.16 m), re-checked against measured numbers (a swing-phase lateral spacing of ~148 mm costs 0.12 per step, acceptable); fold weight 0.8 -> 2.0; a ninth gate: minimum foot spacing >= 100 mm and zero leg-contact frames. The removal was kept on record.
Outcome
oneleg_v0_1 (V0r2 model_2200) passed 39/40 with the spacing gate 40/40. The single miss (a 15.4 deg tilt transient against a < 15 deg limit during a side switch, steady 6.9 deg, everything else green) was recorded with its numbers and released for the user to overrule.
Mechanism
An unpriced degree of freedom drifts to wherever the simulator stops it; if that stop is the simulator's own collision model, the policy's margin on hardware is whatever the calibration error leaves.
Applies when
- dropping a reward term that looked redundant or conflicting
- hardware shows a failure no simulated gate measures
- a release candidate misses one gate row by a small amount
“V0 撤墙被真机证伪（2026-09-16）：双脚桶没有任何项管站宽，策略贴 sim 自碰撞底线收窄，真机标定偏差一吃**双脚相碰**。 … min ≥ 100 mm 且腿碰 0 帧（eval_straight 同判据）—— … V0 真机双脚相碰暴露 sim 门未看脚距的缺口 … L s2 标称 tilt 瞬态 15.4°（门限 <15, 超 0.4°, 稳态 6.9°, 该跑其余全绿）——换侧瞬态蹭线, 判定放行留档, 用户可否决。”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §4 feet_lateral_distance 行 / §6 验收门 ⑨ / §8 核查单 7 A get-up policy righted itself and sat - three terms paid the seated pose 84% of the return, and the only shaping term that could tell sitting from standing was an exp kernel outputting 5e-5
seated-basin-dead-exp-kernelWhen a policy parks in a degenerate posture, tabulate what each reward term pays that posture against the target (watch contact terms that reward touching rather than bearing load) and evaluate every exp kernel at the error actually observed; a kernel narrower than the real error is switched off, and widening it is a one-variable repair that adds nothing new.
Symptom
R0 converged by iteration 700 and gained 1.7% over the next 2,300; success 0.0% in all four fall categories. Three of four success conditions passed (tilt median 1.0 deg, both feet in contact 99.6%, angular rate low); height passed 0.6% (median 0.204 m against 0.326). The robot knelt in a W-sit: hip yaw +/-47 deg, knees folded to 92% of the hard limit, shins flat, pelvis on the ground, torso vertical.
Context
Minimal reward table: upright (1-g_z)/2 +2.0, base_height linear progress +1.5, stand_pose exp(-||q-q_stand||^2/std^2) x upright gate +1.0 with std 1.0, still +0.5 and feet_on_ground +0.5 both x the upright gate, plus regularizers. The upright gate is a hinge that opens below 30 deg of tilt. The pre-registered fallbacks were then checked against the measured state: tightening the tilt gate was falsified (tilt was already 1.0 deg); a success bonus contradicted the spec's own no-cliff-bounty rule; narrowing the categories was useless (all four converged to the same pose); raising init noise was too weak for a basin this deep. Only a half-rise intermediate state addressed it, and a cheaper repair existed.
Change
R0.1 (user decision, single variable): stand_pose std 1.0 -> 3.0. Not a new term and not a bounty - repairing a declared term that was numerically dead. The two runs' logged env.yaml differ in log_dir and std only.
Outcome
R0.1 58.2% overall (R0 0.0%): supine 91.5%, side 82.2%, mid 55.9%, prone 0/156; knees fully straight; ||q-q_stand||^2 9.99 -> 0.91 and the stand_pose term 4.6e-5 -> 0.90; get-up ~1 s, no re-falls, the curve still rising at the 3,000-iteration cap. Prone stayed at zero and needed a different fix (see prone-dead-end-is-foot-placement).
Mechanism
Sitting earned upright 1.98/2.0, still 0.43/0.5 and feet_on_ground 0.46/0.5 - 3.0 of a 3.57 per-second return - because feet_on_ground asked for contact, not load. The only terms separating sitting from standing were base_height (+0.70/s for standing) and stand_pose, whose kernel at the real 9.99 rad^2 error (75% of it in the two knees) was exp(-9.99) = 4.6e-5 with a gradient near 1e-4. Standing up meant risking 3.0/s to gain 0.70/s while unfolding knees at 92% of their limit under load. With std 3 the same term is exp(-9.99/9) = 0.33 - a live gradient, three quarters of it on the folded knees.
Applies when
- a policy converges early to an upright but low, seated or kneeling pose
- a posture-matching exp term reads ~0 in the training logs
- contact-based rewards saturate while the task metric does not move
“**关键:`feet_on_ground` 只问"触地"不问"承重", 跪坐时双脚确实贴地,照样满分。** 三项 3.0/s = 总回报 3.57/s 的 84%。 … **exp(−9.99) = 4.6e-5** —— 权重 1.0 的项实际输出 5e-5、梯度 ~1e-4, **不是"还没学会",是数值上根本不存在**。 … **R0.1 决定(用户 2026-08-09 定,单变量)**:`stand_pose` 的 `std` **1.0 → 3.0**。 不是加新奖励、不是悬崖悬赏,而是**修复一个已声明但数值失效的项**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §11 R0 首跑(recovery_r0, 2026-08-09):FAIL —— 翻正了但坐着 A soft joint-limit penalty charged the standing pose itself - the geometric-zero knee sat on its hard limit, so stand_v1 bent its knees to dodge 0.419 per step and leaned 4.1 deg forward; excluding the knee gave 0.24 deg
soft-limit-penalty-charges-nominal-poseBefore training, evaluate every penalty at the nominal pose; if a joint's soft limit sits inside the pose the task requires (a straight knee on its hard stop), exclude that joint from the soft-limit penalty and let the action clip enforce the hard limit.
Symptom
stand_v1 (retrained after the default pose moved to the CAD geometric zero and mirror augmentation was added) fixed left/right asymmetry (6.8 -> 0.0 deg) but settled at a 4.1 deg forward lean, where pure PD at the same default settled at 0.1 deg - the policy was actively pushing itself forward, which is exactly the real robot's failure direction.
Context
soft_joint_pos_limit_factor = 0.9 shrank the knee's soft limit to -/+0.1047 rad, while the geometric-zero default has the knee at q = 0, exactly on the hard limit. Standing in the nominal pose therefore paid 0.2094 x 2.0 = 0.419 per step in dof_pos_limits (alive earned only 0.5). The policy's way out was to bend the knees to -/+0.1013 rad, and the cost was the forward lean.
Change
stand_v1b: the knees excluded from dof_pos_limits (a straight knee IS the standing pose; the hard limit is still enforced by the action clip). No other change.
Outcome
stand_v1b: max tilt 0.3 deg, steady tilt 0.24 deg, asymmetry 0.1 deg, height 0.384 m - exactly nominal - with knees at -0.0007 / +0.0005 rad. It became the standing release used on the real robot, and later the standing side of the recovery switch. The same exclusion was carried into the recovery contract (knee at the clip in the standing pose) and the one-leg reward table.
Mechanism
A limit penalty whose soft boundary lies inside the nominal pose turns the nominal into a taxed state, and the policy buys its way out with whatever posture change is cheapest - here a knee bend paid for with lean.
Applies when
- a standing or default pose has a joint at or near its hard limit
- a policy settles in a small steady tilt that pure PD does not show
- soft-limit factors shrink limits uniformly across joints
“`soft_joint_pos_limit_factor=0.9` 把膝软限位内缩到 ∓0.1047,而几何零位 default **膝盖 q=0 正好压在硬限位上** ⇒ 站在标称姿态每步白扣 `0.2094 × 2.0 = 0.419` (alive 才 +0.5)。策略只能屈膝到 ∓0.1013 躲罚,代价是躯干前倾 —— 恰好是真机的 失效方向。 … 修掉"软限位罚标称姿态"后重训(`dof_pos_limits` 排除膝盖)。**前倾问题彻底消失** … 不再屈膝躲惩罚,高度正好落回标称 0.3840。”
train/README.md § 三期: 镜像对称增强 + 站立 v1 (2026-07-28) / stand_v1b (2026-07-28): 站立定版 With no term on foot attitude the robot stood on the edges of its feet (ankle roll -26 deg) from R0.5 to V2.5b; pricing it fixed that and turned stance width into the next free variable - the user saw both on video before any metric flagged them
unpriced-foot-attitude-is-a-free-variableList every posture quantity the hardware cares about (foot attitude, stance width, yaw, knee flexion) and make sure each is priced by a term with real gradient at the observed error; pricing one exposes the next, so re-inspect the feet-level video after every change.
Symptom
Watching the v2_5 video the user said the ankle roll after standing looked very strange - the feet were not flat. The feet view showed the right foot standing on its outer edge; median ankle roll at t = 8 s was -/+26 deg (limit +/-35), mirrored. This was the physical form of the ankle_roll saturation criterion that had failed since R0.5.
Context
No term priced foot attitude: feet_contact_upright counts an edge contact as contact, and stand_pose's wide exp kernel (sigma^2 = 9) gives almost no gradient at 0.45 rad. HoST carries an "ankle parallel" term (+20); this table never had one. Edge standing was made a blocking precondition for hardware (continuous ankle load, unstable contact, wear).
Change
V2.6 (single variable): flat_feet = (|q_l_ankle_roll| + |q_r_ankle_roll|) x upright gate x height gate, a linear hinge with a 5 deg margin, weight -2, continued from V2.5b.
Outcome
Ankle roll -/+26 -> 5.3/5.2 deg, ankle_roll saturation 6.6% (< 10%), feet flat on the feet-view video; success 99.6%, re-falls 0-1%. Then the user watched v2_6: hip yaw constantly tense and the legs very close together. The numbers: hip roll -/+4.9/4.8 deg against a nominal 25 - feet flat and hips open 25 deg cannot coexist without ankle compensation, the new term taxed that compensation, and nothing priced stance width. "Foot attitude as a free variable" was fixed and "stance width became the new free variable" - which the real robot then exposed as splits.
Mechanism
An optimizer spends every posture degree of freedom no term prices; closing one reallocates the slack to the next unpriced one.
Applies when
- a standing or landing posture looks wrong on video while gates pass
- a saturation criterion keeps failing on one joint
- a new posture term was just added
“用户看 v2_5 视频:"起身之后 ankle_roll 非常奇怪,脚根本不是平着站立"。 … 机理:奖励表**无任何脚掌姿态项** —— feet_contact_upright 边缘接触也算触地, stand_pose 的 exp 核(σ²=9)对 26°=0.45 rad 梯度≈0。脚掌姿态是自由变量。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §41 预注册 V2.6:flat_feet —— ⑥ 老账的物理形态被用户目视锁定