Training Coach
Doctrine
A report may cite any of these as doctrine-N.
doctrine-1Contract freeze and fingerprint disciplineThe policy I/O contract (observation layout, scales, history semantics, action pipeline) is frozen and fingerprinted; every exported policy is stamped and verified; contract changes ship as new versioned profiles that leave old artifacts bit-identical, and old policies run forever under their era's pinned profile.
Case. The 215-dim omni contract was frozen with a three-machine digest; the one contract-level extension (lateral feed-forward) went in as a new `omni_ff` profile with the old profile provably untouched, and the contract checker caught two real wiring bugs before any training (`contract-freeze-and-checker`). A silently changed gait-clock default would have fed old policies a 25% slower clock - closed by pinned legacy profiles (`legacy-profile-pinning`). A stale derived USD forked plant mass 2.2% until an automated source-vs-derived instrument gated it (`derived-asset-staleness-check`). A gain profile is part of the closed loop a policy was trained in and belongs in its stamp; the recovery line's anchored authority was left out of its manifest and recorded as the gap not to repeat (`gain-profile-belongs-in-the-stamp`), and a second policy behind a deploy-side switch made the handoff state itself a contract (`recovery-two-policies-and-a-state-machine`, `walk-recovery-fsm-handoff`).
Coach application. On any proposal touching obs/action semantics, defaults, or derived assets: demand the version/profile plan, the fingerprint update, and the checker extension in the same change; flag any old artifact that would run under new defaults.
doctrine-2Attribution by resolved training params - never eval-override knobsCapability differences between lineages are explained only by digging each lineage's *resolved* training configuration and eliminating columns; evaluation-side override knobs (kd-scale, power-scale, cycle-time) act on the plant for *every* policy and may serve as deployment mitigations but never as explanations.
Case. Low-friction robustness across 8 lineages x 3840 cells was traced to kd DR *bandwidth* - every lineage had ground friction pinned to (1.0,1.0), so "trained friction" could not be the axis; the parameter axis and the plant axis were explicitly separated after the first attribution conflated them (`kd-bandwidth-mu-law-attribution`). "Weak turning" on hardware was a power-scale plant effect, not a training gap (`deploy-knob-attribution-before-retraining`); slowing the deploy clock was out-of-distribution, not a feature (`cycle-time-override-is-ood`). The ground truth for what a run trained under is the logged per-run config, not the source tree (`resolved-config-is-source-of-truth`).
Coach application. Whenever asked "why is lineage A better", require the resolved-param table first; kill zero-variance columns; refuse explanations phrased in eval-knob terms; when a knob helps, label it deployment mitigation.
doctrine-3PASS gates become constraints; FAIL gates become objectivesOnce a skill passes its gate, that gate converts into a standing regression constraint (budget <= 2/20 against the parent baseline) for all later training; gates currently failing are the only legitimate objectives of the next rung.
Case. The C ladder ran one frozen 13-cell x 20-seed matrix at every rung with promotion = "new skill PASS and old skills within regression budget"; C1 was stopped and re-rooted precisely because it trained away the root's backward PASS (`fixed-acceptance-matrix-per-rung`, `preregistered-stop-criteria-per-rung`). The C4 product shipped only at 260/260 cells with zero regression.
Coach application. Keep the ledger: every PASS adds a constraint row; propose rungs only against FAIL rows; treat any constraint violation as stop-and-attribute, never "the next rung might win it back".
doctrine-4One variable per ladder rung - counted against what the checkpoint sawA rung changes one variable, where "one" is counted against the checkpoint's actual training state, not against the current config's diff; batching is allowed only when each change owns a disjoint symptom space with a pre-registered ablation order.
Case. Two rungs failed identically because resuming s1e-500 under the evolved config silently added four plant variables the checkpoint had never seen ("单变量纪律不只看「我改了什么」,还要看「checkpoint 见过什么」" - `resume-state-dr-audit`). v8 legally batched four orthogonal fixes with a written ablation order (`orthogonal-batch-with-ablation-order`); v9 spent one run completing a 2x2 factorial so either outcome convicted a factor (`fill-the-missing-factorial-cell`); v10b's three-way ablation wrongfully convicted the clock and had to be retried fairly.
Coach application. Before any resume: diff cfg against the checkpoint's logged training state. Before any batch: require the symptom-ownership map and ablation order in writing.
doctrine-5Pre-register risks, readings, and stop criteria before the ladderBefore a ladder or risky rung, write down the known risks, the interpretation of every plausible outcome, and hit-any-one stop criteria - frozen before training, tightened when priors say results should come fast.
Case. The C ladder opened with three numbered risks including the exact falsification condition for its own root choice; A/B arms carried "预注册读法(事后不改)" tables; a level expected to fail was run anyway for its pre-registered diagnostic value (`preregister-risks-and-fork-readings`). Stop criteria caught C4-redo rungs at +200 instead of full caps (`preregistered-stop-criteria-per-rung`); hardware sessions pre-registered per-config expected signatures and the disagreement rule "不改结论改账" (`preregistered-real-expectations`, `feasibility-accounts-lock-design-point`).
Coach application. Refuse to open a rung without the written risk/reading/ stop block; after results, read conclusions off the pre-registered table and flag any post-hoc reinterpretation.
doctrine-6Plant parameters are measured, never inventedEvery plant number carries measurement provenance: armature = N^2 x rotor inertia from no-load tests, friction split by rig and by API column, torque limits shaped by per-joint gait peaks, latency traced through the real pipeline, masses weighed - and DR bands are additive around the measured nominal, sized to the measured dispersion.
Case. Guessed friction was 2.5x low and guessed damping 5x high (`friction-measured-not-guessed`); armature had been 0 with a 9:1 gearbox (81x reflected inertia, `armature-n2-rotor-inertia`); a uniform torque derating was "the wrong shape" vs measured peaks (`torque-limit-shape-by-measured-peaks`); the delay implementation itself was a wrong plant for a whole lineage (`latency-lerp-reverse-extrapolation`); the run design point was locked by three accounts including the tau_limit/kd speed ceiling (`feasibility-accounts-lock-design-point`); identified friction had to land in the right simulator API columns to act at all (`sim-api-friction-columns`). The recovery and one-leg lines opened with the same kind of accounts before any reward existed - a connected static path and the torque along it for an armless get-up, and the gains single support needs to be holdable at all (`get-up-feasibility-accounts-before-training`, `single-support-gain-authority-probe`).
Coach application. For any plant value in a config review, ask "measured how?"; reject absolute ranges with no nominal; check API column mapping and derived-asset regeneration whenever measured values land.
doctrine-7Sim2sim gate before sim2real - under deployment conditionsEvery checkpoint passes a second, independently built simulator before hardware, and both the gate and the smoke loop run under the measured deployment conditions (real pipeline delay, honest contact parameters, the deployment gain/power profile).
Case. The standing order "先sim2sim 再sim2real" (`sim2sim-gate-before-sim2real`); acceptance flipped to match hardware only under measured condim/torsional friction (`eval-plant-honesty-contact-params`); gates moved permanently to `--delay 2` after the kicking incident (`pipeline-latency-is-plant-not-dr`); and the harness itself must be audited - a frame-convention bug in the cross-sim evaluator invalidated a whole line of verdicts (`body-frame-velocity-api-audit`). The recovery line's second simulator caught a torque penalty paid for by bracing the legs together (`torque-penalty-bought-by-leg-bracing`), and a 1.8x torque disagreement between the two plants stayed binding because its one surviving explanation was never tested (`torque-disagreement-between-simulators-unresolved`).
Coach application. Block any hardware request lacking a second-sim PASS at deployment conditions; when sim2sim and training-side metrics disagree, treat the evaluator as a suspect too.
doctrine-8Observation honesty - the actor's inputs are a hardware contractThe actor observes only signals the real robot produces with realistic noise; privileged truths go to the critic; history windows are estimators and must train under plant variation; rewards on quantities the actor cannot observe buy only average suppression, never closed-loop correction.
Case. Ground-truth velocity/forces went critic-only (`observation-honesty-critic-only`); frame_hist under zero DR memorized the trainer's plant fingerprint - 0/20 transfer (`history-obs-needs-plant-variation`); world-frame yaw rewards could not teach pull-back because heading is unobservable to the actor - correction was routed to the deploy outer loop instead of breaking the contract (`reward-observability-limit`, `deploy-heading-loop-and-align-training`).
Coach application. Audit every actor-obs element for hardware existence; require minimal plant jitter whenever history/recurrence exists; for each reward, ask "can the actor see this error?" and route correction tasks to outer loops.
doctrine-9Reward economics are audited in realized currencyReward design decisions are made on realized per-step magnitudes under the actual policy and command distribution: price the do-nothing optimum before adding a mode, compare achieved values to the computed ignore-floor, calibrate thresholds between measured healthy and sick distributions, and ship every new penalty with a withdrawal clause.
Case. feet_air_time at weight 2.0 realized 0.038 vs tracking 1.2 - drag was rational (`realized-contribution-audit`); ignoring a vy command cost 28-180x less than ignoring vx until a gated tracking term was added (`reward-cost-of-ignoring-audit`, `gate-new-reward-terms-by-command`); achieved-vs-floor separated "never learned" from "priced out" (`ignore-floor-diagnosis`); the foot-distance wall was placed between measured healthy (0.6% tax) and sick (55%) policies (`calibrate-threshold-between-healthy-and-sick`); the landing penalty carried a pre-registered stand-down condition and actually stood down (`calibration-threshold-with-withdrawal-clause`); two clearance terms were inert until zero-points and gate occupancy were checked (`inert-reward-term-audit`). A get-up policy sat because three gated terms paid the seated pose 84% of the return and the one term that could tell sitting from standing was an exp kernel reading 4.6e-5 at the real error (`seated-basin-dead-exp-kernel`); a torque-tail term was weighted by its measured steady value beside a peer term after the estimate proved 12x off (`tail-torque-needs-hinge-on-computed-demand`).
Coach application. Never discuss weights in the abstract: demand the realized-contribution table, the ignore-floor number, and the healthy-pay calibration before any reward edit is approved.
doctrine-10The zero-cost option must be the desired behaviorFor every penalty, name what the zero-cost option is; penalize failure events (slip, saturation excess, contact in flight windows), never the motion or joints that healthy behavior uses; make degenerate strategies fatal via termination where penalties cannot price them out.
Case. Joint-usage penalties for drift taxed a 1.4%-of-momentum channel 2.7/step and collapsed training; the slip penalty costs a non-slipping gait exactly zero (`penalize-the-slip-not-the-joint`). A frozen-at-clamp joint pays zero action-rate forever - only a pre-clip saturation penalty flips the cheat economics (`saturation-cheating-zero-rate-cost`). Ungated phase shaping made standing 42x more expensive than stepping and cooked the hip motors (`moving-gate-42x-stand-tax`); crouch-shuffling lived until a height termination deleted it (`termination-closes-degenerate-basin`). A gated penalty is an exit: the policy parked just outside an uprightness gate, then just under a height gate, to stop paying a stance tax, and only a positive band plus an always-on guard closed both (`penalty-gate-is-an-escape-hatch`); a soft-limit penalty that charged the standing pose itself bought a 4.1 deg lean (`soft-limit-penalty-charges-nominal-pose`); an unpriced foot attitude was spent on edge-standing (`unpriced-foot-attitude-is-a-free-variable`); and the one-leg line listed its cheapest cheats before training and still met one through a zero-gradient band (`enumerate-cheapest-cheats-before-training`, `binary-band-reward-fake-touchdown`).
Coach application. Run the "零代价的选项是什么" audit on every proposed term; convert motion taxes into event-conditional penalties; check the termination set against each known degenerate strategy.
doctrine-11Measurement discipline: independent referees, signs, distributionsA disputed measurement is adjudicated only by an independent algorithm from raw state; directional ability requires sign-antisymmetry under command reversal; bimodal metrics are reported as mode shares (never medians, never 3 seeds); ratios are not comparable when totals change; reward values compare only within one command distribution; single chaotic events never cross machines.
Case. The triple reversal - a good metric was "refuted" by a sibling metric that shared the disease (`independent-referee-for-metric-disputes`, `body-frame-velocity-api-audit`); same-signed +/- responses were bias, not turning (`same-sign-response-is-yaw-bias`); the swing median sat in a bimodal gap (`median-hides-bimodal-distribution`); "v6 is jitterier" died on absolute energies (`ratio-metrics-need-absolute-check`); yaw gain measured 15x wrong in an oscillating frame (`heading-integral-not-body-rate`); a 44% improvement evaporated under same-distribution comparison (`same-distribution-reward-comparison`); drift direction was a limit cycle (`multiseed-sign-test-for-drift`); a cross-machine push cliff was chaos (`single-impulse-recovery-is-chaotic`).
Coach application. Before accepting any surprising number: ask for the independent recomputation, the sign pair, the distribution shape, and the comparison conditions. Retract in writing when a metric falls.
doctrine-12The deployment pipeline is plantIrreducible pipeline properties - action latency, rate limits, power/torque scaling, teleop command mappings - are part of the nominal plant, modeled from day one and reproduced in every gate; deploy-side scalings are crutches that flag unmodeled plant, and they cannot be algebraically folded into training constants.
Case. Right-leg kicking was over-trained-delay x loop gain; power 0.8 was a gain-reduction crutch that retired when the delay was modeled (`pipeline-latency-is-plant-not-dr`); power derating damages non-forward axes first (`power-scale-hurts-nonforward-axes`); training at 0.4 scale as the "twin" of deploying 0.5 x 0.8 collapsed 0/20 (`deploy-scaling-not-training-equivalent`); one shared teleop speed sent an out-of-band lateral command and the robot clipped its own foot (`teleop-command-band-per-axis`); the latency DR range had not even covered the measured pipeline (`latency-dr-covers-measured-pipeline`). A rate limiter added at deployment only clipped a policy that kept commanding (`deploy-rate-limiter-windup`); moved into training and anchored on the last command it became an integrator in the balance loop (`slew-anchor-is-an-integrator`); anchored on the measured angle it bounded torque and kept the bandwidth (`beta-anchored-action-target`). The walking lines' safe setting, power-scale 0.8, cut the ends of the recovery policy's full-range travel and left its spikes alone; a gain inside the trained band did the job (`power-derating-cuts-full-range-contract`).
Coach application. Demand the measured pipeline latency/limits in the plant model and in gate conditions; treat every deploy-side derating as a question ("what is this compensating?"); block per-axis command sources that exceed training bands.
doctrine-13DR budget is finite; its distribution is the measured supportRobustness is a conserved budget: disturbance training on an already-hardened lineage borrows from existing margins; DR ranges span the measured deployment support - no fictitious tails (they buy degenerate gaits), no single constants (they allow thin-margin specialization); harden the plant only after the task distribution is final.
Case. The same push dose helped a narrow lineage and damaged a balanced one - budget conservation (`push-dr-conditional-budget-conservation`); wide latency tails bought drag-glide, constant values shipped 60% thinner tilt margins - the answer is a narrow band on the measured support (`dr-tail-plant-continuation`, `constant-value-dr-overfits-margin`); task-first ordering because hardening a soon-to-change task wastes budget (`task-shaping-before-plant-hardening`); COM randomization used deliberately as a behavior-shaping tool, and rolled back on symptom per its own contract (`com-randomization-forces-leg-spread`, `com-dr-rollback-on-symptom`). DR that is switched on can still be thin: the run policy fell in the frontal plane its gain-and-latency randomization never touched (`thin-dr-judged-by-channel-coverage`), and a friction priority settled under one action contract had to be re-measured under the next (`friction-priority-re-measured-after-plant-change`).
Coach application. Before any DR rung: check the untrained policy against the spec, the lineage's current DR load, and the measured real-world range; after it: audit retained margins, not just the new tolerance.
doctrine-14Gates measure what hardware feels: posture, margins, stripped assistsAcceptance batteries carry posture-class rows (tilt max median, per-joint L/R asymmetry, temperature) beside task rows, graded margin columns beside binary gates, chirality scored per side, at least one condition that removes the environment's free stabilization, and validated predictive scalars promoted into the gate.
Case. Three same-shaped judging errors - survival, displacement, wz-difference - all missed what the operator felt; posture metrics had the predictive power (`task-metrics-vs-posture-metrics`, `stand-gate-posture-not-survival`); binary survival saturated and hid a 60% margin gap (`constant-value-dr-overfits-margin`); v5 passed everything on the ground and failed suspended (`suspension-probe-removes-free-stabilizer`); the hip_roll (l+r) scalar predicted real drift direction and ordering and entered the battery (`hip-roll-sum-predicts-lateral-drift`); averages hide chirality (`chirality-scored-separately`); gait-quality gates are judged at speeds that demand a gait (`low-speed-commands-reward-dragging`). The recovery line added the rest of the kit: where failed episodes end, not only where they started (`end-state-confusion-matrix`); a frozen acceptance distribution with a pinned seed (`frozen-acceptance-distribution-and-pinned-seed`); video of the metric rollout itself (`video-as-acceptance-record`); and the admission that a 10 s episode cannot see a stance that fails after a minute (`episode-length-bounds-what-a-gate-sees`). The one-leg line removed a foot-spacing wall that no gate measured, and the feet met on hardware (`removed-wall-returns-on-hardware`).
Coach application. Review every battery for posture rows, margin columns, per-side scoring, and an assist-stripped condition; when operator feel and gates disagree, suspect the metric class first.
doctrine-15Fork and root selection: recoverability, maturity, frozen rewardsChoose fork roots by which candidate's deficits the coming training can pay back (precision is recoverable; lost plasticity, symmetry, and margins are not); prefer mature checkpoints as roots even when younger ones score better as products; never fine-tune through a reward change - continuation is legal only with the reward frozen and plant/DR widening one rung at a time.
Case. s1e-500 beat higher-precision candidates because its exclusive strengths were unrecoverable (`fork-root-recoverable-shortfall`); the b300 arm proved maturity is capital against adaptation shock (`root-maturity-vs-product-quality`); the B-arm scatter/half-recover/collapse signature falsified reward-change fine-tuning and drew the legal boundary for S2 continuation (`fine-tune-reward-change-falsified`).
Coach application. For root debates, build the exclusive-strengths table and ask "which side can be trained back?"; require dual-arm evidence for maturity claims; classify any proposed continuation as reward-frozen or not before approving.
doctrine-16Curricula: verified engagement, lineage counters, disease-phase gatingAutomatic curricula must prove they engage (a saturated ratchet is constant DR wearing a curriculum's name); every ramp counts lineage-cumulative progress, not per-process steps; penalties aimed at late-stage pathologies ramp in after exploration noise decays; difficulty rises on measured per-stratum success, never on schedule.
Case. The s1f ratchet capped at iter 248 and never engaged (`auto-curriculum-engagement-check`); the saturation ramp re-fired at +600 after every resume and no shipped product ever saw the penalty (`curriculum-counter-lineage-steps`); the same penalty worked once gated to the disease phase and became an untouchable mechanism (`gate-penalties-to-the-disease-phase`); record-high aggregate reward hid a fully-failing delay stratum (`aggregate-metrics-mask-subgroup-failure`); bucket share is not a gradient lever (`bucket-share-is-not-a-gradient-lever`). An assist curriculum keyed to a pooled success share was withdrawn on the strength of the categories that already worked (`curriculum-criterion-conditioned-on-lagging-category`); a pace set by per-step income moved only when that income was time-gated (`per-step-income-drives-speed-time-gate`), and the same gate had to be retired in a lineage without the disease (`time-gate-vs-wide-stance-retire-the-fix`).
Coach application. Ask every curriculum three questions: does it engage (show the internal state)? what does it count (process or lineage)? when is it present (against the pathology's phase)? Check where shipped checkpoints sit relative to every ramp.
doctrine-17Probe before training: feasibility first, hypotheses in tablesAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop, enumerate hypotheses in a written table audited against actual configs cheapest-first, race one probe per side of the sim2real boundary for hardware-only pathologies, and use suspended tests to acquit or convict actuators before blaming authority.
Case. "在黑暗里试钥匙" - four sidewalk rungs failed until an open-loop probe separated exploration/waveform/authority in one experiment (`open-loop-probe-before-reward-tuning`); the foot-drag mystery fell to a seven-hypothesis config audit (`hypothesis-table-code-audit`); the period-doubling was resolved by racing a reward-side and a plant-side evidence line - and both paid off, one per sub-case (`period-doubling-evidence-race`); the suspended test acquitted the roll actuator in one measurement (`suspended-test-isolates-actuator-authority`). A read-only configuration probe told a wall from a slope in the recovery line's seated basin (`configuration-probe-wall-not-slope`), and the fix it pointed to - where the feet are - took prone from 0/159 to 158/159 (`prone-dead-end-is-foot-placement`); a knob that did not move its variable was recorded as no test of the idea (`dof-vel-penalty-is-not-a-pacing-knob`).
Coach application. When a skill resists training, prescribe the probe before any further reward edits; require verified target trajectories before imitation terms; keep a falsified-fixes list so closed roads stay closed (`amplitude-cut-falsified-yaw-fix`).
doctrine-18External advice is recomputed locally; values transfer as ratiosEvery external suggestion is classified adopt / already-have / modify / trap by recomputing its claim on the local reward table and probe data; numeric values transfer only as dimensionless ratios (to tracking weight, leg length, sqrt(gL), control rate); citations are verified to exist.
Case. "Start vy very small" would have destroyed sidewalk learning on this reward table - the gradient scales quadratically (`external-advice-audit-against-own-arithmetic`); swing-height targets and weights transferred correctly only through leg-length and tracking-ratio scaling (`transfer-ratios-not-absolutes`); the "6-step delay" was refused for lacking a control rate (`latency-dr-covers-measured-pipeline`); a borrowed reference's structure was FK-verified and its amplitude re-derived from the division of labor (`reference-structure-fk-amplitude-division`); retrieval agents fabricated verbatim arXiv quotes - only source-verifiable material was used; and one dismissed suggestion later proved right for a different mechanism, and was credited (`cycle-average-tracking-for-gait-quantities`). An advisor's staged state machine turned out to exist in none of the three papers it cited, and reading them changed the plan (`advisor-paraphrase-vs-paper`).
Coach application. Intercept every "paper X does Y" with the local recomputation; convert absolutes to ratios before comparison; verify quotes; revisit dismissed advice when new mechanisms appear.
doctrine-19Hardware sessions are scripted experiments, not tuning sessionsReal-robot time executes a pre-registered matrix: risk-ordered (baseline first, fragile last with a spotter), stage-gated (suspended smoke before ground), A/B sessions bracketed by a repeated reference run, operators briefed on measured zero-command and untrained-axis behavior, chirality-aware disturbance protocols, no field tuning - the only legal field changes are scripted, single-variable, and self-reversing.
Case. The S2 acceptance sheet (`risk-ordered-real-deployment`, `battery-bracketed-real-ab`, `know-zero-command-behavior`, `push-test-chirality-protocol`, `no-field-tuning-protocol`); the RAM-only torque experiment with automatic power-cycle rollback (`reversible-single-variable-field-experiments`); and the sim-veto rule - even sim's condemnations get one safeguarded hardware check when they judge the purpose-built configuration (`sim-veto-needs-real-confirmation`). The recovery line's first real run went ahead with its preconditions unmet and was stopped as dangerous (`first-real-get-up-violent-stage-one-policy`); after it: a staged hang, mat and floor protocol (`staged-hang-mat-floor-for-get-up`), a fixed power-cycle pre-flight and two-machine discipline (`power-cycle-preflight`, `two-machine-config-discipline`), a fall guard replaced rather than switched off (`fall-guard-becomes-a-state`), and logs that are part of the run (`hardware-log-is-the-attribution-input`).
Coach application. Turn every hardware request into a runbook with order, gates, brackets, briefing, and anomaly plays; refuse improvised parameter changes on the floor.
doctrine-20Close questions in writing; restart when the debt is structuralAudited questions get frozen verdicts with citable wording and an explicit reopening bar; hardware verdicts are dated by deployment-stack and calibration state and expire when those change; and when successive rungs shuffle symptoms without net progress, freeze the lineage as regression baselines, pay the structural debts, and retrain minimal - carrying laws and instruments, not weights.
Case. The chirality and COM questions were closed with frozen wording and "no reopening without new hard evidence" (`frozen-verdicts-semantic-boundaries`); v5/v6's condemnations expired with the deploy stack (`stale-verdicts-under-old-stack`); a 2-degree calibration fix moved the whole runnable envelope (`zero-offset-calibration-shifts-envelope`); plant upgrades are era boundaries with paired re-baselining (`plant-swap-invariants-vs-shifts`); and the 2026-08-05 reset froze v5-v11, fixed the latency FIFO / manifest / sampling / reward-table debts, and restarted - producing the lineage that reached hardware SOTA (`freeze-lineage-fix-structure-restart`, `minimal-reward-table-with-provenance`). The recovery line's real-robot verdicts ended up in three places that disagree, one of them an undated note in a command file (`write-hardware-verdicts-back`).
Coach application. Maintain the closed-questions ledger and quote it when symptoms recur; stamp verdicts with stack/calibration versions; when a team is three rungs into symptom-shuffling, raise the restart question explicitly with the freeze-fix-restart pattern.
doctrine-21Name the quantity in the space it lives inA goal, reward term or acceptance criterion about the feet, the base or the contact state is computed from the quantity itself - world poses, forces, per-category outcomes - never through a joint-angle, single-signal or pooled stand-in that assumes everything else sits at nominal; and every detector is validated on a behaviour known not to contain the event before it becomes a gate.
Case. The recovery line was caught three times: |ankle roll| as "flat feet" sold stance width and the real robot slid into the splits, a hip-roll criterion was confounded by 50 deg of yaw, and the joint table said 0.271 m where the feet were 0.159 m apart; task-space terms produced the first flat, wide stance (`joint-space-proxy-for-task-space-quantity`). Flight detection lied in both directions across two lines - foot height flagged 40% false flight on a walking gait, contact force alone flagged slip chatter as hops (`contact-detector-single-signal-lies`). A pooled height average described a robot that did not exist - six in ten standing, four in ten sitting (`zero-partial-credit-is-not-an-iteration-problem`) - and the walking line had learned the same lesson on yaw rate (`heading-integral-not-body-rate`).
Coach application. For every reward term and gate row, ask what physical quantity it stands for and whether it is measured directly; flag joint-space or single-signal stand-ins for task-space goals, ask for a detector validated on a negative control, and split pooled metrics by category before reading them.
doctrine-22Continuation needs a live gradient; a release is chosen by a scanContinue a converged policy only on a change that creates a live gradient, on a short budget, with every checkpoint scanned on the transfer axis; choose a release by running the full battery over a band of checkpoints and stop on signals, never by taking the last one; and when edits to the terminal phase cannot move a behaviour, roll back and retrain with the constraint present from the start, keeping the order in which the lineage acquired its mechanisms as explicit curriculum phases.
Case. A continuation with no new gradient drifted MuJoCo transfer from 100/98% to 80/28% while every Isaac gate stayed perfect, and a live-gradient continuation at the same depth kept it (`converged-continuation-is-poison`). One-leg checkpoints 100 iterations apart failed 1 and 38 of 40 cells, and late ones degraded (`checkpoint-choice-is-a-full-gate-scan`). Four in-lineage stance fixes failed because the stance was the end of the get-up path, and from scratch it grew right (`stance-decided-by-get-up-path`); fixes stacked on degraded states were rolled back by the user (`stop-stacking-roll-back-and-audit`); and the lineage's final recipe, trained from scratch in one run, sat at 0% because the order of its curriculum was part of the product (`curriculum-history-is-part-of-the-product`). The omni line's short adaptation budgets and mature roots are the same law seen from the other side (`continuation-budget-not-from-zero`, `root-maturity-vs-product-quality`).
Coach application. Before approving a continuation, ask for the new gradient, the budget and the transfer axis in the scan; before approving a release, ask for the scan; after three rungs without progress on the target, propose rolling back to the last good checkpoint and a from-scratch phase plan instead of a fourth patch.
Experience cards
144 cards matching “torque-penalty-bought-by-leg-bracing”.
A torque-tail penalty was paid for by bracing the legs against each other - the second simulator's leg-contact count caught it, and the first explanation ("the trainer can't see self-collision") was retracted from the run's own config
torque-penalty-bought-by-leg-bracingWhen a penalty lowers a demand metric, look for what the policy traded to get there - keep self-contact frames and foot spacing as standing sim2sim readouts - and check any "the trainer cannot see X" explanation against the run's resolved config before it enters the record.
Symptom
After R3.1's torque_headroom term collapsed the demand tail, MuJoCo success fell 100 -> 98% and leg-leg contact frames at mu 1.0 rose 750 -> 2,190 (worst rollout 177 -> 450). The one failure (prone seed 2) had the legs crossed, one foot on the other leg, trapped at 0.067 m - visible on video.
Context
Across the ten prone seeds, foot spacing and leg-leg contact frames were monotonically anti-correlated, and the failure was the extreme of the series. Pulling the legs toward the midline shortens the hip_roll lever arm and lowers torque demand. At the time the spec explained it as Isaac training without self-collisions ("a free lunch in a simulator without self-collision").
Change
Leg-leg contact frames and foot spacing were tracked in every MuJoCo gate; R3.2's candidates were "train with self-collision on" or "a minimum leg spacing term" - not stacked.
Outcome
The next rung's joint-velocity penalty incidentally erased the dependency (2,190 -> 86 frames). On 08-10 the runs' logged env.yaml showed enabled_self_collisions true in both r3_1 and v2_2 (inherited from walk v10): the tangle was physically learned bracing, visible to both simulators, and the Isaac/MuJoCo contact-count gap was mesh and contact fidelity. The "self-collision debt" narrative was withdrawn for the whole line.
Mechanism
A penalty on demand rewards any configuration that lowers demand; legs pressed together act as a mutual support that fails when contact geometry shifts slightly.
Conflicts
§24 attributes the dependency to self-collisions being disabled in training; §36 retracts that from the runs' env.yaml ("§24's mechanism explanation was wrong") and keeps the older sections unedited as history.
Applies when
- a torque, impact or energy penalty improves its metric and cross-sim success drops
- legs or links approach each other after a regularization change
- an explanation relies on a simulator setting nobody checked in the run config
“prone 十个 seed 逐条看,脚距与腿-腿接触帧数单调反相关, 而唯一失败的那条正是最极端的一条 … 机制上说得通:把腿收到身体中线附近能缩短 `hip_roll` 力臂、降低力矩需求”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §24 代价:MuJoCo 成功率 100% → 98%,病因是两腿卡住 A stronger action_rate penalty cut the median torque demand under the gate and left the p99 at 4x the limit - only a hinge on the pre-clip (computed) torque, weighted by comparison with a peer term, collapsed the tail
tail-torque-needs-hinge-on-computed-demandJudge actuator demand against the deployed limit, read the pre-clip demand (applied torque is censored and gives no gradient on the excess), use an L2 rate penalty for the median and a thresholded hinge on computed demand for the tail, and set a new term's weight from its measured steady magnitude next to a peer term rather than from a back-of-envelope estimate.
Symptom
After R0.5 hip_pitch delivered torque sat at its 12 N*m limit in a typical get-up (demand 119-125% of the limit, p99 4.2x) - zero control margin at exactly the moment modelling error matters.
Context
The 12/17/11 N*m limits are deployment limits written into robot.yaml by set_torque (RS06 at 33% of rated), and simulation uses the same effort_limit - so the gate is judged against them, not the 36 N*m rating (an early reading against the rating was retracted). Applied torque is clipped at the limit - censored data - so demand must be read from computed_torque. With the full-range action contract (hip_pitch scale 1.309, kp 30) a single-step action change of 0.306 already saturates hip_pitch, and action_rate penalizes exactly that change.
Change
R3.0: action_rate_l2 -0.01 -> -0.03 (child-run). R3.1: new torque_headroom = sum relu(|tau_computed|/limit - 0.9)^2, normalized so three motor types share a scale. Its weight was first estimated at -0.1, measured in a 12-iteration run at an effective -0.019 (12x smaller - the estimate had mixed a per-episode-peak p99 with a per-step p99, and at 1% of upright it would have been numerically absent), and set to -0.5 so its steady value (-0.095) matched action_rate's (-0.097).
Outcome
R3.0: sum |da|^2 -64%, success 99.6 -> 100%, delivered median = demand median (the clamp no longer fired in a typical episode), gate PASS at worst 79.9% - but p99 unchanged (hip_pitch 419-432% -> 427-436%). R3.1: p99 hip_pitch -> 148-189% (-57 to -65%), knee 422-439% -> 233-234%, saturation duty -60%, success 100%; the worst joint became hip_roll at 67.7%. Its cost appears in torque-penalty-bought-by-leg-bracing.
Mechanism
A squared-rate penalty presses the whole-episode sum and moves the typical step, not rare spikes; the spikes came from the kp term (large targets while a limb is blocked by the ground - velocity alone could not reach them under vel_limit), and a penalty on applied torque cannot see demand above the clip because every excess sample reads as exactly the limit.
Applies when
- torque demand saturates actuator limits in high-effort skills
- a smoothness penalty improves medians but not peaks
- a new reward term's weight is set by estimate alone
“**必须用 `computed_torque` 而不是 `applied_torque`**:后者被 `effort_limit` 削平, 是删失数据,超限样本全被压成"恰好等于限",对超限部分梯度恒为 0。 … 改按同侪定标取 **−0.5**(稳态 ≈ −0.095,与 `action_rate_l2` 的 −0.097 等量)。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §24 R3.1(torque_headroom 力矩需求越限罚) A proposal in the runbook - torque and action limits as versioned safety tiers (classroom / research / expert) written to motor RAM and read back, separate from the reward's effort penalty - recorded as a proposal, its implementation unrecorded
safety-limits-are-a-layer-not-a-rewardKeep hardware limits as an explicit, versioned safety layer (tiers written and read back at start, the persisted default the safest one) and the effort penalty as a behaviour layer; when a skill needs more torque, change tier deliberately rather than trading one layer against the other.
Symptom
Running and jumping need more torque than the deployed limits allow, and the temptation is to trade the training-side effort penalty against the hardware limit, or to hand a new user a robot "tuned however the last person left it".
Context
A message pasted into the operator runbook (undated, citing Berkeley's practice of storing the full motor configuration as JSON with write and read-back scripts) proposes: configuration is a versioned artifact, not a verbal agreement; three safety tiers in robot.yaml beside the gain and policy profiles - classroom (RS06 limited to 10 N*m, lateral joints clamped: "however bad the policy, it only moves awkwardly"), research (14 N*m, clamps at twice the measured need, the default) and expert (the 36 N*m rating, joint limits only, requiring an explicit flag); deploy writes the tier to motor RAM at start and reads it back, while the stored copy stays classroom so a power cut returns to the safest state. It frames limits as the safety layer and the effort penalty as the behaviour layer - more torque for running means switching tier, not weakening the penalty.
Change
None recorded: the message ends by asking which to do first, a rollback or the tiers.
Outcome
The sources do not record the tiers being implemented; the deployed limits stayed at 12/17/11 N*m through the recovery and one-leg lines (the one-leg spec treats raising the RS06 limit as a separate, unapproved hardware decision). Related and recorded elsewhere: torque limits were written to RAM only in a scripted, self-reversing field experiment.
Mechanism
Hardware limits bound the damage any policy can do; reward terms shape what a policy prefers. Mixing them either weakens safety to buy behaviour or distorts behaviour to buy safety.
Applies when
- a new skill needs more torque than the deployed limits
- robots are handed to students or new users
- motor configuration lives in people's heads or in the firmware only
“配置是版本化的产物,不是口头约定。 … deploy_policy 启动时按档写进电机 RAM 并读回校验(落盘的那份永远保持 classroom,断电自动回到最安全状态)。 … 限幅是安全层,dof_torques_l2 是行为塑造层,它们在不同的层,不冲突。跑步要更大力矩就换档,而不是去动训练里的省力惩罚。”
RL系统/FOLLOW THIS copy 2.md § 面向 developer / 教育机构该怎么做 (pasted proposal, undated) Torque caps cannot soften footfalls - impact is falling-mass momentum, only the reward can treat it
landing-impact-not-fixed-by-torque-capsClassify each hardware symptom by the physics that sets it: quantities fixed by ballistic momentum at contact must be treated through the policy's trajectory (reward terms on approach velocity/force), never through actuator caps - and size such penalty weights against your own tracking reward, not a lighter robot's.
Symptom
Footfalls slammed at 1.78x body weight in sim baseline (human walking: 1.2-1.5x); the tempting hardware-side fix was cutting actuator torque limits.
Context
Measured directly: scaling torque limits from x1.0 down to x0.4 left peak landing force essentially unchanged (1.75 -> 1.78x body weight) - the impact force comes from the momentum of the falling mass at touchdown, not from motor effort. The fix has to change the trajectory, i.e. the policy, i.e. the reward: feet_contact_forces penalty above a threshold of 113 N (= 1.2x the 9.58 kg robot's weight), clipped, weight -0.005. The weight was sized locally, not copied: the reference robot's -0.001 would amount to 0.9% of tracking reward on this robot ("策略不会理它" - the policy would ignore it); -0.005 gives 4.4%.
Change
Added threshold-type contact-force penalty (-0.005, threshold 1.2x body weight) as one of v6-minimal's three changes; hardware torque cuts explicitly rejected as a footfall treatment.
Outcome
Landing force 1.72x -> 1.55x by v6 (target <1.5x, missed by 3% - progress booked honestly); the torque-cap dead end was documented so it would not be retried.
Mechanism
At touchdown the ground stops a ballistic mass; the impulse is set by approach velocity and effective inertia, which motors can no longer influence in the final instant. Only earlier trajectory choices (approach velocity, timing) reduce it - and those are selected by the reward, not by actuator limits.
Applies when
- footfall impact or landing noise on hardware
- proposals to derate torque as a softness fix
- importing contact-force penalty weights from another robot
“⚠️ 硬件限扭降不了落脚力 —— 砸地力来自下落质量的动量: 实测 tau ×1.0→×0.4, 落脚力 1.75→1.78× 体重纹丝不动。只有这条奖励能治。… ⚠️ 权重不能用 Pi 的 −0.001 —— 实测在我们身上只占跟踪奖励的 0.9%, 策略不会理它 (Pi 6.94 kg 更轻)。−0.005 给到 4.4%。”
train/WALK_V6_MINIMAL.md § ③ 新增 feet_contact_forces Every gate on a penalty is an exit - to stop paying a stance tax the policy parked 2 deg outside a 30 deg uprightness gate (lunging), and, from scratch, just under a height gate (crouching); a positive band and an always-on guard fixed both
penalty-gate-is-an-escape-hatchNever gate a penalty on a state the policy can leave by getting worse; use always-on guards for what must never happen and positive, gated bands for what you want, and count every gate on a penalty as one more escape route to check in the logs.
Symptom
V2.9 added stance_width_task = relu(0.34 m - foot spacing) x standing gates, weight -10. Three checkpoints scored 0% on acceptance: standing height reached, feet on the ground, angular rate low, but the torso leaned 32.5/32.3/31.9 deg in a fore-aft lunge. The training dashboard read "tax paid off, base_height at full value".
Context
The penalty was gated by uprightness (tilt < 30 deg) and standing height; its tax had no time gate (500 steps x -1.65) while the standing income sat behind a 3 s zero gate (~325 steps), so leaning just past 30 deg lost a little gated income and saved the whole tax. base_height has no upright gate, so the lunge still collected it. The first metric also measured full horizontal spacing, so a staggered lunge counted as "wide".
Change
Two laws written down: a penalty may only carry gates the policy cannot escape by getting worse (make it an always-on guard) or it becomes a positive band ("not earned" is not "escaped"); and width is measured laterally in the base yaw frame. From scratch (V3.1 P1) with the lateral metric but the same gates, the policy parked just under the height gate instead (base_height 1.176/1.5, h ~ 0.30 m against a 0.3264 gate), the beta curriculum never advanced in 1,700 iterations, and the run was stopped early. P1b flipped the penalty into a positive band +2.0 x clamp(lateral / 0.34) x standing gates; P1c added yaw_guard = -5 x relu(|hip_yaw| - 30 deg), always on, no gate, no exemption.
Outcome
P1b: lateral stance 0.364 m, all four categories 100%, MuJoCo mu 1.0/0.4 both 100%. P1c: all six acceptance criteria passed for the first time on the line (hip-yaw saturation 1.2%), the guard's tax converging to -0.016 (almost never touched).
Mechanism
A gated tax that is not paid is saved, so the policy moves to the cheapest state just outside the gate; a gated income that is not earned is simply lost, so a positive band has no exit. HoST's style penalties are ungated or binary - the same law seen from the other side.
Applies when
- adding a penalty multiplied by an uprightness, height, phase or contact gate
- a policy settles just beyond a gate threshold
- training metrics look paid-up while acceptance collapses
“**罚项的门 = 策略的逃生门**。带直立门的负项可以靠"变得更差"(倾出门外) 全时免税;HoST 的 style 罚全部无门控/二值恰是同一律的反面实证。修律: 负项只许挂"变差逃不掉"的门(上限护栏 always-on),或改正向 band (收不到 ≠ 逃掉)。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §46 定案(血统内第四败 + 两条新律) Set torque limits per joint from measured gait peaks - a uniform percentage is the wrong shape, and training must use the deployed numbers
torque-limit-shape-by-measured-peaksMeasure per-joint torque peaks in the actual gait and set each limit as measured-peak x margin capped at rating; then propagate the same numbers into training and add an automated deploy-time consistency check - never derate by a uniform percentage, never let training assume torque deployment will not grant.
Symptom
A uniform 50% torque derating (18/8.5/7) had piled safety margin on the joints that never use it while cutting the busiest joint below half its measured demand.
Context
Per-joint gait peaks were measured (walk_v5 at cmd 0.3/0.6): RS06 (hip_pitch/knee) uses 5.5-5.9 N*m = 15-16% of its 36 N*m rating - cutting it to 12 is a free safety win; RS02's ankle_pitch runs at 16.2 N*m = 95% of its 17 N*m rating - "它是速度的硬件瓶颈", no room to cut; RS00 measured 36-44%, capped at 11. The resulting shape 12/17/11 replaced the uniform percentage. Sweeps across several limit sets (rated / 50% / 14-17-11 / 12-17-11) produced identical speed, lift, and landing force - within this range the limits do not shape the gait; what matters is consistency: "关键是训练和硬件必须是同一个数", because the exporter fills effort_limit from tau_limit, and a policy trained at rated 36/17/14 "会假设有三倍力矩可用" while deployed at 12/17/11 (exactly the v5 cross-generation inconsistency later suspected in its wild kicking).
Change
robot.yaml tau_limit set to the measured-shape 12/17/11, firmware written to match, and train/isaac_values.py regenerated so training sees the same limits; the deploy tool self-checks limits against robot.yaml on every run.
Outcome
Free safety margin captured where demand is low, the real bottleneck joint left at rating, and the train/deploy torque worlds unified with an automated consistency check.
Mechanism
Torque demand is grossly unequal across joints in a gait (15% vs 95% of rating here); a uniform percentage misallocates the safety budget by construction. And since the trainer treats effort_limit as a plant truth, any train/deploy mismatch is an invisible plant gap of exactly the mismatch ratio.
Applies when
- choosing safety torque limits for a legged platform
- training-vs-deployment actuator limit audit
- one joint runs near rating while others idle
“曾用统一 50%(18/8.5/7)是错的形状: 把余量堆在用不到的 RS06 上, 却把 ankle_pitch 砍到需求的 52%。… RS02 在 0.6 m/s 已用到额定 95%, 它是速度的硬件瓶颈 … 实测多组限幅 … 完全一致 —— 限幅在这个范围对步态零影响, 关键是训练和硬件必须是同一个数。… 若训练仍按额定 36/17/14, 学出的策略会假设有三倍力矩可用。”
train/WALK_V6_MINIMAL.md § 3. 训练侧必须同步的一件事 A soft joint-limit penalty charged the standing pose itself - the geometric-zero knee sat on its hard limit, so stand_v1 bent its knees to dodge 0.419 per step and leaned 4.1 deg forward; excluding the knee gave 0.24 deg
soft-limit-penalty-charges-nominal-poseBefore training, evaluate every penalty at the nominal pose; if a joint's soft limit sits inside the pose the task requires (a straight knee on its hard stop), exclude that joint from the soft-limit penalty and let the action clip enforce the hard limit.
Symptom
stand_v1 (retrained after the default pose moved to the CAD geometric zero and mirror augmentation was added) fixed left/right asymmetry (6.8 -> 0.0 deg) but settled at a 4.1 deg forward lean, where pure PD at the same default settled at 0.1 deg - the policy was actively pushing itself forward, which is exactly the real robot's failure direction.
Context
soft_joint_pos_limit_factor = 0.9 shrank the knee's soft limit to -/+0.1047 rad, while the geometric-zero default has the knee at q = 0, exactly on the hard limit. Standing in the nominal pose therefore paid 0.2094 x 2.0 = 0.419 per step in dof_pos_limits (alive earned only 0.5). The policy's way out was to bend the knees to -/+0.1013 rad, and the cost was the forward lean.
Change
stand_v1b: the knees excluded from dof_pos_limits (a straight knee IS the standing pose; the hard limit is still enforced by the action clip). No other change.
Outcome
stand_v1b: max tilt 0.3 deg, steady tilt 0.24 deg, asymmetry 0.1 deg, height 0.384 m - exactly nominal - with knees at -0.0007 / +0.0005 rad. It became the standing release used on the real robot, and later the standing side of the recovery switch. The same exclusion was carried into the recovery contract (knee at the clip in the standing pose) and the one-leg reward table.
Mechanism
A limit penalty whose soft boundary lies inside the nominal pose turns the nominal into a taxed state, and the policy buys its way out with whatever posture change is cheapest - here a knee bend paid for with lean.
Applies when
- a standing or default pose has a joint at or near its hard limit
- a policy settles in a small steady tilt that pure PD does not show
- soft-limit factors shrink limits uniformly across joints
“`soft_joint_pos_limit_factor=0.9` 把膝软限位内缩到 ∓0.1047,而几何零位 default **膝盖 q=0 正好压在硬限位上** ⇒ 站在标称姿态每步白扣 `0.2094 × 2.0 = 0.419` (alive 才 +0.5)。策略只能屈膝到 ∓0.1013 躲罚,代价是躯干前倾 —— 恰好是真机的 失效方向。 … 修掉"软限位罚标称姿态"后重训(`dof_pos_limits` 排除膝盖)。**前倾问题彻底消失** … 不再屈膝躲惩罚,高度正好落回标称 0.3840。”
train/README.md § 三期: 镜像对称增强 + 站立 v1 (2026-07-28) / stand_v1b (2026-07-28): 站立定版 Calibrate a wall penalty by measuring healthy and sick policies - healthy pays ~0, the disease pays a wall
calibrate-threshold-between-healthy-and-sickCalibrate every threshold penalty by evaluating its exact formula on replays of at least one healthy and one sick policy: place the threshold between their distributions, size the weight so the sick policy pays a decisive fraction of tracking while the healthy one pays ~0, and pre-compute neighboring thresholds for cheap adjustment.
Symptom
Real walk_v7 occasionally clipped its own legs (stance narrowed to 133 mm mean vs nominal 214.5); a foot-distance penalty was needed, but an uncalibrated threshold/weight risked either doing nothing or becoming a reverse barrier.
Context
The term (relu(d_min - lateral foot distance), measured in the base yaw frame because world-frame y is meaningless after turning) was calibrated before training by replaying three known policies through the exact reward formula at the acceptance operating point: healthy v5 (183 mm) pays 0.6% of tracking - effectively free; narrowed v7 (133 mm) pays 22% - effective widening pressure; collapsed v8 (93 mm) pays 55% - a wall. d_min 0.16 was placed deliberately between healthy and sick, with alternative thresholds (0.14/0.18) pre-computed in the tool output for later adjustment. The shape self-check was named as a standing question: "先问'零代价的选项是什么'" - the zero-cost region must be exactly the desired behavior.
Change
feet_lateral_distance added at d_min 0.16 / weight -10, with telemetry expectation pre-registered (should decay toward 0 as stance learns >160 mm; if bow-legged over-widening >214 appears, only then discuss an upper bound).
Outcome
v9_probe on hardware: no leg contact ("没碰腿(N2 兑现)"), stance min 145/126 mm green; the term's zero-cost design left healthy gait untaxed.
Mechanism
A relu threshold penalty defines a free region and a priced region; its correctness is entirely in where the boundary sits relative to the healthy and pathological distributions. Replaying known-good and known-bad policies through the exact formula measures both distributions in the term's own currency, making the threshold and weight a placement decision instead of a guess.
Applies when
- adding any relu/threshold-style wall penalty
- a safety margin (foot distance, joint limit, clearance) needs enforcement without taxing normal behavior
- choosing between candidate thresholds for a new term
“形状自检 (v6 横向组/v8-B 的教训 —— 先问"零代价的选项是什么"): 标称站距付 0, 健康步态付 ~0, 收窄才付费 … v5(健康) 183 mm … 0.6% ≈ 免费 | v7(收窄) 133 mm … 22% —— 有效推宽 | v8(塌陷) 93 mm … 55% —— 墙 … d_min=0.16 恰在 v5(183)与 v7(133)之间”
train/WALK_V9_SPEC.md § 2. N2 —— 脚距惩罚(已完成权重预标定) Before training a one-leg stand the spec named the cheapest cheats - hopping on the support foot, a raised foot resting unloaded, a leg tripod - and gave each a countermeasure and a gate; one still appeared and was caught by exactly those gates
enumerate-cheapest-cheats-before-trainingBefore training, list the cheapest behaviours that would satisfy each reward term without doing the task, give each a countermeasure in the reward and a gate in acceptance, and prove the intended behaviour is reachable with a probe - then treat any gate the policy games as evidence about the reward, not the gate.
Symptom
The literature's single-leg benchmark reports eight state-of-the-art general policies holding a clean one-leg stand 0 times out of 90 - they survive by sneaking steps and hops - so the task's first adversary was the policy's own cheating.
Context
The spec's shape self-check ("what is the zero-cost option?") listed, for the one-foot bucket: the cheapest cheat, a foot resting on the ground without load, countered by a 5 N contact threshold plus positive swing income; the second cheapest, small hops on the support foot to reset balance, countered by a continuous support-air penalty plus a gate of zero support-foot flight segments. The probe that preceded training had already seen a third: early low-lift postures "survived" by pressing the swing foot at 78-95 N, a leg tripod, removed by folding the shank back. The two-foot bucket was checked too: its zero-cost behaviour is ordinary standing, with no odd base state.
Change
Countermeasures and gates written before training: swing-contact and support-air penalties, gate 2 (zero swing-foot contact frames above 5 N), gate 3 (zero support-foot flight segments).
Outcome
The first run still found the unloaded-foot cheat (a binary reward band gave it no gradient to lift) - and it was caught, by the contact gates and the cross-simulator comparison, not discovered on hardware. The retrained V0 passed all gates 40/40, including zero support-foot flight after the flight detector was corrected.
Mechanism
A policy optimizes the reward, not the intent; the cheapest behaviours that satisfy the reward are predictable from the reward's structure, and a gate written for each before training turns a silent cheat into a failed row.
Applies when
- designing rewards for balance, contact or "hold still" tasks
- benchmark policies are known to cheat the task
- writing acceptance gates for a new skill
“文献里 8 个 SOTA 通用策略在单脚站基准上 0/90 干净保持， 全靠偷步偷跳活命，这是本任务的第一反作弊对象 … 单脚桶下最便宜的作弊是"脚虚放地上不受力"——接触判定 >5 N 力阈（沿用），配 swing_height_band 正收入拉开。 … 第二便宜是"支撑脚小跳重置"——support_air_penalty 连续罚 + 验收门支撑脚腾空段=0 双保险。”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §0 目标口径 / §5 形状自检(零成本选项是什么) A joint-velocity penalty meant to slow the get-up cut joint speed 16% and left the get-up time unchanged - the knob never moved the variable, so the idea it was meant to test stayed untested
dof-vel-penalty-is-not-a-pacing-knobBefore reading a result as a test of an idea, check that the knob actually moved the independent variable; velocity regularizers smooth a schedule they do not set, and a schedule driven by per-step task income moves only when that income's time structure does.
Symptom
The get-up took 0.6-0.9 s in Isaac with large torque demand; the user proposed getting up more slowly so less torque would be needed.
Context
The idea had support in the accounts: the acceptance bound is an upper bound of 5 s (5-8x margin), the quasi-static squat path peaks at 25% of the limits, and rolling over needs no momentum. R3.2 raised dof_vel from -1e-3 to -5e-3 as the single variable.
Change
dof_vel -1e-3 -> -5e-3 (child-run from R3.1).
Outcome
Get-up medians moved +0.02-0.04 s (noise); raw joint velocity -16%; torque demand median got worse (hip_pitch 46-48% -> 63-67%) as the new term competed with torque_headroom on the same joints; MuJoCo 98 -> 96%. Verdict FAIL on the knob, not on the idea, and the rung was not adopted. When pace was later attacked through the income's time structure (V2.5/V2.5b), the MuJoCo get-up moved into the 3.5-4.5 s design band.
Mechanism
The pace was set by base_height_progress paying for every step spent high (stand earlier, earn more); a velocity regularizer only smooths motion along the same schedule and does not change when the robot stands up.
Applies when
- trying to make a skill slower or gentler with smoothness penalties
- an experiment's primary metric did not move and a verdict is being written
- two penalties act on the same joints
“**关键判读:`dof_vel` 罚只把关节速度压了 16%,而起身用时一点没变。** 也就是说**这一级根本没有把"慢下来"这个自变量推动起来** —— 所以它**不构成对 用户假说的检验** … 起身节奏由 `base_height_progress` 的逐步计酬决定(早站起来就多 拿),速度正则只在同一条时间轨迹上把动作抹匀,不改变何时站起来。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §25 R3.2(dof_vel −1e-3→−5e-3,慢一点起身) Every new penalty ships with a pre-registered withdrawal clause - if healthy gait must pay above the cap, the term stands down
calibration-threshold-with-withdrawal-clauseIntroduce every new penalty with: the zero-cost-option audit, a replay-calibrated weight formula (healthy pays a fixed small fraction of tracking), and a pre-registered withdrawal condition - and let the clause fire without argument when the calibration says the term cannot be afforded.
Symptom
Three same-shaped crashes had established a failure archetype: v4's clearance, v8a's landing window (weight off by 58x uncalibrated), and v6a's bare hip_yaw suppression all combined a zero-cost "don't move" option with a fee on any motion - a reverse barrier that pushes policies toward standing still.
Context
The v11 landing-window penalty was therefore introduced under a calibration-threshold protocol: (1) shape chosen with the window tightened (h_gate 0.03 -> 0.02, because 0.03 equaled the clearance target and priced the entire descent); (2) weight from a FORMULA, not judgment: measure the term's raw value on healthy replays (v5/v10b), set w = -(0.10-0.15 x tracking reward) / raw_healthy; (3) withdrawal clause pre-registered: if healthy gait must pay >15% of tracking no matter the tuning, the term is withdrawn to the next version rather than forced in - "不硬上". The companion hip_yaw quieting term ran the same protocol (calibrate on replays, healthy pays <=5%) and was later retired entirely when a structural fix (zero action scale) made its shaping tax unnecessary.
Change
Penalty introduction protocol: shape audit (what is the zero-cost option?), replay-based weight formula, healthy-pay cap with a written stand-down condition - all before training.
Outcome
The landing term was in fact withdrawn under its clause (v12 records "P5 落地窗口罚 已撤 … 维持撤下"), demonstrating the protocol firing as designed instead of the fourth same-type crash.
Mechanism
A penalty's damage mode is mispricing healthy behavior; since the healthy price is measurable in advance on replays, both the weight and the go/no-go decision can be computed rather than discovered by a ruined training run. The withdrawal clause converts "make it work" pressure into a clean deferral.
Applies when
- adding any motion-taxing penalty to a working gait
- a proposed term's weight has no measurement behind it
- a previous same-shaped term crashed training
“权重公式而非拍脑袋:先在 v5/v10b 回放上量 h_gate=0.02 的原始值,w = −(0.10~0.15 × 跟踪奖励) / raw_健康;标定门槛:若健康步态无论如何要付 >15% 跟踪,本项撤下留 v12,不硬上 (v4 clearance/v8a-B/v6a 三次同型翻车的教训:代价为零的"不动"选项 + 一动就收费 = 反向壁垒)。”
train/WALK_V11_SPEC.md § 6. P5 —— 落地窗口罚(三代欠账,标定门槛制) An edge-triggered landing penalty missed the tail and fired after the harm - penalize overspeed continuously inside the contact window
penalize-tail-before-touchdownPenalties aimed at impact/violation events must (a) price the excess over a threshold, not the mean, and (b) be active on the approach (state-gated window), not triggered by the event - check your control rate can even see the event you are penalizing.
Symptom
The v7 landing penalty (vz^2 on the contact-force rising edge, weight -10) did not bite: landing-velocity 95th percentile stayed at 2.61 m/s against a 0.3 target.
Context
Two structural faults were identified: (1) it penalized the MEAN over sparse events - many soft landings dilute the occasional violent slam, while the damage (GRF peaks, motor peak load) lives in the tail; (2) it fired AFTER touchdown - at 50 Hz evaluation the rising edge is aliased by physics decimation, so the read vz is often the already-decelerated post-impact value: underestimated, and with no shaping gradient before contact. Replacement: continuous penalty while the sole is inside a height gate (h < 0.03 m): relu(-vz - 0.30) - only the excess over an allowed approach speed is penalized (tail only), and gradient exists for several frames BEFORE touchdown. The sole-height computation again subtracts the 0.0585 m link offset ("WALK_DIAGNOSIS 坑#1, 别再踩"); the edge-triggered version was kept as a diagnostic only.
Change
feet_landing_vel reformulated: edge-event vz^2 -> in-window relu(-vz - v_ok) with v_ok 0.30 (conservative vs the sqrt(L)-scaled human value ~0.19, to be tightened after passing), h_gate 0.03, weight unchanged -10.
Outcome
The failure analysis of the first form was written before the second was trained; the v_ok escalation path (0.30 -> 0.45 if the robot becomes afraid to land) was pre-registered in the risk table.
Mechanism
Sparse-event mean penalties optimize the average case while the constraint is a quantile; and any penalty evaluated only at/after a discrete event gives the optimizer no gradient along the approach trajectory that determines the event. A state-gated continuous excess penalty fixes both: it prices only violations and shapes the approach.
Applies when
- impact/landing penalties fail to move tail percentiles
- a penalty is triggered by contact edges at a coarse control rate
- designing constraint-style penalties for rare violent events
“罚的是均值路径:上升沿是稀疏事件 … 大量软着陆稀释偶发猛砸;而伤害在尾部 … 罚在触地后:50 Hz 评一次,上升沿被物理 decimation 混叠,读到的 vz 常是撞完已减速的值——既低估,又没有触地前的塑形梯度。”
train/WALK_V8_SPEC.md § 2. 改动 B — 落地惩罚改罚尾部、罚在触地前 Decompose the offending quantity by channel first - then penalize the failure event, not the joints
penalize-the-slip-not-the-jointBefore penalizing motion to fix a side effect, measure which channels actually carry the offending quantity; prefer penalties conditioned on the failure event that are exactly zero for healthy behavior - and do not medicate behaviors that measurement shows are not sick.
Symptom
Heading drift with support-foot yaw slip (v5: 212-284 deg accumulated over 15 s); the previous v6 draft had attacked it by penalizing lateral joints (a roll 4.0 / yaw 2.0 "home" group) - which collapsed training into the standing basin.
Context
Before choosing the penalty target, the yaw angular momentum was decomposed by joint group with MuJoCo subtree_angmom weighted by real walking joint velocities: pitch-class joints (hip_pitch + knee) carry 95.3%, hip_roll 3.3%, hip_yaw 1.4%. The failed "home" group had been taxing 2.7/step to manage a 4.7% channel. The replacement, feet_yaw_slip (-0.2, |support-foot yaw rate| while in contact), targets the failure event itself and - decisively - costs a non-slipping gait exactly zero, which "横向回家组做不到". The same rung's do-not-do table applied the complementary principle to foot spacing: measured 196-214 mm, stable, no crossing - "没病不吃药" (no disease, no medicine).
Change
Removed joint-usage penalties for the drift problem; added the event-conditional slip penalty (-0.2, realized tax 0.141/step = 12% of tracking) alongside the existing linear-slip term.
Outcome
Turn-gain left/right difference improved 70% -> 19% and heading 185 -> 60.3 deg by v6 without a standing-basin collapse; the 2.7/step lateral tax never returned.
Mechanism
Penalizing joints taxes every use of a channel including healthy use, and if the channel carries little of the offending quantity the tax buys nothing while pushing the optimum toward immobility. An event-conditional penalty (slip while in contact) prices only the failure, leaving the healthy gait's cost surface untouched - and the channel decomposition tells you in advance whether a joint-side fix can even work.
Applies when
- choosing a penalty target for drift/slip/impact problems
- a proposed penalty taxes joints or motions rather than failure events
- a previous joint-penalty attempt collapsed the gait
“pitch 类 (hip_pitch + knee) 占偏航角动量 95.3% … hip_yaw 1.4% … 压 hip_yaw 是管 1.4% 的通道收 2.7/步 的税 —— 上一轮正是这样把策略推进了站立盆地。滑移项不惩罚走路: 不打滑的步态代价为零, 这是横向"回家"组做不到的。”
train/WALK_V6_MINIMAL.md § ① / ② 新增 feet_yaw_slip Borrow reward values from other robots as ratios (to tracking weight, to leg length) - never as absolute numbers
transfer-ratios-not-absolutesWhen importing any numeric from another robot's config or paper, identify its natural normalizer (tracking weight, leg length, sqrt(g*L), body mass) and transfer the dimensionless ratio; sanity-check against a same-scale robot when one exists.
Symptom
Published configs offered tempting absolute values (swing height target 0.06-0.08 m, weight -20) that would have been wrong for a robot with half the leg length and a different tracking weight.
Context
The cross-check normalized before transferring: G1's feet_swing_height weight -20 against tracking +1.0 is a 20x ratio, so with local tracking at 1.5 the equivalent is -30, not -20. G1's 0.06 m target on a ~0.70 m leg scales to ~28 mm on the local 0.325 m leg (Humanoid-Gym converts to ~23 mm), confirming the locally chosen 0.03 m and explicitly rejecting copying 0.05-0.08 absolutes. A same-class robot (Menlo's 16 kg) was used to sanity-check feet_air_time (+0.5 vs the local 2.0, flagged over-high). A nondimensional check of the same kind later validated the sidewalk speed target (v/sqrt(gL) = 0.081 vs hardware-verified 0.101 - 0.104 - inside the envelope, conservative).
Change
All borrowed values converted through ratios (weight/tracking-weight, height/leg-length, dimensionless speed) before entering the config.
Outcome
The scaled values worked (0.03 m target matched both the scaling law and measured 22-23 mm baseline); no cross-robot absolute was ever copied raw.
Mechanism
Reward economies are scale-relative (only ratios to the tracking term matter to the optimum) and kinematic quantities are morphology-relative (clearance scales with leg length, speed with sqrt(g*L)); absolutes encode the source robot's scale, ratios encode the design intent.
Applies when
- copying reward weights/targets from open-source configs or papers
- setting clearance heights, speed targets, or impact thresholds
- comparing your weights to published tables
“G1 的 feet_swing_height 是 tracking 的 20 倍(−20 vs +1.0)。我们 tracking 是 1.5,按同比例应为 −30 … G1 目标 0.06 m / 腿长 ~0.70 m,换算到我们 0.325 m 腿长约 28 mm;Humanoid-Gym 换算约 23 mm。故 target 取 0.03 m 是对的 … 不必抄 0.05~0.08 的绝对值。”
train/WALK_DIAGNOSIS.md § 修正 ②(权重放大) / 修正 ③(目标高度按腿长缩放) A curriculum ramp keyed to the process step counter re-fires on every resume - and shipped policies never saw the penalty
curriculum-counter-lineage-stepsKey every curriculum/ramp schedule to lineage-cumulative progress, not per-process counters; and audit where your shipped checkpoints sit relative to every ramp - a penalty that no product ever experienced is not part of your training.
Symptom
vx+0.30 died at a fixed relative time in every resumed run: resume at 500 -> slide at 1100, zero at 1300; resume at 700 -> slide at 1300, zero at 1500 - absolute depths offset by exactly the resume offset, relative timetable identical.
Context
ramp_reward_weight (the saturation penalty ramp) read env.common_step_counter, which restarts at 0 for every run including --resume. So start_step=600 meant "600 iters after THIS resume", not "lineage iteration 600". The A/B arm pair was the clean proof: their env.yaml differed only in log_dir, only resume point distinguished them, and the omni CurriculumManager had exactly one active term - nothing else could produce that timetable. Second consequence: every shipped checkpoint (s1e-500 at +500, C2-700 at +200, A800 at +100) was selected before its run's +600, so the saturation penalty weight was 0.000 for every product ever shipped - explaining saturation 33% and raw |action| 1.9 against clip 1.0 (hip_roll in bang-bang), i.e. half the heat budget.
Change
Two independent recommendations recorded: (1) make the ramp count lineage steps (add the checkpoint's iteration offset on resume) or pin terminal weights in downstream rungs instead of ramping; (2) give the saturation penalty its own rung - never mixed into a skill-learning rung (that would be two variables again).
Outcome
Explained the recurring +600 death of the highest-amplitude command and the persistent actuator saturation of all shipped products with one root cause; honest caveat booked (at +800 the weight is only -0.086, small, but vx+0.30 is the command demanding the largest action amplitude, so it is squeezed first).
Mechanism
Resumable training splits "the lineage" from "the process"; any schedule keyed to process-local counters silently re-applies its transient to every descendant run, and any product-selection habit that picks checkpoints early systematically samples the pre-ramp regime - the curriculum exists in the config but never in any shipped policy.
Applies when
- resumed/forked training with any scheduled reward or DR ramp
- a metric dies at a fixed offset after each resume
- shipped policies show behavior a late-schedule penalty should prevent
“ramp_reward_weight 读的是 env.common_step_counter，它每个 run 从 0 开始，--resume 也不例外。… 原始 run / 臂B | 500 | 1100 = +600 | 1300 = +800；臂A | 700 | 1300 = +600 | 1500 = +800 … 所有出品其实从没见过饱和罚。… 这解释了 sat_max_pct 33%、raw |a| 最大 1.9（clip 是 1.0）—— hip_roll 一直在 bang-bang，而罚它的那一项权重恒 0。热账的一半在这里。”
train/C_LADDER_RUN.md § 3g. 系统性问题：saturation_ramp 每次 resume 归零 A joint frozen at the action clamp pays zero action_rate forever - penalize pre-clip saturation to make the cheat cost money
saturation-cheating-zero-rate-costWhenever actions are clipped and any smoothness/rate penalty exists, add a pre-clip saturation penalty so living at the clamp costs more than oscillating - and audit for frozen-at-clamp joints (action std ~0, |a| at exactly the clip value) as a standing acceptance row.
Symptom
With action_rate_l2 raised to -0.2, walk_v7's hip_pitch actions froze at exactly +/-1.000 (the clamp), reproduced bit-for-bit on hardware (splits frozen at +/-0.35 rad); the gait-shaping term joint_pos_ref collapsed to 0.026-0.035. The repo had died in the same trap once before (walk_v0: four joints pinned at +/-1.0).
Context
Mechanism: a joint pinned at the clamp has action-rate cost exactly zero and forever zero - under a strong smoothness tax, "push to the clamp and freeze" becomes the dominant optimum. Lowering the weight (-0.2 -> -0.1) only reduces temptation; the frozen state still costs nothing, so the structural fix adds action_saturation = sum(relu( |a_raw| - 0.9)) at weight -1.0, computed on the PRE-clip network output - post-clip, |a|=1.01 and |a|=3 punish identically and the out-of-range gradient dies (v0's old disease: mean |a| 1.71 soaked in saturation). Economics: freezing at |a|=1.0 now pays 0.1/joint/step (two hips = 40% of alive) vs ~0.0004/step for the healthy reference oscillation - the cheat flips from free to ~250x negative. Honest limits were recorded: A1 does not forbid freezing at 0.89 (the anti-freeze pressure must come from the oscillation demand of joint_pos_ref), and the alternative "rate on post-clip target" was rejected as 换汤不换药 - a pinned target also has zero rate.
Change
v8-A: add action_saturation (-1.0, thresh 0.9, pre-clip) AND halve action_rate_l2 (-0.2 -> -0.1, still 3.3x the v5 value); success criterion pre-declared (joint_pos_ref telemetry returns to v6 scale).
Outcome
Booked as the structural repair of the v7 freeze; also fixed a config hygiene trap discovered on the way - action_rate was assigned twice in __post_init__ (v5 comment line then v7 line), merged to one assignment "别再留两处赋值给下次审计埋雷".
Mechanism
Clipping creates a zero-gradient, zero-cost absorbing region in action space; any penalty on action derivatives makes that region strictly optimal once entered. Only a penalty on clamp proximity itself (measured pre-clip so depth of violation is visible) restores a slope out of the absorbing region.
Applies when
- joints sit at exactly the action clip with near-zero variance
- raising a smoothness penalty degrades gait amplitude
- shaped-oscillation terms collapse after a rate-weight increase
“钉死在钳位的关节 action_rate 代价精确为零且永远为零;−0.2 之下"推到钳位冻起来"成了压倒性最优 … 本仓第二次栽在同一坑(walk_v0 死于四关节钉死 ±1.0)。回调权重(−0.2→−0.1)只降低诱惑不消除作弊 … 算在 clip 前的原始网络输出上 … 作弊收支从"白赚"变成"倒贴 ~250 倍"。”
train/WALK_V8_SPEC.md § 1. 改动 A — 治饱和作弊 Curriculum-gate a penalty to the phase where its disease occurs - early on it only taxes exploration
gate-penalties-to-the-disease-phaseFor penalties aimed at late-stage pathologies (freezing, saturation, degenerate attractors), ramp the weight in only after exploration noise has decayed; anchor the terminal weight to measured healthy-vs-sick raw values, and shift all related tripwires to after the ramp completes.
Symptom
The action_saturation penalty, applied from iteration 0 in v8a, taxed exploration itself: with init_noise_std 1.2 the sampled actions paid ~-2.45/step before any policy had formed - while the disease it targets (clamp freezing) is a LATE pathology (v9 froze at iteration ~2624).
Context
v10 re-introduced the same penalty behind a curriculum gate: weight 0 until iter 1000, ramping linearly to -1.0 by iter 2000 - present only when the disease can occur, absent while exploration noise dominates. The trust argument was evidence, not hope: in v8a the term, while active, had pulled joint_pos_ref from 0.041 up to 0.155 and climbing - proof it can extract a policy from the frozen pit. Weight magnitudes were anchored to measured raw values (healthy v5 0.310 / v6 0.106 vs frozen v7 1.145 / v9 1.22 per step: at -1.0 healthy pays 6-18% of tracking, frozen pays 60%+, standing ~0). v10c then isolated the gated term as THE anti-freeze mechanism by single variable, upgraded to untouchable status in v11: "S 的门控机制(v10c 单变量铁案:任何情况下 不许撤,只许调终值)" - and v11 dared to relax other penalties only because S stood guard.
Change
action_saturation gated 0 -> -1.0 over iters 1000-2000 (later terminal value tuned -1.0 -> -0.5 with the gate mechanism itself frozen); tripwires adjusted to respect the gate's timing (freeze check moved to iter 2500-3000 to give the ramped term its effect window).
Outcome
Freezing stopped recurring while early training kept full exploration; the mechanism graduated from experiment to invariant within two versions.
Mechanism
A penalty's incidence depends on who occupies its support: early in training that is exploration noise (whose suppression starves learning), late it is the converged pathology. Time-gating aligns the penalty's presence with its target's presence, buying the constraint without the exploration tax - and tripwire timing must then be computed from the gate schedule, not from ungated precedents.
Applies when
- a structural penalty punishes exploration in early training
- a late-onset pathology (freeze/saturation) needs a standing guard
- deciding when a curriculum ramp should engage
“v8a 实锤它的病根是"罚在采样动作上"——init_noise_std 1.2 的早期等于罚探索(~−2.45/步);而冻结是晚期病(v9 速率 2624 才死平)… 门控让它只在病发期在场。… v8a 里它在场时 joint_pos_ref 从 0.041 爬到 0.155 且仍在升——有从低谷爬出的实证。”
train/WALK_V10_SPEC.md § 2. S 保险 —— action_saturation 课程门控 Prove a new penalty actually fires - two ways a clearance term silently did nothing
inert-reward-term-auditBefore training with a new reward term, log its realized per-step value under the current policy and confirm it is nonzero where intended - check coordinate zero-points against FK and check who occupies the term's gate; and never weaken the term that creates the states your new term needs.
Symptom
A newly designed swing-height clearance penalty could have trained as a no-op twice over, and the companion advice to lower feet_air_time actively backfired when tried.
Context
Instance 1 (zero-point offset): the proposed code used body_pos_w of the foot link, but that is the ankle_roll_link frame origin, which sits 0.0585 m above the ground even with the foot flat on it - so (0.03 - 0.0585) is always negative and the penalty is永远 0; the 0.0585 offset must be subtracted (verified identical in MuJoCo FK and Isaac). Instance 2 (gate occupancy): the clearance penalty fires only in swing phase; a dragging policy keeps both feet in contact, so the penalty is constantly 0 for exactly the policy it was meant to fix - and worse, any slight lift immediately incurs it, a reverse threshold. Lowering feet_air_time to 0.5 on that advice measurably collapsed air time to 0.0002 (below v3). Corrected understanding: "clearance 是把已有的摆动相抬高, 造出摆动相仍要靠 air_time" - air_time creates the swing phase, clearance raises it.
Change
Fixed the height zero-point; kept feet_air_time as the swing-phase creator with clearance layered on top; both errors documented as corrections to the team's own earlier advice.
Outcome
With both fixed, swing height rose from 22-23 mm (v2) to 29 mm (v5) to 34 mm (v6); the inert-term failure class entered the standing checklist.
Mechanism
A penalty's gradient exists only where its gate is occupied and its argument crosses its threshold; frame offsets shift the threshold out of reach, and phase gates can have zero occupancy under exactly the policy being treated. Terms interact as an ecology - one term must create the states in which another can act.
Applies when
- adding any gated or thresholded penalty (clearance, impact, slip)
- a new term produces no behavioral change at any weight
- body-frame positions are used in reward code
“body_pos_w 是 ankle_roll_link 坐标系原点,平放触地时仍高出地面 0.0585 m。… (0.03 − 0.0585) 恒为负 → 惩罚永远是 0 … clearance 惩罚只在摆动相生效,拖地时两脚始终触地 → 惩罚恒 0;而一旦轻微抬脚就立刻扣分,对正在拖地的策略是反向门槛。… 正确认识:clearance 是"把已有的摆动相抬高",造出摆动相仍要靠 air_time。”
train/WALK_DIAGNOSIS.md § walk_v4 独立验收 — 本文档给的两处代码/建议是错的 Deployment power derating damages non-forward axes far more than forward - sweep it in sim before deploying
power-scale-hurts-nonforward-axesTreat deployment power/torque scaling as a plant parameter: evaluate the policy in sim at the exact deployment scale, expect non-dominant axes to degrade first under derating, and either deploy at the training power or train with power randomization.
Symptom
Policies deployed at power-scale 0.8 (a safety derating of commanded torque) looked fine walking forward but were weak at backward and turning, inviting the wrong diagnosis "the skill was not trained well".
Context
Measured repeatedly: on s1e, going 1.0 -> 0.8 cost forward 18% but backward 58%; on C4-ff800, turn tracking was +25%/+40% at pw0.8 vs +75%/+58% at pw1.0, backward 51-52% vs 97-103%, while forward stayed 96-98% at both. Sim evaluation numbers in the plan were all pw1.0, but the robot was being run at 0.8.
Change
Pre-deploy protocol added: sweep the exported policy across power in sim (for PW in 0.8 0.9 1.0: eval_c_matrix --power $PW --seeds 20) and deploy at the first level where both turn directions reach >=50%. For C4 the recommendation was raise the robot to pw1.0 - the sweep showed it nearly free (saturation 47%->33%, left foot-clipping danger zone 25%->6%, cost only tilt 6.7->8.3 deg).
Outcome
Turning "weakness" resolved without any retraining; the sim sweep correctly predicted the real-robot signature at both power levels.
Mechanism
Forward walking is the reward-dominant, torque-cheapest skill with the most margin; backward/turn/sidewalk live closer to the torque envelope, so a uniform torque derating consumes their margin first. Training ran at power 1.0 (the trainer does no power scaling), so deploying at 0.8 is a systematic underactuation the policy never experienced.
Applies when
- deploying with any torque/power derating or safety scale
- secondary skills (backward, turn, lateral) underperform on hardware while forward walking looks fine
- choosing the deployment power level for a new policy
“power 衰减对非前进轴的伤害远大于前进轴（s1e：前进 1.0→0.8 掉 18%，后退掉 58%）。转向是非前进轴，0.8 下很可能明显跟不动。”
train/C_LADDER_RUN.md § 3c. A-2 上机前先定部署力度档 / 3p. 二 Train with self-collisions ON (filtering nested-link ghost pairs) - the reward wall prevents, the physics makes cheating impossible
self-collision-physics-plus-reward-wallNever train a contact-risk behavior with self-collisions disabled; enable them with an audited filter list for nested/overlapping pairs (zero contacts across a pose sweep), record the fps cost, and keep a calibrated distance penalty as the preventive layer on top.
Symptom
walk_v8 logged 107 frames of leg-on-leg contact while still earning 0.751 tracking score - because training-side self-collisions were OFF, leg clipping was literally imperceptible to the policy ("碰腿在训练里 根本感知不到").
Context
Enabling self-collisions naively is its own trap: an Isaac audit had shown PhysX auto-filters adjacent bodies (base-hip clean for free) but nested links generate ghost forces - calf and ankle_roll overlap 65 mm at the zero pose, producing 12x body-weight phantom forces. The v10 recipe: enable self-collisions, explicitly filter only the two nested pairs (l/r calf-ankle_roll), then run a zero-contact audit at three poses (nominal stand, walk crouch, swing-extreme) requiring contact count = 0, adding any residual pair to the filter and re-auditing; a 500-iter sanity run for NaN and an fps-cost record (measured -8.8%). Redundancy with the reward-side foot-distance wall was argued, not assumed: "N2 离得远(奖励侧预防),SC 碰了疼(物理侧兜底)" - the reward keeps distance at range, the physics makes contact hurt - so the v8-style "clip legs and still score" outcome becomes physically impossible.
Change
enabled_self_collisions=True + 2-pair filter + three-pose zero-contact audit (re-verified at 0.00 N after the later mass update) + fps budget recorded.
Outcome
Leg contact entered the training signal; the audit protocol caught the nested-pair ghost-force hazard before it corrupted training; combined with the calibrated distance wall, later versions held contact = 0 on hardware and in sim.
Mechanism
A hazard absent from the training physics cannot be learned about, no matter the reward; but collision meshes that interpenetrate at rest inject large fictitious forces if enabled blindly. Filtered enabling plus a pose-swept zero-contact audit gives true contact physics with no phantom energy - and layering prevention (reward) with consequence (physics) covers both learning and enforcement.
Applies when
- real robot self-contacts while training scored it healthy
- enabling self-collisions on a model with nested collision meshes
- deciding between reward-side and physics-side fixes for clipping
“PhysX 自动过滤相邻体(base↔hip_pitch 免费干净),幽灵力只在 calf↔ankle_roll(零位嵌套 65mm,12 倍体重)。… 与 N2 互补不冗余:N2 离得远(奖励侧预防),SC 碰了疼(物理侧兜底)—— v8 那种 107 帧互碰拿 0.751 跟踪分的事从此物理上不可能。”
train/WALK_V10_SPEC.md § 4. SC —— 训练侧自碰撞(范围已探明,比想象便宜) Tightening the bridge's rate limiter under an unchanged policy cut torque peaks 30-50% and made other things worse - the policy cannot see the limiter, keeps commanding and winds up; a deploy-side limiter is a safety net, not a cure
deploy-rate-limiter-windupA rate or torque limiter added at deployment lowers peaks but the policy still commands as if unconstrained (saturation, windup, new contacts); use it as a safety net mirrored in evaluation, and put the constraint where the policy can learn around it.
Symptom
After the violent first real-robot get-up, the cheapest candidate fix was to tighten the bridge's slew (rate) limit for the recovery policy without retraining.
Context
Probe on R3.1 in MuJoCo (5 categories x 3 seeds, mu 1.0), monkeypatching the limiter with no repository change: TIGHT = RS06 4.0 / RS02 3.0 / RS00 2.0 rad/s (about 0.08/0.06/0.04 rad per policy step) against the current vel_limit setting.
Change
The probe decided the role of the limiter rather than a deployment.
Outcome
Success 14/15 -> 12/15; get-up median 2.35 -> 3.53 s (max 9.30); torque demand peak median hip_pitch 164% -> 111%, knee 166% -> 86%; action saturation still 100%; leg-leg contact 558 -> 860 frames. The limiter was kept only as a real-robot safety net (mirrored into sim2sim evaluation); the cure moved into training - where the next lesson was that a limiter anchored on the last command is itself an integrator (slew-anchor-is-an-integrator).
Mechanism
A policy that never trained with the limiter keeps issuing the targets it learned; the limiter clips them, the target window runs ahead (windup), and the robot follows a trajectory the policy never evaluated.
Applies when
- a trained policy is too violent on hardware and a quick deploy-side fix is tempting
- adding slew, torque or velocity limits in a bridge or firmware
- evaluation and deployment use different limiter settings
“判读:**链路侧收紧立等可取地把 τ 峰值砍 30~50%,但成功率掉、饱和率仍 100%、 腿-腿接触反升** —— 策略感知不到限速器,目标窗口继续狂奔。⇒ 收紧 slew 只配当 **真机侧安全网**(必须同步进 sim2sim 口径,基础设施现成),**不配当治法; 治法必须进训练**。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §26 探针:收紧桥层 slew,r3_1 不重训直接测 Every power cycle starts with the same read-only pre-flight - read the buses, check the torque limits against 12/17/11, verify the IMU axes, check the ports after any new USB device - and any reassembly re-measures the joint zeros
power-cycle-preflightStart every powered session with a fixed, read-only pre-flight - bus responses, torque limits equal to the simulated ones, IMU axes, device identities - and re-measure joint zeros after any mechanical reassembly before running a policy.
Symptom
Hardware state drifts between sessions in ways no policy can see: a motor that stops answering after a power cycle, a torque limit that differs from the one simulated, an IMU axis flipped, two USB devices swapping identities, a joint zero moved by reassembly.
Context
The runbook's session order before any policy runs: read every motor on both CAN buses without enabling them (the first command after every power cycle); set_torque --check, all twelve motors must read 12/17/11 N*m, and any difference is written back; imu_reader --verify-axes, where the operator tilts the robot forward and to the right and every check must pass before continuing; check_ports after plugging in any new USB device (the IMU and a CAN adapter once collided on USB identity). After re-mounting motors: read the buses, then re-measure the calibration offsets (three repeats, written back) - "skipping it means running everything on the wrong zero". Hanging checklists repeat the torque-limit check (the deploy script also self-checks at start).
Change
A fixed, read-only pre-flight run in the same order every session.
Outcome
The runbook records one earlier hardware check in the same spirit: all 12 motors' implied kp fell within 18.4-22.0 for a commanded 20, inside the kp randomization range used in training.
Mechanism
A policy transfers only if the plant matches the one it was evaluated on; the pre-flight turns silent hardware drift into a failed check before the robot moves.
Applies when
- the first command after powering a robot on
- after swapping adapters, cables or motors
- a policy that worked last session suddenly behaves differently
“python tools/set_torque.py --check # 12 颗应全对 12/17/11, 有 diff 就 --write … 插任何新 USB 设备后都先跑一次 check_ports.py(IMU 和 CANable 的 USB 身份撞过车) … python tools/calib_stance.py --repeat 3 --write # 重标 offset —— 8/9/10 重新装, 机械零位变了”
RL系统/FOLLOW THIS copy 2.md § WALK / STAND 每次开始前 / 换CAN / 装回后必做两件 Two simulators disagreed 1.8x on one policy's torque demand - four explanations were eliminated with numbers, the surviving suspect was never tested, and neither reading was allowed to cancel the other
torque-disagreement-between-simulators-unresolvedWhen two simulators disagree on a safety-relevant quantity, eliminate the measurement explanations one at a time with numbers, name the survivor as a hypothesis, keep the pessimistic reading binding, and run the direct test (replay one action sequence open-loop through both plants) before the quantity is used to pass a gate for hardware.
Symptom
For R3.0, Isaac read hip_pitch torque demand at 75-80% of the limit (PASS); MuJoCo read the same policy at 148-152% (1.5x over the limit).
Context
Candidates were eliminated one by one: PD gains (identical, RS06 kp 30 / kd 1.5), the settle window (both skip the first 0.5 s), the statistic (worse-of-two-legs vs per-joint - explains ~15%), self-collision (the no-contact subset still read 152%), sampling (500 Hz peak vs 50 Hz sample - ~9%). About 1.8x remained. The prime suspect - Isaac's implicit actuator (PD solved inside the PhysX integration, chosen to mimic kHz firmware PD) against MuJoCo's 500 Hz explicit PD - was named but untested.
Change
The Isaac PASS was recorded as valid for the Isaac plant only; the prescribed decider was an open-loop replay of one action sequence through both plants, compared step by step, needing no training. It was upgraded to a precondition of R3.1.
Outcome
R3.1 ran in parallel with, not after, the replay, and the replay never appears as done. By §40 it was "the oldest open account" on the line, to be fed by real-robot logs - which the spec also never records. Meanwhile the 50 Hz sample under-read the peak by 34% as smoothing narrowed the spikes, so Isaac-side readings grew more optimistic exactly when the comparison mattered more.
Mechanism
Each measurement artifact explained a slice of the gap; what remained is a plant difference, and an untested plant hypothesis cannot license discarding the pessimistic simulator on a safety-relevant quantity.
Conflicts
The spec prescribes the open-loop replay (§23), upgrades it to an R3.1 precondition, then records that R3.1 ran in parallel without it (§24), and lists it as the oldest open account before hardware (§40); nothing through §50 (2026-08-14) records a result. Every later "torque gate PASS" on this line is an Isaac-plant reading plus a MuJoCo check, never a reconciled one.
Applies when
- Isaac and MuJoCo (or sim and hardware) report different torques, contacts or slips
- implicit vs explicit actuator models are in play
- a gate passes on one simulator only
“**同一个策略,一侧判 PASS 一侧判超限 1.5 倍。** … 口径项全部扣掉后仍剩 **~1.8×** 没有解释。 … 但**这条没有验证,不能拿它当结论去抵消 MuJoCo 的读数**。 … (做法:拿同一条 动作序列在两边开环回放,逐拍比 τ —— 不需要重训)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §23 MuJoCo 复核门:成功率更稳,但 τ 与 Isaac 差 ~1.8× 没收敛 Anchoring the action on the measured joint angle (target = q + beta*a), with a beta curriculum down to tau_limit/kp, bounded torque by construction, removed the re-falls and later stood the robot up on hardware
beta-anchored-action-targetFor large-motion skills on position-controlled actuators, bound the action relative to the measured joint angle with a per-joint authority of tau_limit/kp, curriculum the authority down from full range, keep the curriculum state out of the observation and pin acceptance at the deployed authority - and make the deployment code refuse to run the anchored contract without a measured q.
Symptom
The V0 full-range absolute action produced violent targets; the V1 command-anchored rate limit made standing oscillate. Both failure modes came from how the action becomes a target.
Context
V2.0 (user approved, from scratch): BetaAnchorJointPositionAction, target = q_measured + beta_j(m)*a, memoryless per step. beta_j(m) = floor + m*(beta0 - floor), beta0 = the contract half-range (m = 1 reproduces V0 authority), floor = min(tau_limit/kp, beta0): hip_pitch 1.309 -> 0.40, knee 1.047 -> 0.40, hip_yaw -> 0.917, the other joints unchanged - the tightening lands exactly on the joints the V0 torque account convicted. m drops 0.1 per step when a standing-share EMA exceeds 0.35. beta is NOT in the observation, so the 45-dim contract is untouched; acceptance is pinned at m = 0 because the Python curriculum state is not saved in the checkpoint. The deployment chain got a new profile (recovery_v2: action_anchor current_q, explicit per-joint beta written into the contract, independent of the gain profile), and policy_io raises if q is missing rather than silently falling back to the absolute contract; the old profile's check reproduced its pre-change deviation bit for bit.
Change
New action term and beta curriculum; later the RS06 floor was lowered 0.40 -> 0.30 -> 0.25 (kp*beta 7.5 N*m) and the stamped deployment profile was synced to 0.25.
Outcome
First acceptance at m = 0 (v2_0b): re-falls 0% in every category, the torque gate passed for the first time on the line (worst 69.9%), knee jitter 0.004; supine 98.8 / side 88.8% with prone and mid still failing (fixed by the conditional pull curriculum). MuJoCo showed demand at or under the limits (hip_pitch 11.7/12 against V0's 26.8). Lowering beta cut impact (hip_pitch demand 9.7 -> 8.5 N*m) but barely slowed the get-up - it had become coordination-limited. Enabling the policy moves the target only +/-beta around the current pose, so there is no homing fling; the 08-11 real get-up and the later v3_1p1c both run on this contract.
Mechanism
kp*beta caps the proportional torque in a single step with no build-up delay and no memory, giving both a hard impact bound and full balance bandwidth.
Applies when
- a skill needs full joint range but hardware torque limits are low
- absolute position targets cause impacts or saturation
- changing the action semantics of a contract that deployed policies share
“**动作项** `BetaAnchorJointPositionAction`:`target = q_实测 + β_j(m)·a`, 逐步无记忆 … **Play/验收钉 m=0(= floor = 部署档)**:python 课程状态不进 checkpoint, Play cfg 显式 `beta_m_start=0` … 判读:**结构赌注兑现** —— 站姿零再摔 + 力矩账首过(kp·β 封顶按构造)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §33 V2.0 预注册(2026-08-10,用户点头开工):β 锚定动作空间,从零训 Prove an armless get-up exists before training it - a connected static domain, 25% torque on the cheapest path, an 8 mm hand-over gap, a static roll-over - and write down what each scan cannot represent
get-up-feasibility-accounts-before-trainingBefore training a get-up or any multi-contact skill, compute the quasi-static accounts - connectivity of the static domain, torque along the cheapest path, hand-over gaps, COM shift available for rolling - and state which configurations each scan cannot represent; when a policy gets stuck in one of those, extend the scan before blaming the reward.
Symptom
A torso-and-legs robot has no arms to push off the ground; whether it can get up from the floor at all was unknown when the line opened.
Context
recovery_feasibility.py ran three accounts before any training (the run line's "hard accounts first" discipline): a sagittal quasi-static scan (0.05 rad grid, 44,520 configurations, MuJoCo FK, flat-foot assumption). (1) The static standing domain (COM over the feet, torques in limit) has 29,586 cells, flood-fill connected with no islands, from a 0.097 m deepest squat to the 0.384 m stand. (2) The minimum-torque path peaks at 25% of the limits (knee 2.9/12, ankle 3.7/17 N*m) - a 4x margin. (3) All 508 ground-contact configurations have the contact behind the COM; the smallest gap to pure foot support is 8 mm. A roll-over account: swinging both straight legs to one side shifts the COM 96 mm against a 62 mm torso half-width - 1.6x, so rolling needs no momentum. Three conclusions were written down for later attribution: the legs are 80% of the mass (swinging them moves the COM), prone has no flat-foot hand-over face (merge into a supine/side sit first), and supine needs no sit-up (hip flexion is limited to 75 deg).
Change
The accounts gated opening the line and were cited in every later argument about what the robot can physically do.
Outcome
They held where they applied: in V1.0 every fall category was righted under a hard rate limit, which the spec records as the quasi-static roll-over account verified by training, and the 25% torque path was the basis for pursuing a slow get-up. They also misled once: account (3) is sagittal, and on 08-09 the spec corrected its scope - it cannot represent the splayed W-sit where the policy actually stalled. A follow-up prone hip-ROM scan (471,625 cells) found 3,912 two-foot-contact cells and none with both soles within 25 deg of level (best 40.2 deg): a flat-footed push-up from prone is infeasible on this robot, so the fix became where the feet go after sitting up.
Mechanism
A get-up needs a connected path through statically feasible configurations and enough torque along it; quasi-static accounts bound both cheaply, and momentum can only make the real problem easier. A reduced-dimensional scan, though, only speaks for the configurations it can express.
Conflicts
In R0.1-R0.2 the spec read account (3)'s "prone has no front hand-over" as "prone lacks the roll-over skill"; R0.3's confusion matrix showed prone had righted its torso 159/159, and the spec then restricted account (3) to the sagittal configurations it models.
Applies when
- opening a get-up, recovery or climbing skill on a new robot
- a robot lacks arms or other obvious contact options
- a policy stalls in a configuration a feasibility scan never modelled
“本机 **torso + legs、无手臂可撑地**,开训前先证明存在不依赖手臂的物理解 … 双腿同侧直腿摆最大横移 **96 mm = 1.6×** … **静态摆腿即可翻身,无需动量**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §1 机械可行性判决(2026-08-09,recovery_feasibility.py 三笔账) Oversized lateral COM randomization (+/-5 cm) deliberately forces leg spread
com-randomization-forces-leg-spreadDR ranges can be behavior-shaping tools, not just robustness padding: oversize a randomization axis to force a strategy the reward struggles to express - and expect a compensating behavior to appear as the cost.
Symptom
Feet drift toward the centerline and even collide; policy has no incentive to keep a lateral support base.
Context
COM randomization ranges were chosen asymmetrically by axis: lateral +/-5 cm ("比常规大，故意的" - larger than usual, on purpose), fore-aft +/-2 cm, vertical +/-2 cm. The oversized lateral range is not robustness padding but a behavioral forcing function. Lucen logged it as directly relevant to its own roll-channel / sideways leg-kick symptom.
Change
Set COM randomization to lateral +/-5 cm, fore-aft +/-2 cm, vertical +/-2 cm, with the lateral band intentionally oversized to make narrow stances fail during training.
Outcome
Effective at separating the feet on the reference robot; side effect - the base began swaying left-right, which then required a foot-centerline distance penalty (see reward-chain-foot-height-landing-spacing).
Mechanism
Randomizing COM laterally makes narrow-stance policies fall for some draws, so PPO discovers wide stances as the only strategy robust across the band - DR used as an implicit reward. The sway side effect appears because the policy hedges against unknown COM by active lateral correction.
Applies when
- feet too close / self-collision in a learned gait
- roll-axis instability suspected to come from narrow stance
- choosing COM or mass-offset DR ranges
“两脚太近甚至互撞 → 先试质心横向随机化 ±5 cm，逼迫策略把脚分开；有效但引发新问题——基座开始左右摇摆 … 横向 ±5 cm（比常规大，故意的，用来逼出分腿）/ 前后 ±2 cm / 垂直 ±2 cm”
Experience.md § 质心随机化范围 (lines 75, 84-86) The walking lines' safety setting, power-scale 0.8, broke the recovery policy's full-range contract - it cut the ends of the joint travel (4/50 could not get up) and left the torque spikes untouched; a kp x 0.9 gain profile inside the trained kp band did the job
power-derating-cuts-full-range-contractA deployment derating knob means something only relative to the action contract: before reusing a line's "safe setting" on a new skill, check what it does to that skill's reachable range and to the term that makes the spikes, prefer a gain change inside the band the policy was randomized over, verify it in simulation, and re-decide when the contract changes.
Symptom
After the violent first real get-up (2026-08-09), the recovery policy needed a gentler setting for its next hardware test, and the walking and omni lines' standard derating - deploying at power-scale 0.8 - was the obvious candidate.
Context
The V0 recovery contract maps actions to absolute targets over the full joint range: a = +/-1 lands exactly on the URDF limits, and standing puts the knee at the clip. Candidates were compared on R3.1 in MuJoCo (5 categories x 10 seeds) on 2026-08-10 before any hardware time was spent.
Change
A new gain profile, rl_kp090 (kp x 0.9, kd unchanged), recorded in robot.yaml as the recovery hardware-test setting, with power-scale 0.8 explicitly banned for recovery.
Outcome
kp x 0.9: 48/50 got up; median torque demand on hip_pitch/knee fell from 120-125% to 100-104% of the deployment limit; leg-leg contact frames 2,152 -> 1,095; the change sits inside the +/-10% kp randomization the policy trained with. power-scale 0.8: 4/50 could not get up, because under the full-range contract it removes the ends of the travel (the deep squat's tucked legs, the straight standing knee), and the torque spikes (kp x error) did not fall at all. When the line moved to the beta-anchored contract, rl_kp090 was declared a V0-era choice that does not fit (beta is calibrated at kp 30) and deployment returned to rl_default; the deploy switch applies power scaling to the walking side only.
Mechanism
A power scale multiplies the action, which under an absolute full-range mapping shrinks the reachable workspace instead of softening the actuator; the spikes come from the proportional term on large errors, which only a gain change reduces - and a gain change inside the trained randomization band stays in distribution.
Conflicts
The undated operator runbook still carries an R3.1 "B comparison" command at power-scale 0.8 beside the rl_default baseline; the sources do not say whether it was written before the ban or was ever run.
Applies when
- reusing a power, torque or action scale from one skill on another
- a policy whose actions map to absolute targets over the full joint range
- choosing a gentler setting for a first or second hardware trial
“kp×0.9 / kd 不动 —— recovery_r3_1 成功 48/50, τ 需求中位 hip_pitch/knee 120~125% -> 100~104% 部署限, 腿-腿接触 2152 -> 1095 帧; ±10% 在训练 kp DR 带内. ⚠️ power-scale 0.8 对 recovery **禁用**: 全 ROM 契约下 0.8 砍的是行程 端点 (深蹲收腿/站直够不到), 实测 4/50 起不来, 且尖峰 (kp·err) 一点不降 —— 它是 walk/omni 的安全档, 不是 recovery 的.”
git:Lucen-recovery@origin/recovery:robot.yaml § gain_profiles 注释: recovery 真机测试安全档 (2026-08-10) / rl_kp090 The +/-50 mm lateral COM randomization meant to spread the legs coincided with legs pulling IN - rolled back per its own pre-registered contract
com-dr-rollback-on-symptomWhen adopting a DR value that covers no local measurement, write its intent and rollback trigger into the config at adoption time; roll it back as the control arm the moment the symptom contradicts the intent, and promote the symptom's metric into the acceptance battery.
Symptom
After v7 adopted the reference developer's oversized lateral COM randomization (+/-50 mm) explicitly to force leg spread, the real robot's legs narrowed instead - lateral mean 154 mm / closest 107 mm in sim (nominal 214.5), narrower still on hardware with occasional leg contact.
Context
The rollback was clean because the adoption had been honest: the robot.yaml comment recorded the intent AND that the +/-50 value covered no local measurement (only a 16/7 mm measured offset existed; even the prior widening to +/-20 was subjective), plus the reference's own reported side effect (base sway) and the note "这一项要单独跑、 单独归因". When the opposite symptom appeared, v8 returned y to +/-20 mm as the control arm ("要么没起作用、要么帮了倒忙 … 按约定退回做 对照"), kept x/z untouched (a noise-level difference not worth another variable), and named the second suspect: the landing penalty itself, via the reference's own three-link chain (landing penalty -> stance narrows -> spacing penalty needed). A gate lesson was booked in the same table: v7's sim numbers had ALREADY crossed the line (154/107 vs v5's 182/147) - "这个指标本可拦下 v7" - so foot-distance became a standing acceptance row (min >120 mm, zero leg-leg contacts).
Change
base_com_offset_m y: 0.050 -> 0.020 (x/z kept), regenerated through the export tool rather than hand-editing derived files; foot-distance acceptance row added.
Outcome
A borrowed DR lever with no local measurement basis was retired the moment its symptom contradicted its purpose, at single-variable cost; the metric that would have caught it pre-hardware entered the gate.
Mechanism
DR ranges shape behavior through the policy's robustness strategy, which is jointly determined with every reward term; a lever that forces stance width on one robot can be dominated by a stronger narrowing pressure (landing softness) on another. Levers adopted without local measurement must carry their own rollback trigger, because there is no nominal to argue from when they misbehave.
Conflicts
Causality is not fully closed in the source: the narrowing may come from the landing penalty rather than the COM lever ("腿距的第二嫌疑人是 ④ 本身"); the rollback is the pre-agreed control experiment, not a verdict that the lever caused the narrowing.
Applies when
- importing DR ranges or behavioral-forcing randomizations from references
- a DR lever's observed effect contradicts its documented purpose
- a sim metric existed that would have caught a shipped regression
“⑥ 的本意 … 是逼策略把脚分开;真机结果是脚向内收且偶发相碰——要么没起作用、要么帮了倒忙。… 注释当时就写了"这一项要单独跑、单独归因"。现在症状出现了,按约定退回做对照。”
train/WALK_V8_SPEC.md § 3. 改动 C — 质心随机化退回(撤销 v7-⑥ 的 y 项) The first real-robot get-up was "very violent, kicking on the floor, dangerous" - a sim-perfect policy with no reason to be slow, unbounded absolute targets, no domain randomization and a rate limiter that filtered nothing; the task was restated as "safe, slow, transferable"
first-real-get-up-violent-stage-one-policyDo not put a get-up policy on hardware until its action is bounded (hard bound or state-anchored targets), smoothed, randomized and tested at the real pipeline's latency, and say explicitly that the task is "safe, slow and transferable" - a simulation-perfect policy optimizes only "gets up".
Symptom
On 2026-08-09 the user ran a V0-lineage recovery policy on the real robot and stopped it: very violent, kicking on the floor, dangerous. The planned next rung (a heavier torque_headroom) was never started.
Context
The spec had pre-registered that R0/R1 products stay in simulation and that the real-robot precondition was the R3 smoothing rungs plus a bridge-slew check plus a hanging protocol; the robustness (DR) rungs had not run. In simulation the policy passed 100% with a get-up of about a second. Which ONNX, which gain profile and whether a torque/joint log existed were left "to be recorded later" and never were.
Change
The V0 ladder was stopped at its best product (R3.1, sim only) and a re-rooting proposal was put to the user. The spec's four-layer account: style (the reward pays for standing early and nothing pays for slowness - HumanUP's "Stage I" get-up, "fast but unsafe ... infeasible for real-world deployment"); impact (full-range absolute targets with no hard bound, raw |a| up to 4.77, action saturation 100%, a single-step change of 0.306 saturating hip_pitch); transfer (zero DR, friction pinned at 1.0, the learned leg bracing); link (the bridge's RL slew equals vel_limit, 0.2-0.66 rad per step, while the real pipeline has 1-2 steps of time-varying latency and acceptance ran at delay 0).
Outcome
The line was re-rooted twice (training-side rate limit, then the beta-anchored action space) and gained a hang protocol before the next real attempt; on 08-11 a beta-anchored policy produced the line's first real get-up.
Mechanism
A task reward that pays for standing early selects the fastest feasible get-up; with absolute full-range targets every large target jump is a torque impulse bounded only by the clip; zero DR and braced-leg solutions do not transfer; and a limiter set at the velocity limit does nothing at 50 Hz.
Conflicts
The four layers are the spec's reconstruction from simulation probes and the literature; the real run's policy file, gain profile and log were never recorded, so no layer was confirmed against hardware data.
Applies when
- a first hardware trial of a high-effort skill is being scheduled
- sim success is high but the policy saturates actions or torques
- pre-registered hardware preconditions are not all met
“用户真机反馈:**非常猛、地上乱踢、危险**,叫停(R3.3 torque_headroom 加档已选型 weight −0.5→−1.5,未启动)。真机细节(哪个 onnx、什么档、有无 τ/q log)**待补记** … 任务从"能起来"变成 **"安全、慢、可迁移"** … **链路层**:桥层 slew RL 档 = vel_limit(10/20/33 rad/s ≈ 每拍 0.2~0.66 rad), 对 recovery 形同虚设;真机 1~2 拍时变延迟,验收默认 delay 0。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §26 真机叫停与换根判决(2026-08-09) The real robot's right-leg kicking was over-trained-delay times loop gain - irreducible pipeline latency is plant, model it fully from day one
pipeline-latency-is-plant-not-drMeasure the end-to-end action pipeline delay and build it into the nominal plant and every acceptance gate from day one; treat power/scale deratings that "fix" oscillation as gain-reduction crutches flagging an unmodeled delay, and expect higher-feedback-gain policies to be MORE delay-fragile.
Symptom
On hardware, s1c/s1d at action scale 1.0 always kicked wildly with the right leg (s1c only ran as SOTA at power 0.8; s1d only at 0.7) - while sim showed nothing under default evaluation.
Context
Sim reproduced the incident item by item once the real pipeline delay was injected: s1d@1.0 with --delay 1 fell at 10.2 s, --delay 2 at 5.2 s; s1c@1.0 stressed (r_hip_roll saturation 5 -> 16%; "右脚" = the policy's chirality makes the right leg its high-gain leg); and the combos that worked on hardware (s1c@0.8+delay2, s1d@0.7+delay2) all survived in sim. Mechanism: the real pipeline is ~1-2 ticks (BusWorker next-cycle pickup + CAN round trip) but S1.1 trained only to 1 tick - "超训延迟 × 全环路增益 = 振荡;衰减 = 压环路增益换稳定" (delay beyond training x full loop gain = oscillation; the power derating had been buying stability by compressing loop gain). s1d was MORE fragile than s1c because its yaw 3-layer stack had learned higher feedback gain - higher gain, lower delay tolerance. Three changes: latency DR widened to cover reality; acceptance gates and smoke runs moved permanently to --delay 2 ("门必须在真机条件下预测 真机"); and the doctrine written twice-paid: "不可约的管线属性(延迟、 限速)不是'随机化选项',是 plant 本体,第一天就该全额建模" - S1's nominal-then-robust staging falsified by hardware for the second time. The later s1e hardware run at power 1.0 (no kicking, normal force) closed the loop: "0.8 = 旧代拐杖" - the derating had been a crutch for the under-modeled delay, not a real requirement.
Change
Latency modeled as plant from day one of any lineage (measured 1-2 ticks covered, bridge-layer rate limits likewise modeled by default); every gate and smoke evaluation issued under --delay 2.
Outcome
Kicking reproduced, explained, and eliminated in the s1e generation at full scale and full power; the deploy-side crutches (0.7/0.8) retired for the new lineage.
Mechanism
Feedback oscillation onset is a product of loop gain and phase lag; a policy trained below the real delay learns gains that sit past the real stability margin, and any output derating masks it by scaling gain down. Since pipeline delay is deterministic hardware property - not an uncertainty - it belongs in the nominal plant, and every evaluation must include it or the gate predicts a robot that does not exist.
Applies when
- hardware oscillation/kicking that sim only reproduces with added delay
- a policy only runs on hardware at reduced power/scale
- defining what belongs in the nominal plant vs the DR list
“真实链路延迟 ~1~2 拍 … S1.1 只训到 1 拍——超训延迟 × 全环路增益 = 振荡;衰减 = 压环路增益换稳定。s1d 比 s1c 更脆 = yaw 三层栈学出更高反馈增益,增益越高延迟容忍越低。… 教训入账:S1「先标称后鲁棒」第二次被真机证伪——不可约的管线属性(延迟、限速)不是"随机化选项",是 plant 本体,第一天就该全额建模。”
train/OMNI_V0_SPEC.md § 3. S1.4(真机右脚乱踢事故强制) Drop the frozen policy into chosen configurations - a squat 2.7 cm lower than the stuck pose stood 52% of the time, the stuck W-sit 0%, and the interpolation between them showed a wall, not a slope
configuration-probe-wall-not-slopeWhen a policy is stuck, probe the frozen policy from a grid of hand-placed start configurations, including interpolations between the stuck state and a nearby state it escapes from; one read-only experiment separates height, torque, sampling and configuration and tells you whether to prevent entry or train the exit.
Symptom
After R0.3 the policy stood from 62% of starts and never from the W-sit it fell into; height, torque, missing samples and reward were all plausible suspects.
Context
A read-only probe placed the R0.3 policy directly into specified configurations. Squats (hip, knee, ankle) = (-.65,-1.3,-.65) stood 100%, (-1.0,-2.0,-1.0) 89.8%, (-1.2,-2.4,-1.2) at 0.176 m 52.3%; the measured W-sit at 0.203 m 0.0%; the account-(3) hand-over state (146 deg tilt) 34.4%; linear interpolations from the W-sit toward the squat at 25/50/75% stood 0.0/0.0/3.1%. The squat family's quasi-static torque is 16% of the limits, and the W-sit was visited ~9 s per episode in training. FK showed the squat family (-a,-2a,-a) keeps the torso vertical, the feet flat and the COM over the feet all the way from 0.146 m to 0.384 m.
Change
Height, torque and sampling were eliminated in one experiment; the next rungs targeted entering the W-sit (foot placement) instead of escaping it, and seeding the dead point itself was ruled out because it was already visited every episode.
Outcome
Pure configuration: the W-sit (hips externally rotated +/-47 deg, knees folded 110 deg, shins flat, feet beside the body) is a different place from the sagittal squat (feet flat under the COM). The policy's standing skill was bound to a narrow sagittal family, and the wall was confirmed by the interpolation. The foot-placement rungs that followed took prone from 0/159 to 158/159.
Mechanism
A learned skill covers the neighbourhood of the states it succeeded from; a start state outside that neighbourhood fails regardless of height or torque, and an interpolation that stays at zero until close to a working state shows the boundary is sharp.
Applies when
- a policy stalls in a specific posture and several causes are plausible
- deciding between reverse-curriculum seeding and entry-prevention shaping
- a feasibility account says a path exists but the policy does not take it
“**决定性对比:比死点矮 2.7 cm 的蹲姿站立 52.3%,死点 0.0%。** 所以不是高度、 不是力矩(蹲姿族准静态力矩膝 1.96/12、踝 1.24/17,只占 16%)、也不是训练采样 (死点每局被访问 ~9 s)。**是纯位形问题** … 插值实验进一步显示这**不是坡是墙** —— 走到 75% 仍只有 3.1%”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §15 死点位形实验(只读探针,同一个 R0.3 策略放进指定位形) A hardware run without its log is an anecdote - the first real get-up's policy, gain profile and log were never recorded, two CSVs stayed "to be reported", and runbook commands wrote different policies' logs under one copied filename
hardware-log-is-the-attribution-inputMake the log part of the run: name it from the policy and conditions automatically (never by hand-copied filenames), record the policy digest and gain profile inside it, include what the open questions need (torque, joint positions and targets), and treat a session without a collected log as incomplete.
Symptom
The recovery line's oldest open question - whether Isaac or MuJoCo reads torque demand correctly - was waiting on real-robot logs that never arrived, and the verdicts that did arrive could not be tied to files.
Context
deploy_policy writes a CSV per run (--log); the runbook's own analysis snippet reads its joint-position, target and action columns (q_, tgt_, act_), and the recovery hanging checklist asks for torque and joint logs for the whole run, to be compared with simulation. The first real get-up (08-09): policy, gain profile and log "to be recorded later". The first real A/B (08-11): v2_5b's result and both policies' CSVs "to be reported". In the runbook's walking commands, three runs of two different c4 policies log to real_s1e_pw08_teleop_0808.csv, and s1e and s2e_fric runs log to real_c2_700_pw08_teleop_0808.csv - filenames copied from other commands.
Change
None recorded; the spec kept listing the open-loop comparison as waiting for real logs.
Outcome
No real-robot log appears in the recovery spec through §50, so the simulator disagreement stayed unresolved and hardware verdicts stayed unattached to data.
Mechanism
Attribution needs the run's identity (policy digest, profile, conditions) and its signals in one artifact; a filename copied from another command mislabels the file, and a log not collected at the session is rarely collected later.
Applies when
- planning a hardware session whose result should settle a sim question
- log filenames are typed or pasted by hand
- hardware feedback arrives as prose without files
“python tools/deploy_policy.py --policy train/policies/omni_c4_ff800_pj.onnx … --log train/real_logs/real_s1e_pw08_teleop_0808.csv … q,t,a=d[:,c("q_")],d[:,c("tgt_")],d[:,c("act_")]”
RL系统/FOLLOW THIS copy 2.md § Walk 遥控 / S2 / csv 分析片段 (operator runbook, undated) Before training a one-leg stand, the accounts and a probe showed the default gains could not hold it at all - kp 20 needs 0.39 rad of error to carry the static roll moment, more than the whole adduction range - so per-joint gains came first, and thermal limits set the session length
single-support-gain-authority-probeBefore training a posture that loads one joint statically, compute the steady tracking error load/kp and the series stiffness against m*g*h, and prove with a simple hand-written controller that the posture can be held under the deployment gains - change the gains first if it cannot; then size session length from the thermal account.
Symptom
The one-leg line (standing on one foot, the other folded back, no hopping) had to decide whether the existing gain profile could hold single support before any reward was designed.
Context
Hardware accounts (9.792 kg, COM 0.234 m high, 170 x 80 mm feet, legs 80% of the mass): moving the COM over one foot needs 107 mm of shift and the 20 deg hip-roll adduction range gives 131 mm - geometrically enough. The static frontal moment is 7.8-9 N*m, within RS02's 17 N*m - torque is enough. But at kp 20 carrying 7.8 N*m needs 0.39 rad of tracking error, more than the entire adduction range, and the real robot had already shown it: commanded +0.17, actual -0.04 (0.21 rad droop) under load, 0.0008 rad hanging - load, not the motor. A probe (probe_oneleg.py) then showed open-loop PD cannot hold single support on physics grounds, so the criterion became "an equilibrium exists and a hand-written 4-gain COM feedback can hold it": single-support roll stiffness is hip and ankle in series and must exceed m*g*h_com = 22.5 N*m/rad; ankle kp 12 in series with hip kp 80 gives only 10.4 (open loop 16/16 fell), ankle 60 with hip 80 gives 34.3 (52% margin).
Change
A per-joint gain profile (rl_oneleg: hip_roll kp 80, ankle_roll kp 60, the rest as rl_default) - which needed per-joint gain support in robot.yaml, the bridge, deploy and the trainer's actuator groups - decided before training. Thermal account: single support makes hip_roll the dominant heat load (about 7.8 N*m against a 7 N*m continuous rating), so acceptance and demos run in segments of at most 60 s with a temperature check.
Outcome
Under rl_oneleg the hand-written feedback held six cells cleanly for 6 s (hip_roll steady torque 2.1-3.4 N*m, half the thermal budget); under rl_default the same feedback on the same cells fell 0/4. The trained V0 policy then passed its 40-cell acceptance.
Mechanism
With PD position control, the steady error needed to carry a static load is load/kp; when that error exceeds the joint's range the posture is unreachable whatever the policy does, and series compliance between joints lowers the effective stiffness below the gravity stiffness that single support demands.
Applies when
- single-support, crouched or one-arm-load postures on PD actuators
- a joint "droops" under load on hardware but tracks well when hanging
- deciding whether a new skill needs its own gain profile
“但 kp=20 时撑住 7.8 N·m 需要 **0.39 rad 跟踪误差 > 整个内收行程**。真机已实测: 命令 +0.17 实际 −0.04（droop 0.21 rad），悬挂时 0.0008 rad——是负载不是电机。 … 单支撑滚转是 hip/ankle **串联**刚度，必须 > m·g·h_com = 22.5 N·m/rad；ankle kp12 串 hip80 只有 10.4（开环 16/16 全摔），60 串 80 = 34.3（裕 52%） … **rl_default 同反馈同格 0/4 全摔**（增益档必要性对照）”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §1-1 单脚站: 几何可行，卡点是 hip_roll 增益权限 / §2 A 线增益 / §5 probe 定谳 Knee swing collapsed because it directly trades against the slip penalty - price the conflict explicitly and clamp what reward cannot hold
knee-swing-vs-slip-pricingWhen a behavior collapses as another metric improves, look for the term pair trading them and set their price ratio deliberately (with escalation and reverse tripwires pre-registered); where the policy actively spends action budget to undo your target, stop paying more reward and clamp the target space structurally.
Symptom
Knee peak-to-peak swing collapsed across generations - v5 33 deg, v10 26-30, v10b 7-8, v11 6.5-8.6 - and rolling the clock back did not recover it, acquitting the clock; the collapse tracked the gated slip penalty instead: "屈膝与不打滑在当前奖励里直接对抗" - v10b's excellent 93 deg slip was purchased with knee amplitude.
Context
Reward-side flexion fixes had failed three times: raising reference amplitude backfired twice (v9/v11), and v11's deep-squat default was actively fought by the policy - it spent 0.68 of action budget pulling the squat straight ("被策略花 0.68 动作拉直反杀"). v12's design accepted the conflict as real and attacked on two tracks: (1) ECONOMICS - a direct knee_swing_amplitude reward (+0.3, target 0.55 rad, capped at 0.6/step = 55% of tracking), explicitly opposed to the slip penalty by design ("显式对立——这正是设计:v12 就是这场对抗的定价实验"), with an escalation ladder (K +0.3 -> +0.5, then slip -0.5 -> -0.3, one layer at a time) and a reverse tripwire (slip telemetry back at v10 levels -> slip weight to -0.8, accept ~20 deg knee compromise); (2) STRUCTURE - knee target bounds [0.2, 0.9] rad so full straightening is physically impossible (straightest 11.5 deg) and the 0.68 fighting budget is released. A bonus falsifiable prediction was attached: phase-lock strength tracks amplitude (v9_probe 48 deg locked 2.5 Hz; v11 low-amplitude 1.36 Hz unlocked), so if K works, hardware phase-lock should return - one change, two verdicts.
Change
knee_swing_amplitude reward + knee target clamp + pre-registered escalation/reverse levers; the failed reward-side-only approach retired.
Outcome
The lineage was frozen before v12 trained (strategic reset), but the diagnosis stands as the walk line's clearest example of two reward terms trading a behavior between them, with the pricing experiment and structural clamp fully designed and calibrated.
Mechanism
When two terms price opposite aspects of one motion (swing amplitude creates yaw momentum that becomes slip), the optimizer settles wherever the price ratio puts it - patching one side moves the equilibrium, not the conflict. Explicit pricing makes the trade a designed quantity; structural clamps remove the regions where the policy spends budget fighting the designer.
Conflicts
The pricing experiment (K vs slip) was designed and calibrated but never trained - the 2026-08-05 reset suspended v12; the collapse attribution table and the 0.68-action counterattack are measured, the remedy's效果 is untested.
Applies when
- one gait quality degrades in lockstep with another's improvement
- the policy visibly fights a default pose or reference
- repeated reward-side fixes for the same behavior have failed
“膝摆塌在 v10→v10b,头号嫌疑是门控滑移罚(四代实测膝 p2p:v5 33° / v10 26~30° / v10b 7~8° / v11 6.5~8.6°;退时钟没救回 → 非时钟)——"屈膝"与"不打滑"在当前奖励里直接对抗 … 奖励侧修屈膝已三败 … v11 深蹲 default 被策略花 0.68 动作拉直反杀”
train/WALK_V12_SPEC.md § 0. 定位 / 2. K —— 膝摆经济(与滑移罚的对偶) Four in-lineage attempts to widen the standing stance failed - remove a tax, add a joint-space knife, change the target, add a task-space metric penalty - because the stance was the end state of the get-up path; trained from scratch with the right terms it grew right from day one
stance-decided-by-get-up-pathA posture a skill ends in is shaped by the path the policy takes to reach it; if several single-variable edits to the terminal-phase reward cannot move it, stop editing that phase and retrain with the terminal constraint present from the start.
Symptom
v2_6c stood with its feet 0.159 m apart (task-space) and its hips yawed 45-47 deg the same way, which split on the real robot. Standing-phase reward edits did not move it.
Context
V2.7-A removed the flat-feet tax on compensated stances (stance unchanged); V2.7b added a hip-roll lower-bound hinge (+5 deg in 3,000 iterations, yaw ratchet); V2.8 changed the stand_pose target to a wide flat stance (stance unchanged, yaw not unwound, feet nearly overlapping, mu 0.4 transfer 2%); V2.9 penalized lateral spacing in metres (the policy parked just outside the penalty's gate in a lunge, 0% success). The v2_6c get-up goes through a split and closes the feet together as it rises.
Change
In-lineage stance surgery was formally closed. V3.1 trained from scratch with task-space stance terms present from the first iteration (and, after P1, a positive width band instead of a penalty).
Outcome
V3.1 P1b: lateral stance 0.364 m, foot tilt 0.0 deg, all four categories 100%, MuJoCo mu 1.0 and 0.4 both 100% - with a symmetric toe-out the kinematic audit had not enumerated. P1c (with a yaw guard): 0.355 m, all six acceptance criteria passing, mu 1.0-0.4 all 100%; it became the product.
Mechanism
A converged policy does not rebuild the path that produced its terminal posture; a standing-phase gradient only finds the nearest hack around the posture the get-up delivers.
Applies when
- the final posture of a transition skill is wrong and resists terminal-phase shaping
- repeated continuation rungs produce hacks instead of the intended posture
- deciding between another in-lineage fix and a from-scratch retrain
“窄站距 + yaw 扭是 v2_6c 起身策略(劈叉起身 → 双脚并拢收势)的**结构性 终态**,不是站立段的孤立参数 —— 站立形态由起身路径决定,在血统内只动 站立段奖励改不动它。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §44 结果:V2.8 判 FAIL —— 血统内站姿手术第三次证伪 A binary reward band on the swing knee had zero gradient everywhere below it, so the one-leg policy parked in an unloaded "fake touchdown" that Isaac's 5 N threshold scored as success and MuJoCo showed as real pressing - a capped constant-gradient ramp, retrained from scratch, passed 40/40
binary-band-reward-fake-touchdownShape approach-to-target rewards as capped ramps with gradient from the starting posture, never as bands or indicators; and compare contact-based terms across simulators, because a policy riding just under a force threshold looks perfect in one and wrong in the other.
Symptom
At iteration 1,000 of the first one-leg run the swing foot never lifted: the policy stood with the "raised" foot resting lightly on the ground. In Isaac the contact-match term paid 96% of full marks; the same policy in MuJoCo pressed that foot on the ground for 450 frames.
Context
The swing-leg goal was "shank folded fully back" (knee 1.5-1.95 rad), rewarded as a binary band: +0.8 inside [1.5, 1.95], zero elsewhere. From knee 0.05 to 1.5 rad the term was flat. Contact is judged at a 5 N force threshold, so a foot carrying less than 5 N counts as lifted. The walk line had hit the same disease with a binary indicator (v4) and fixed it with a capped ramp (knee_swing_amplitude).
Change
swing_knee_fold changed from the binary band to a ramp clamp(|q|/1.5, 0, 1) - a constant gradient capped near 86 deg - and the policy was retrained from scratch (V0r1). After the first real-robot try showed the fold still too low, its weight went 0.8 -> 2.0 (V0.1).
Outcome
V0r1 model_2300 passed the full acceptance 40/40 (swing knee 1.72 rad, about 98.5 deg) and was stamped as oneleg_v0.onnx; the cross-simulator disagreement is recorded as the thing that caught the cheat.
Mechanism
A reward that is flat until the target is reached gives no gradient to approach it, so the policy settles for the nearest state other terms reward - here, a foot that satisfies the contact threshold without lifting; a second simulator with different contact force resolution exposes such threshold-riding.
Applies when
- rewarding a posture target with an in-band / out-of-band indicator
- a contact threshold decides whether a foot counts as lifted
- trainer-side contact terms are near full marks while the video looks wrong
“初版二值带 [1.5,1.95] 在膝 0.05→1.5 全程零梯度，策略停在"卸力虚点地"（Isaac 5N 阈下 contact_match 96% 满分 / MuJoCo 同策略 450 帧实压——跨仿真器互证抓作弊）；v4 二值指示同型病，按 knee_swing_amplitude 判例改常数梯度封顶 ramp，从零重训 … **oneleg_v0.onnx = V0r1 model_2300, 40/40 PASS**”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §4 奖励表 swing_knee_fold 行 / §8 核查单 5 A policy's gain profile is part of its contract - the one-leg policy needs per-joint gains the default profile lacks, and the manifest refused an evaluation under the default once; the recovery contract's beta was never stamped, a known gap not to repeat
gain-profile-belongs-in-the-stampStamp everything that defines the closed loop a policy was trained in - gains included - into its manifest, and make every consumer refuse a mismatch; a profile field that is not in the stamp is a silent misconfiguration waiting for an operator to forget a flag.
Symptom
A policy trained with hip_roll kp 80 and ankle_roll kp 60 behaves differently, or falls, under the default kp 20/12 profile - and the gain profile is a command-line flag an operator can forget.
Context
The one-leg line added a gain_profile field to the contract so the stamped manifest carries it; the spec's deployment note says the manifest guard blocks rl_default and that it had already bitten once in simulation (an evaluation run without the one-leg profile). The same spec states the general rule - any new profile field must be synced into the manifest builder - and names the counter-example: the recovery line's beta was never put into the manifest. The recovery line itself had decided that its anchored authority is computed from the base rl gains and written into the contract so it cannot drift with the gain flag, and that the older kp x 0.9 profile chosen in the V0 era does not match the beta contract and must not be used.
Change
Gain profile as a contract field checked at load; per-contract gain choices written into the run sheets.
Outcome
Evaluations and hardware runs of the one-leg policy run under rl_oneleg or are refused; the recovery beta gap stayed recorded as known.
Mechanism
A policy is trained against a closed loop whose gains are part of the plant; running it under other gains is an out-of-distribution plant, exactly like a wrong observation scale.
Applies when
- a skill introduces per-joint or skill-specific gains
- deployment gains are chosen by a command-line flag
- adding any new field to a policy profile
“增益档 `--profile rl_oneleg` 必须给 —— manifest 防线会拦 `rl_default`（sim 已咬合一次） … （recovery 的 β 未进 manifest 是已知缺口，不再复制）”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §9b AGX 真机手顺 要点 / §3 契约 Real-robot trials of a new skill were staged by risk - a hanging dry run with the robot posed by hand, then one short try per category on a mat with the hardest last, then the composed behaviour (switch + walking) last - with the user present and a log every time
staged-hang-mat-floor-for-get-upStage a new skill's hardware trials by risk - hanging dry run posed by hand, one short try on a mat per start category with the hardest last, the composed behaviour last - with an operator ready to cut enable and a log for every try; relax a safety ban only for short, attended runs and say so in writing.
Symptom
A get-up policy acts violently near the ground by design, and the first unstaged real run of the line was stopped as dangerous.
Context
The hanging checklist written with the first stamped recovery product (v2_5, 2026-08-11), to be ticked item by item with the user present: both machines on the same commit and firmware torque limits checked; the robot hung from a single point about 0.1 m off the ground; a dry run with the robot posed by hand into supine and prone to watch that the target stream is gentle (the beta contract keeps targets within +/-0.25 rad of the measured pose, so enabling causes no homing fling); the first floor try is supine only, on a mat, once, with torque and joint logs; categories are added one at a time, prone last; any kicking or oscillation cuts enable immediately. For the switch (08-14) the runbook orders: hang with the standing policy as the locomotion side, then on a mat push the robot over and let it recover, and only last swap in the walking policy. An exemption was also written: edge-standing policies stay banned from long or unattended runs, but a short single A/B with the user present, hung or on a mat, is allowed. The one-leg line reused the same order (hang, then floor with a spotter, 60 s segments with a temperature check).
Change
Real trials as a checklist of stages, each gated on the previous one, with the composed behaviour last.
Outcome
The line's first real get-up (v2_6, 08-11) came through this protocol and was reported "fairly stable"; no further hardware outcomes of the switch are recorded in the spec.
Mechanism
Each stage exposes one new risk (commanded targets without contact, a single category with contact, harder categories, then the interaction of two policies), so a failure is attributable and cheap.
Applies when
- first hardware trial of a recovery, jumping or other high-impact skill
- switching between two policies on hardware for the first time
- a policy with a known posture defect needs a comparison run
“吊挂空跑: 手动摆到 supine/prone 姿态, 看目标流是否温和 (β 帽 7.5 N·m, 目标永远贴着当前 q ±0.25 rad —— 使能瞬间无归位甩动, 这是 β 契约附带保证) … 落地首试: supine 一类, 垫子, 单次; τ/q --log 全程记录 … 逐类别扩展 (prone 最后), 每类先单次”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §40 吊挂执行单(真机首试;需用户在场,逐项打勾) FK-verify a borrowed reference's structure, then size its amplitude by the reference's job - it pins phase, the policy adds lift
reference-structure-fk-amplitude-divisionWhen borrowing a reference trajectory: verify its structural claim against your own kinematics (an invariant like flat-foot), assign it the phase-pinning job, and size amplitude low enough that the policy contributes the lift - moving toward a proven foreign value in halves, not jumps.
Symptom
walk_v4 had big knee swing (40-46 deg) but only 18-24 mm foot lift - amplitude without hip/knee/ankle phase coordination; later, walk_v5's real-robot swing ballooned to 73.6 deg (sim 55.7) with violent footfalls - amplitude over-driven by the reference.
Context
Structure first: Humanoid-Gym's 1:2:1 hip:knee:ankle reference was verified on the local model before adoption - the ratio exactly satisfies the locally derived flat-foot constraint hip - knee + ankle = 0, FK-tested at multiple amplitudes with sole pitch 0.00 deg throughout. Amplitude second, and here the first reasoning failed honestly: FK said shorter legs need LARGER reference scale (0.30 for 30 mm lift), and the FK was correct - but the premise was wrong ("FK 没错, 但前提错了"): it assumed foot lift must come from the reference. HighTorque Pi, same scale, uses 0.08 with a 0.02 m foot-height target - proof that lift is added by the policy ON TOP of the reference, whose actual job is pinning the phase relationship. Scale 0.30 made the reference the entire gait: over-constrained and over-driven. The correction went to 0.15, deliberately not Pi's 0.08: "一次只走一半, 留退路" (walk half the distance, keep a retreat).
Change
target_joint_pos_scale 0.30 -> 0.15 as one of v6-minimal's three changes, treating both the footfall force and the lateral kicking (yaw momentum scales with leg swing amplitude).
Outcome
v6 improved landing force 1.72x -> 1.55x, suspended tilt 45.9 -> 23.0 deg, turn-gain asymmetry 70% -> 19%; the later v6-halved-shaping experiment (35 mm -> 4 mm collapse) confirmed the reference still carries the gait's existence on this machine - the division of labor is real but machine-specific.
Mechanism
A joint-space reference plays two separable roles: encoding structure (phase relations that keep the foot flat) and injecting amplitude (energy). Structure transfers across robots and is checkable by FK against an invariant; amplitude is a negotiation with the policy, and over-assigning it to the reference removes the policy's freedom to modulate lift with state.
Applies when
- importing a reference gait / imitation target from another codebase
- reference amplitude reasoning based on leg length alone
- real swing amplitude far exceeds sim's under a strong reference
“FK 没错, 但前提错了。我默认抬脚必须由参考轨迹产生。HighTorque Pi 同尺度机器人 … 用 0.08, 而它 target_feet_height = 0.02 m —— 说明抬脚是策略在参考之上加出来的, 参考只负责钉住髋/膝/踝的相位配合。我们取 0.30 等于让参考本身就是整个步态, 过约束 + 过驱动”
train/WALK_V6_MINIMAL.md § ① target_joint_pos_scale 0.30 → 0.15 A walking policy's tilt cutoff is a legal state for a recovery policy - the default 45 deg fall guard had to be raised for recovery tests and is disabled once the switch owns falls, so the abort chain becomes the recovery timeout, the operator's cut, and the firmware torque limits
fall-guard-becomes-a-stateWhen a new skill makes a safety cutoff's trigger a legal state, replace the cutoff with a bound of the skill's own (a timeout ending in a safe stop) instead of just switching it off; keep the operator's cut and the firmware limits as independent layers, and write every flag change into the run sheet.
Symptom
deploy_policy's default protection stops the robot beyond 45 deg of tilt. A recovery policy starts lying at roughly 90-97 deg, so under the default it is refused on the spot - a flag the first hanging checklist forgot.
Context
The layers in the sources: deploy_policy's tilt cutoff (default 45 deg, a line in the safety chain); for standalone recovery tests the cutoff was raised (110 deg in the spec's A/B sheet; 181 deg, effectively off, in some runbook commands); with --recovery-policy the cutoff is disabled because a fall is now a state, not an exception, and RECOVERY lasting over 15 s ends in a safe stop (the runbook calls it the line where the spotter steps in). Independent of the policy: firmware torque limits checked at start (12/17/11 N*m, set_torque --check), the operator cutting enable at any kicking or oscillation, and in the one-leg teleop a space-bar stop that puts the foot down.
Change
The flag was added to the run sheets, and the FSM replaced the removed cutoff with its own bound (the timeout).
Outcome
The spec records the flag omission and its fix; it does not record the FSM's timeout being exercised on hardware.
Mechanism
A safety cutoff encodes one policy's notion of "abnormal"; a new skill whose normal operation lies beyond it either cannot run or runs with the cutoff off, and only a replacement bound keeps the chain closed.
Applies when
- deploying recovery, fall-damage or acrobatic skills behind existing safety checks
- a run sheet disables a protection flag
- listing the abort chain for a hardware session
“--max-tilt-deg(默认 45°,安全链第 13 行写的那个)。recovery 的合法状态覆盖整个倾角域,把它抬到 181 = 实效关闭 … RECOVERY 超时 15s 会自动安全停(看护介入线)”
RL系统/FOLLOW THIS copy 2.md § FSM 吊挂首测 ② 落地测 / #### Recovery Policy (operator runbook, undated)