Training Coach
Doctrine
A report may cite any of these as doctrine-N.
doctrine-1Contract freeze and fingerprint disciplineThe policy I/O contract (observation layout, scales, history semantics, action pipeline) is frozen and fingerprinted; every exported policy is stamped and verified; contract changes ship as new versioned profiles that leave old artifacts bit-identical, and old policies run forever under their era's pinned profile.
Case. The 215-dim omni contract was frozen with a three-machine digest; the one contract-level extension (lateral feed-forward) went in as a new `omni_ff` profile with the old profile provably untouched, and the contract checker caught two real wiring bugs before any training (`contract-freeze-and-checker`). A silently changed gait-clock default would have fed old policies a 25% slower clock - closed by pinned legacy profiles (`legacy-profile-pinning`). A stale derived USD forked plant mass 2.2% until an automated source-vs-derived instrument gated it (`derived-asset-staleness-check`). A gain profile is part of the closed loop a policy was trained in and belongs in its stamp; the recovery line's anchored authority was left out of its manifest and recorded as the gap not to repeat (`gain-profile-belongs-in-the-stamp`), and a second policy behind a deploy-side switch made the handoff state itself a contract (`recovery-two-policies-and-a-state-machine`, `walk-recovery-fsm-handoff`).
Coach application. On any proposal touching obs/action semantics, defaults, or derived assets: demand the version/profile plan, the fingerprint update, and the checker extension in the same change; flag any old artifact that would run under new defaults.
doctrine-2Attribution by resolved training params - never eval-override knobsCapability differences between lineages are explained only by digging each lineage's *resolved* training configuration and eliminating columns; evaluation-side override knobs (kd-scale, power-scale, cycle-time) act on the plant for *every* policy and may serve as deployment mitigations but never as explanations.
Case. Low-friction robustness across 8 lineages x 3840 cells was traced to kd DR *bandwidth* - every lineage had ground friction pinned to (1.0,1.0), so "trained friction" could not be the axis; the parameter axis and the plant axis were explicitly separated after the first attribution conflated them (`kd-bandwidth-mu-law-attribution`). "Weak turning" on hardware was a power-scale plant effect, not a training gap (`deploy-knob-attribution-before-retraining`); slowing the deploy clock was out-of-distribution, not a feature (`cycle-time-override-is-ood`). The ground truth for what a run trained under is the logged per-run config, not the source tree (`resolved-config-is-source-of-truth`).
Coach application. Whenever asked "why is lineage A better", require the resolved-param table first; kill zero-variance columns; refuse explanations phrased in eval-knob terms; when a knob helps, label it deployment mitigation.
doctrine-3PASS gates become constraints; FAIL gates become objectivesOnce a skill passes its gate, that gate converts into a standing regression constraint (budget <= 2/20 against the parent baseline) for all later training; gates currently failing are the only legitimate objectives of the next rung.
Case. The C ladder ran one frozen 13-cell x 20-seed matrix at every rung with promotion = "new skill PASS and old skills within regression budget"; C1 was stopped and re-rooted precisely because it trained away the root's backward PASS (`fixed-acceptance-matrix-per-rung`, `preregistered-stop-criteria-per-rung`). The C4 product shipped only at 260/260 cells with zero regression.
Coach application. Keep the ledger: every PASS adds a constraint row; propose rungs only against FAIL rows; treat any constraint violation as stop-and-attribute, never "the next rung might win it back".
doctrine-4One variable per ladder rung - counted against what the checkpoint sawA rung changes one variable, where "one" is counted against the checkpoint's actual training state, not against the current config's diff; batching is allowed only when each change owns a disjoint symptom space with a pre-registered ablation order.
Case. Two rungs failed identically because resuming s1e-500 under the evolved config silently added four plant variables the checkpoint had never seen ("单变量纪律不只看「我改了什么」,还要看「checkpoint 见过什么」" - `resume-state-dr-audit`). v8 legally batched four orthogonal fixes with a written ablation order (`orthogonal-batch-with-ablation-order`); v9 spent one run completing a 2x2 factorial so either outcome convicted a factor (`fill-the-missing-factorial-cell`); v10b's three-way ablation wrongfully convicted the clock and had to be retried fairly.
Coach application. Before any resume: diff cfg against the checkpoint's logged training state. Before any batch: require the symptom-ownership map and ablation order in writing.
doctrine-5Pre-register risks, readings, and stop criteria before the ladderBefore a ladder or risky rung, write down the known risks, the interpretation of every plausible outcome, and hit-any-one stop criteria - frozen before training, tightened when priors say results should come fast.
Case. The C ladder opened with three numbered risks including the exact falsification condition for its own root choice; A/B arms carried "预注册读法(事后不改)" tables; a level expected to fail was run anyway for its pre-registered diagnostic value (`preregister-risks-and-fork-readings`). Stop criteria caught C4-redo rungs at +200 instead of full caps (`preregistered-stop-criteria-per-rung`); hardware sessions pre-registered per-config expected signatures and the disagreement rule "不改结论改账" (`preregistered-real-expectations`, `feasibility-accounts-lock-design-point`).
Coach application. Refuse to open a rung without the written risk/reading/ stop block; after results, read conclusions off the pre-registered table and flag any post-hoc reinterpretation.
doctrine-6Plant parameters are measured, never inventedEvery plant number carries measurement provenance: armature = N^2 x rotor inertia from no-load tests, friction split by rig and by API column, torque limits shaped by per-joint gait peaks, latency traced through the real pipeline, masses weighed - and DR bands are additive around the measured nominal, sized to the measured dispersion.
Case. Guessed friction was 2.5x low and guessed damping 5x high (`friction-measured-not-guessed`); armature had been 0 with a 9:1 gearbox (81x reflected inertia, `armature-n2-rotor-inertia`); a uniform torque derating was "the wrong shape" vs measured peaks (`torque-limit-shape-by-measured-peaks`); the delay implementation itself was a wrong plant for a whole lineage (`latency-lerp-reverse-extrapolation`); the run design point was locked by three accounts including the tau_limit/kd speed ceiling (`feasibility-accounts-lock-design-point`); identified friction had to land in the right simulator API columns to act at all (`sim-api-friction-columns`). The recovery and one-leg lines opened with the same kind of accounts before any reward existed - a connected static path and the torque along it for an armless get-up, and the gains single support needs to be holdable at all (`get-up-feasibility-accounts-before-training`, `single-support-gain-authority-probe`).
Coach application. For any plant value in a config review, ask "measured how?"; reject absolute ranges with no nominal; check API column mapping and derived-asset regeneration whenever measured values land.
doctrine-7Sim2sim gate before sim2real - under deployment conditionsEvery checkpoint passes a second, independently built simulator before hardware, and both the gate and the smoke loop run under the measured deployment conditions (real pipeline delay, honest contact parameters, the deployment gain/power profile).
Case. The standing order "先sim2sim 再sim2real" (`sim2sim-gate-before-sim2real`); acceptance flipped to match hardware only under measured condim/torsional friction (`eval-plant-honesty-contact-params`); gates moved permanently to `--delay 2` after the kicking incident (`pipeline-latency-is-plant-not-dr`); and the harness itself must be audited - a frame-convention bug in the cross-sim evaluator invalidated a whole line of verdicts (`body-frame-velocity-api-audit`). The recovery line's second simulator caught a torque penalty paid for by bracing the legs together (`torque-penalty-bought-by-leg-bracing`), and a 1.8x torque disagreement between the two plants stayed binding because its one surviving explanation was never tested (`torque-disagreement-between-simulators-unresolved`).
Coach application. Block any hardware request lacking a second-sim PASS at deployment conditions; when sim2sim and training-side metrics disagree, treat the evaluator as a suspect too.
doctrine-8Observation honesty - the actor's inputs are a hardware contractThe actor observes only signals the real robot produces with realistic noise; privileged truths go to the critic; history windows are estimators and must train under plant variation; rewards on quantities the actor cannot observe buy only average suppression, never closed-loop correction.
Case. Ground-truth velocity/forces went critic-only (`observation-honesty-critic-only`); frame_hist under zero DR memorized the trainer's plant fingerprint - 0/20 transfer (`history-obs-needs-plant-variation`); world-frame yaw rewards could not teach pull-back because heading is unobservable to the actor - correction was routed to the deploy outer loop instead of breaking the contract (`reward-observability-limit`, `deploy-heading-loop-and-align-training`).
Coach application. Audit every actor-obs element for hardware existence; require minimal plant jitter whenever history/recurrence exists; for each reward, ask "can the actor see this error?" and route correction tasks to outer loops.
doctrine-9Reward economics are audited in realized currencyReward design decisions are made on realized per-step magnitudes under the actual policy and command distribution: price the do-nothing optimum before adding a mode, compare achieved values to the computed ignore-floor, calibrate thresholds between measured healthy and sick distributions, and ship every new penalty with a withdrawal clause.
Case. feet_air_time at weight 2.0 realized 0.038 vs tracking 1.2 - drag was rational (`realized-contribution-audit`); ignoring a vy command cost 28-180x less than ignoring vx until a gated tracking term was added (`reward-cost-of-ignoring-audit`, `gate-new-reward-terms-by-command`); achieved-vs-floor separated "never learned" from "priced out" (`ignore-floor-diagnosis`); the foot-distance wall was placed between measured healthy (0.6% tax) and sick (55%) policies (`calibrate-threshold-between-healthy-and-sick`); the landing penalty carried a pre-registered stand-down condition and actually stood down (`calibration-threshold-with-withdrawal-clause`); two clearance terms were inert until zero-points and gate occupancy were checked (`inert-reward-term-audit`). A get-up policy sat because three gated terms paid the seated pose 84% of the return and the one term that could tell sitting from standing was an exp kernel reading 4.6e-5 at the real error (`seated-basin-dead-exp-kernel`); a torque-tail term was weighted by its measured steady value beside a peer term after the estimate proved 12x off (`tail-torque-needs-hinge-on-computed-demand`).
Coach application. Never discuss weights in the abstract: demand the realized-contribution table, the ignore-floor number, and the healthy-pay calibration before any reward edit is approved.
doctrine-10The zero-cost option must be the desired behaviorFor every penalty, name what the zero-cost option is; penalize failure events (slip, saturation excess, contact in flight windows), never the motion or joints that healthy behavior uses; make degenerate strategies fatal via termination where penalties cannot price them out.
Case. Joint-usage penalties for drift taxed a 1.4%-of-momentum channel 2.7/step and collapsed training; the slip penalty costs a non-slipping gait exactly zero (`penalize-the-slip-not-the-joint`). A frozen-at-clamp joint pays zero action-rate forever - only a pre-clip saturation penalty flips the cheat economics (`saturation-cheating-zero-rate-cost`). Ungated phase shaping made standing 42x more expensive than stepping and cooked the hip motors (`moving-gate-42x-stand-tax`); crouch-shuffling lived until a height termination deleted it (`termination-closes-degenerate-basin`). A gated penalty is an exit: the policy parked just outside an uprightness gate, then just under a height gate, to stop paying a stance tax, and only a positive band plus an always-on guard closed both (`penalty-gate-is-an-escape-hatch`); a soft-limit penalty that charged the standing pose itself bought a 4.1 deg lean (`soft-limit-penalty-charges-nominal-pose`); an unpriced foot attitude was spent on edge-standing (`unpriced-foot-attitude-is-a-free-variable`); and the one-leg line listed its cheapest cheats before training and still met one through a zero-gradient band (`enumerate-cheapest-cheats-before-training`, `binary-band-reward-fake-touchdown`).
Coach application. Run the "零代价的选项是什么" audit on every proposed term; convert motion taxes into event-conditional penalties; check the termination set against each known degenerate strategy.
doctrine-11Measurement discipline: independent referees, signs, distributionsA disputed measurement is adjudicated only by an independent algorithm from raw state; directional ability requires sign-antisymmetry under command reversal; bimodal metrics are reported as mode shares (never medians, never 3 seeds); ratios are not comparable when totals change; reward values compare only within one command distribution; single chaotic events never cross machines.
Case. The triple reversal - a good metric was "refuted" by a sibling metric that shared the disease (`independent-referee-for-metric-disputes`, `body-frame-velocity-api-audit`); same-signed +/- responses were bias, not turning (`same-sign-response-is-yaw-bias`); the swing median sat in a bimodal gap (`median-hides-bimodal-distribution`); "v6 is jitterier" died on absolute energies (`ratio-metrics-need-absolute-check`); yaw gain measured 15x wrong in an oscillating frame (`heading-integral-not-body-rate`); a 44% improvement evaporated under same-distribution comparison (`same-distribution-reward-comparison`); drift direction was a limit cycle (`multiseed-sign-test-for-drift`); a cross-machine push cliff was chaos (`single-impulse-recovery-is-chaotic`).
Coach application. Before accepting any surprising number: ask for the independent recomputation, the sign pair, the distribution shape, and the comparison conditions. Retract in writing when a metric falls.
doctrine-12The deployment pipeline is plantIrreducible pipeline properties - action latency, rate limits, power/torque scaling, teleop command mappings - are part of the nominal plant, modeled from day one and reproduced in every gate; deploy-side scalings are crutches that flag unmodeled plant, and they cannot be algebraically folded into training constants.
Case. Right-leg kicking was over-trained-delay x loop gain; power 0.8 was a gain-reduction crutch that retired when the delay was modeled (`pipeline-latency-is-plant-not-dr`); power derating damages non-forward axes first (`power-scale-hurts-nonforward-axes`); training at 0.4 scale as the "twin" of deploying 0.5 x 0.8 collapsed 0/20 (`deploy-scaling-not-training-equivalent`); one shared teleop speed sent an out-of-band lateral command and the robot clipped its own foot (`teleop-command-band-per-axis`); the latency DR range had not even covered the measured pipeline (`latency-dr-covers-measured-pipeline`). A rate limiter added at deployment only clipped a policy that kept commanding (`deploy-rate-limiter-windup`); moved into training and anchored on the last command it became an integrator in the balance loop (`slew-anchor-is-an-integrator`); anchored on the measured angle it bounded torque and kept the bandwidth (`beta-anchored-action-target`). The walking lines' safe setting, power-scale 0.8, cut the ends of the recovery policy's full-range travel and left its spikes alone; a gain inside the trained band did the job (`power-derating-cuts-full-range-contract`).
Coach application. Demand the measured pipeline latency/limits in the plant model and in gate conditions; treat every deploy-side derating as a question ("what is this compensating?"); block per-axis command sources that exceed training bands.
doctrine-13DR budget is finite; its distribution is the measured supportRobustness is a conserved budget: disturbance training on an already-hardened lineage borrows from existing margins; DR ranges span the measured deployment support - no fictitious tails (they buy degenerate gaits), no single constants (they allow thin-margin specialization); harden the plant only after the task distribution is final.
Case. The same push dose helped a narrow lineage and damaged a balanced one - budget conservation (`push-dr-conditional-budget-conservation`); wide latency tails bought drag-glide, constant values shipped 60% thinner tilt margins - the answer is a narrow band on the measured support (`dr-tail-plant-continuation`, `constant-value-dr-overfits-margin`); task-first ordering because hardening a soon-to-change task wastes budget (`task-shaping-before-plant-hardening`); COM randomization used deliberately as a behavior-shaping tool, and rolled back on symptom per its own contract (`com-randomization-forces-leg-spread`, `com-dr-rollback-on-symptom`). DR that is switched on can still be thin: the run policy fell in the frontal plane its gain-and-latency randomization never touched (`thin-dr-judged-by-channel-coverage`), and a friction priority settled under one action contract had to be re-measured under the next (`friction-priority-re-measured-after-plant-change`).
Coach application. Before any DR rung: check the untrained policy against the spec, the lineage's current DR load, and the measured real-world range; after it: audit retained margins, not just the new tolerance.
doctrine-14Gates measure what hardware feels: posture, margins, stripped assistsAcceptance batteries carry posture-class rows (tilt max median, per-joint L/R asymmetry, temperature) beside task rows, graded margin columns beside binary gates, chirality scored per side, at least one condition that removes the environment's free stabilization, and validated predictive scalars promoted into the gate.
Case. Three same-shaped judging errors - survival, displacement, wz-difference - all missed what the operator felt; posture metrics had the predictive power (`task-metrics-vs-posture-metrics`, `stand-gate-posture-not-survival`); binary survival saturated and hid a 60% margin gap (`constant-value-dr-overfits-margin`); v5 passed everything on the ground and failed suspended (`suspension-probe-removes-free-stabilizer`); the hip_roll (l+r) scalar predicted real drift direction and ordering and entered the battery (`hip-roll-sum-predicts-lateral-drift`); averages hide chirality (`chirality-scored-separately`); gait-quality gates are judged at speeds that demand a gait (`low-speed-commands-reward-dragging`). The recovery line added the rest of the kit: where failed episodes end, not only where they started (`end-state-confusion-matrix`); a frozen acceptance distribution with a pinned seed (`frozen-acceptance-distribution-and-pinned-seed`); video of the metric rollout itself (`video-as-acceptance-record`); and the admission that a 10 s episode cannot see a stance that fails after a minute (`episode-length-bounds-what-a-gate-sees`). The one-leg line removed a foot-spacing wall that no gate measured, and the feet met on hardware (`removed-wall-returns-on-hardware`).
Coach application. Review every battery for posture rows, margin columns, per-side scoring, and an assist-stripped condition; when operator feel and gates disagree, suspect the metric class first.
doctrine-15Fork and root selection: recoverability, maturity, frozen rewardsChoose fork roots by which candidate's deficits the coming training can pay back (precision is recoverable; lost plasticity, symmetry, and margins are not); prefer mature checkpoints as roots even when younger ones score better as products; never fine-tune through a reward change - continuation is legal only with the reward frozen and plant/DR widening one rung at a time.
Case. s1e-500 beat higher-precision candidates because its exclusive strengths were unrecoverable (`fork-root-recoverable-shortfall`); the b300 arm proved maturity is capital against adaptation shock (`root-maturity-vs-product-quality`); the B-arm scatter/half-recover/collapse signature falsified reward-change fine-tuning and drew the legal boundary for S2 continuation (`fine-tune-reward-change-falsified`).
Coach application. For root debates, build the exclusive-strengths table and ask "which side can be trained back?"; require dual-arm evidence for maturity claims; classify any proposed continuation as reward-frozen or not before approving.
doctrine-16Curricula: verified engagement, lineage counters, disease-phase gatingAutomatic curricula must prove they engage (a saturated ratchet is constant DR wearing a curriculum's name); every ramp counts lineage-cumulative progress, not per-process steps; penalties aimed at late-stage pathologies ramp in after exploration noise decays; difficulty rises on measured per-stratum success, never on schedule.
Case. The s1f ratchet capped at iter 248 and never engaged (`auto-curriculum-engagement-check`); the saturation ramp re-fired at +600 after every resume and no shipped product ever saw the penalty (`curriculum-counter-lineage-steps`); the same penalty worked once gated to the disease phase and became an untouchable mechanism (`gate-penalties-to-the-disease-phase`); record-high aggregate reward hid a fully-failing delay stratum (`aggregate-metrics-mask-subgroup-failure`); bucket share is not a gradient lever (`bucket-share-is-not-a-gradient-lever`). An assist curriculum keyed to a pooled success share was withdrawn on the strength of the categories that already worked (`curriculum-criterion-conditioned-on-lagging-category`); a pace set by per-step income moved only when that income was time-gated (`per-step-income-drives-speed-time-gate`), and the same gate had to be retired in a lineage without the disease (`time-gate-vs-wide-stance-retire-the-fix`).
Coach application. Ask every curriculum three questions: does it engage (show the internal state)? what does it count (process or lineage)? when is it present (against the pathology's phase)? Check where shipped checkpoints sit relative to every ramp.
doctrine-17Probe before training: feasibility first, hypotheses in tablesAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop, enumerate hypotheses in a written table audited against actual configs cheapest-first, race one probe per side of the sim2real boundary for hardware-only pathologies, and use suspended tests to acquit or convict actuators before blaming authority.
Case. "在黑暗里试钥匙" - four sidewalk rungs failed until an open-loop probe separated exploration/waveform/authority in one experiment (`open-loop-probe-before-reward-tuning`); the foot-drag mystery fell to a seven-hypothesis config audit (`hypothesis-table-code-audit`); the period-doubling was resolved by racing a reward-side and a plant-side evidence line - and both paid off, one per sub-case (`period-doubling-evidence-race`); the suspended test acquitted the roll actuator in one measurement (`suspended-test-isolates-actuator-authority`). A read-only configuration probe told a wall from a slope in the recovery line's seated basin (`configuration-probe-wall-not-slope`), and the fix it pointed to - where the feet are - took prone from 0/159 to 158/159 (`prone-dead-end-is-foot-placement`); a knob that did not move its variable was recorded as no test of the idea (`dof-vel-penalty-is-not-a-pacing-knob`).
Coach application. When a skill resists training, prescribe the probe before any further reward edits; require verified target trajectories before imitation terms; keep a falsified-fixes list so closed roads stay closed (`amplitude-cut-falsified-yaw-fix`).
doctrine-18External advice is recomputed locally; values transfer as ratiosEvery external suggestion is classified adopt / already-have / modify / trap by recomputing its claim on the local reward table and probe data; numeric values transfer only as dimensionless ratios (to tracking weight, leg length, sqrt(gL), control rate); citations are verified to exist.
Case. "Start vy very small" would have destroyed sidewalk learning on this reward table - the gradient scales quadratically (`external-advice-audit-against-own-arithmetic`); swing-height targets and weights transferred correctly only through leg-length and tracking-ratio scaling (`transfer-ratios-not-absolutes`); the "6-step delay" was refused for lacking a control rate (`latency-dr-covers-measured-pipeline`); a borrowed reference's structure was FK-verified and its amplitude re-derived from the division of labor (`reference-structure-fk-amplitude-division`); retrieval agents fabricated verbatim arXiv quotes - only source-verifiable material was used; and one dismissed suggestion later proved right for a different mechanism, and was credited (`cycle-average-tracking-for-gait-quantities`). An advisor's staged state machine turned out to exist in none of the three papers it cited, and reading them changed the plan (`advisor-paraphrase-vs-paper`).
Coach application. Intercept every "paper X does Y" with the local recomputation; convert absolutes to ratios before comparison; verify quotes; revisit dismissed advice when new mechanisms appear.
doctrine-19Hardware sessions are scripted experiments, not tuning sessionsReal-robot time executes a pre-registered matrix: risk-ordered (baseline first, fragile last with a spotter), stage-gated (suspended smoke before ground), A/B sessions bracketed by a repeated reference run, operators briefed on measured zero-command and untrained-axis behavior, chirality-aware disturbance protocols, no field tuning - the only legal field changes are scripted, single-variable, and self-reversing.
Case. The S2 acceptance sheet (`risk-ordered-real-deployment`, `battery-bracketed-real-ab`, `know-zero-command-behavior`, `push-test-chirality-protocol`, `no-field-tuning-protocol`); the RAM-only torque experiment with automatic power-cycle rollback (`reversible-single-variable-field-experiments`); and the sim-veto rule - even sim's condemnations get one safeguarded hardware check when they judge the purpose-built configuration (`sim-veto-needs-real-confirmation`). The recovery line's first real run went ahead with its preconditions unmet and was stopped as dangerous (`first-real-get-up-violent-stage-one-policy`); after it: a staged hang, mat and floor protocol (`staged-hang-mat-floor-for-get-up`), a fixed power-cycle pre-flight and two-machine discipline (`power-cycle-preflight`, `two-machine-config-discipline`), a fall guard replaced rather than switched off (`fall-guard-becomes-a-state`), and logs that are part of the run (`hardware-log-is-the-attribution-input`).
Coach application. Turn every hardware request into a runbook with order, gates, brackets, briefing, and anomaly plays; refuse improvised parameter changes on the floor.
doctrine-20Close questions in writing; restart when the debt is structuralAudited questions get frozen verdicts with citable wording and an explicit reopening bar; hardware verdicts are dated by deployment-stack and calibration state and expire when those change; and when successive rungs shuffle symptoms without net progress, freeze the lineage as regression baselines, pay the structural debts, and retrain minimal - carrying laws and instruments, not weights.
Case. The chirality and COM questions were closed with frozen wording and "no reopening without new hard evidence" (`frozen-verdicts-semantic-boundaries`); v5/v6's condemnations expired with the deploy stack (`stale-verdicts-under-old-stack`); a 2-degree calibration fix moved the whole runnable envelope (`zero-offset-calibration-shifts-envelope`); plant upgrades are era boundaries with paired re-baselining (`plant-swap-invariants-vs-shifts`); and the 2026-08-05 reset froze v5-v11, fixed the latency FIFO / manifest / sampling / reward-table debts, and restarted - producing the lineage that reached hardware SOTA (`freeze-lineage-fix-structure-restart`, `minimal-reward-table-with-provenance`). The recovery line's real-robot verdicts ended up in three places that disagree, one of them an undated note in a command file (`write-hardware-verdicts-back`).
Coach application. Maintain the closed-questions ledger and quote it when symptoms recur; stamp verdicts with stack/calibration versions; when a team is three rungs into symptom-shuffling, raise the restart question explicitly with the freeze-fix-restart pattern.
doctrine-21Name the quantity in the space it lives inA goal, reward term or acceptance criterion about the feet, the base or the contact state is computed from the quantity itself - world poses, forces, per-category outcomes - never through a joint-angle, single-signal or pooled stand-in that assumes everything else sits at nominal; and every detector is validated on a behaviour known not to contain the event before it becomes a gate.
Case. The recovery line was caught three times: |ankle roll| as "flat feet" sold stance width and the real robot slid into the splits, a hip-roll criterion was confounded by 50 deg of yaw, and the joint table said 0.271 m where the feet were 0.159 m apart; task-space terms produced the first flat, wide stance (`joint-space-proxy-for-task-space-quantity`). Flight detection lied in both directions across two lines - foot height flagged 40% false flight on a walking gait, contact force alone flagged slip chatter as hops (`contact-detector-single-signal-lies`). A pooled height average described a robot that did not exist - six in ten standing, four in ten sitting (`zero-partial-credit-is-not-an-iteration-problem`) - and the walking line had learned the same lesson on yaw rate (`heading-integral-not-body-rate`).
Coach application. For every reward term and gate row, ask what physical quantity it stands for and whether it is measured directly; flag joint-space or single-signal stand-ins for task-space goals, ask for a detector validated on a negative control, and split pooled metrics by category before reading them.
doctrine-22Continuation needs a live gradient; a release is chosen by a scanContinue a converged policy only on a change that creates a live gradient, on a short budget, with every checkpoint scanned on the transfer axis; choose a release by running the full battery over a band of checkpoints and stop on signals, never by taking the last one; and when edits to the terminal phase cannot move a behaviour, roll back and retrain with the constraint present from the start, keeping the order in which the lineage acquired its mechanisms as explicit curriculum phases.
Case. A continuation with no new gradient drifted MuJoCo transfer from 100/98% to 80/28% while every Isaac gate stayed perfect, and a live-gradient continuation at the same depth kept it (`converged-continuation-is-poison`). One-leg checkpoints 100 iterations apart failed 1 and 38 of 40 cells, and late ones degraded (`checkpoint-choice-is-a-full-gate-scan`). Four in-lineage stance fixes failed because the stance was the end of the get-up path, and from scratch it grew right (`stance-decided-by-get-up-path`); fixes stacked on degraded states were rolled back by the user (`stop-stacking-roll-back-and-audit`); and the lineage's final recipe, trained from scratch in one run, sat at 0% because the order of its curriculum was part of the product (`curriculum-history-is-part-of-the-product`). The omni line's short adaptation budgets and mature roots are the same law seen from the other side (`continuation-budget-not-from-zero`, `root-maturity-vs-product-quality`).
Coach application. Before approving a continuation, ask for the new gradient, the budget and the transfer axis in the scan; before approving a release, ask for the scan; after three rungs without progress on the target, propose rolling back to the last good checkpoint and a from-scratch phase plan instead of a fourth patch.
Experience cards
92 cards matching “joint-space-proxy-for-task-space-quantity”.
Removing a foot-spacing wall passed every simulated gate and made the feet collide on the real robot - nothing priced stance width in the two-foot phase, the policy narrowed to the simulator's self-collision floor, and real calibration offsets closed the last millimetres; the wall came back with a gate
removed-wall-returns-on-hardwareWhen a constraint is removed, name what will govern that quantity instead and add a gate for it; never let a simulator's collision floor be the margin, and when a gate is exceeded by a hair, record the exact numbers and hand the release decision to a person instead of quietly passing it.
Symptom
On the first real-robot try of oneleg_v0 (2026-09-16) the two feet collided; the user also judged the folded foot not high enough.
Context
The V0 reward table had dropped the feet_lateral_distance wall because it seemed to conflict with the hip adduction single support needs. In the two-foot command bucket no remaining term governed stance width, so the policy drifted narrower until the simulator's self-collision stopped it; the sim acceptance had no foot-spacing gate, so 40/40 said nothing about it. On the robot, calibration offsets consumed the margin.
Change
V0.1: the wall restored (-10, minimum 0.16 m), re-checked against measured numbers (a swing-phase lateral spacing of ~148 mm costs 0.12 per step, acceptable); fold weight 0.8 -> 2.0; a ninth gate: minimum foot spacing >= 100 mm and zero leg-contact frames. The removal was kept on record.
Outcome
oneleg_v0_1 (V0r2 model_2200) passed 39/40 with the spacing gate 40/40. The single miss (a 15.4 deg tilt transient against a < 15 deg limit during a side switch, steady 6.9 deg, everything else green) was recorded with its numbers and released for the user to overrule.
Mechanism
An unpriced degree of freedom drifts to wherever the simulator stops it; if that stop is the simulator's own collision model, the policy's margin on hardware is whatever the calibration error leaves.
Applies when
- dropping a reward term that looked redundant or conflicting
- hardware shows a failure no simulated gate measures
- a release candidate misses one gate row by a small amount
“V0 撤墙被真机证伪（2026-09-16）：双脚桶没有任何项管站宽，策略贴 sim 自碰撞底线收窄，真机标定偏差一吃**双脚相碰**。 … min ≥ 100 mm 且腿碰 0 帧（eval_straight 同判据）—— … V0 真机双脚相碰暴露 sim 门未看脚距的缺口 … L s2 标称 tilt 瞬态 15.4°（门限 <15, 超 0.4°, 稳态 6.9°, 该跑其余全绿）——换侧瞬态蹭线, 判定放行留档, 用户可否决。”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §4 feet_lateral_distance 行 / §6 验收门 ⑨ / §8 核查单 7 A policy's gain profile is part of its contract - the one-leg policy needs per-joint gains the default profile lacks, and the manifest refused an evaluation under the default once; the recovery contract's beta was never stamped, a known gap not to repeat
gain-profile-belongs-in-the-stampStamp everything that defines the closed loop a policy was trained in - gains included - into its manifest, and make every consumer refuse a mismatch; a profile field that is not in the stamp is a silent misconfiguration waiting for an operator to forget a flag.
Symptom
A policy trained with hip_roll kp 80 and ankle_roll kp 60 behaves differently, or falls, under the default kp 20/12 profile - and the gain profile is a command-line flag an operator can forget.
Context
The one-leg line added a gain_profile field to the contract so the stamped manifest carries it; the spec's deployment note says the manifest guard blocks rl_default and that it had already bitten once in simulation (an evaluation run without the one-leg profile). The same spec states the general rule - any new profile field must be synced into the manifest builder - and names the counter-example: the recovery line's beta was never put into the manifest. The recovery line itself had decided that its anchored authority is computed from the base rl gains and written into the contract so it cannot drift with the gain flag, and that the older kp x 0.9 profile chosen in the V0 era does not match the beta contract and must not be used.
Change
Gain profile as a contract field checked at load; per-contract gain choices written into the run sheets.
Outcome
Evaluations and hardware runs of the one-leg policy run under rl_oneleg or are refused; the recovery beta gap stayed recorded as known.
Mechanism
A policy is trained against a closed loop whose gains are part of the plant; running it under other gains is an out-of-distribution plant, exactly like a wrong observation scale.
Applies when
- a skill introduces per-joint or skill-specific gains
- deployment gains are chosen by a command-line flag
- adding any new field to a policy profile
“增益档 `--profile rl_oneleg` 必须给 —— manifest 防线会拦 `rl_default`（sim 已咬合一次） … （recovery 的 β 未进 manifest 是已知缺口，不再复制）”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §9b AGX 真机手顺 要点 / §3 契约 Guessed joint friction was 2.5x low and damping 5x high - measure, then DR around nominal
friction-measured-not-guessedMeasure frictionloss and damping separately (they need different rigs), put the measured value at DR center, and express DR as an additive band around that nominal - a DR range around a guessed value can exclude the real robot entirely.
Symptom
Old MJCF friction values were invented, not measured; when finally measured, every guessed value was wrong by a large factor in some direction.
Context
Joint friction split into Coulomb (frictionloss, tau_c) and viscous (damping b). Measured with the robot hung from a crane (吊机测) while armature was measured no-load; the two measurements are deliberately separated. Old MJCF: frictionloss 0.05, damping 0.1, DR joint_friction range [0, 0.1] "凭空拍的" (made up out of thin air).
Change
Replace guessed values with measured ones - frictionloss: RS06 0.15 / RS02 0.12 / RS00 0.13 N*m (old 0.05, i.e. 2.5x too low); damping: 0.02 N*m*s/rad on all three motor types (old 0.1, i.e. 5x too high). DR reshaped from an absolute made-up range [0, 0.1] to an additive band around measured nominal: joint_friction_add [-0.05, +0.10].
Outcome
"摩擦定稿(与 armature 一起, plant 参数第一次全部来自实测)" - friction frozen as part of the first fully-measured plant; DR now brackets a measured truth instead of spanning an invented interval.
Mechanism
Coulomb friction and viscous damping have opposite behavioral signatures (constant-torque threshold vs velocity-proportional drag); guessing both wrong in opposite directions gives a plant that is simultaneously too easy to start moving and too hard to move fast. DR centered on a wrong nominal makes the policy robust to a family of plants that does not contain the real one.
Applies when
- plant friction/damping values have no measurement provenance
- DR ranges are absolute intervals rather than bands around a nominal
- policy is over- or under-damped on hardware relative to sim
“测关节摩擦。吊机测，而armature应该空机测试。… frictionloss τ_c (N·m) │ 0.15 │ 0.12 │ 0.13 │ 0.05(低 2.5×) … damping b (N·m·s/rad) │ 0.02 │ 0.02 │ 0.02 │ 0.1(高 5×) … DR │ joint_friction_add: [−0.05, +0.10] 叠标称 │ 旧 [0, 0.1] 凭空拍的”
Experience.md § 摩擦定稿表 (lines 12-25) The standing-pose reward had been pulling toward the narrow stance the whole line was fighting - a zero-training kinematic audit of the target vector found it, after first auditing the wrong nominal
pose-target-geometric-auditBefore training on a pose target, audit it with forward kinematics - is it geometrically consistent (feet flat, intended stance, intended width) and is it the frame you think it is (action nominal vs standing default)? A posture term's target may itself be the attractor you are fighting.
Symptom
Several rungs aimed at widening the stance failed; the stance stayed narrow as if something kept pulling it back.
Context
The audit (MuJoCo forward kinematics, no training): every 5 deg of hip roll widens the stance ~5.5 cm (0.271 m at 5 deg, 0.383 m at 15 deg); at 47 deg of hip yaw a wide stance cannot be flat-footed (residual foot tilt ~0.7 x hip roll), which explained the stalled rungs. The first report also said the stand_pose nominal (hip roll 25, knee 60) has a 63 deg residual foot tilt - but that was the action frame's nominal (the limit-midpoint squat), which stand_pose never used, despite a docstring warning not to mix them. stand_pose's real target was DEFAULT_JOINT_POS: the contract's all-zero pose, legs parallel, ~0.22 m apart.
Change
The disease statement was corrected in writing: the narrow stance was not an accidental by-product of proxy traps but the target stand_pose had been actively rewarding. A stored "narrow the stance" knife was marked toxic. V2.8 moved the target to a flat 15-deg stance (sigma 3 -> 1.5, flat_feet margin 5 -> 20 deg).
Outcome
V2.8 still failed in-lineage (stance unchanged, feet nearly overlapping, mu 0.4 transfer 2%) - see stance-decided-by-get-up-path - and the from-scratch V3.1 removed both roll joints from stand_pose and put width into a task-space term, which is what finally produced a 0.355 m flat stance. The 63 deg finding was kept as a warning: an action nominal used as a standing target would be a ready-made pit.
Mechanism
A posture term with a sharp kernel around the wrong target is an active attractor; every other term fighting it pays twice.
Applies when
- a posture keeps returning despite penalties against it
- a reward uses a default or nominal pose as its target
- the contract has more than one "nominal" (action frame vs standing pose)
“上文"stand_pose 的 nominal (hip25/knee60) 残倾 63°"**审计错了对象**:那是 **动作参考系 nominal**(限位中点蹲),stand_pose 从未指向它(函数 docstring 原文即警告"两者别混",还是混了 —— 记档)。 … **修正后的病根陈述:窄站距不是代理陷阱的意外副产物,而是 stand_pose 一直在主动奖励的目标本身**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §44 勘误(实现时抓到):审计混了两个 nominal —— 真病根比误诊的更直白 Gate a new reward term by its command so all old modes score pointwise identical
gate-new-reward-terms-by-commandWhen a reward term must be added mid-lineage, gate it on the condition that defines the new task so every pre-existing situation scores exactly as before - and still watch for value-rescale pathologies inside the new mode.
Symptom
Adding a lateral tracking reward (track_lin_vel_y_exp) ungated would have paid 0-2.0 per step even in modes with cmd_vy = 0 (healthy gait sway of vy ~0.1 already earns 1.28), shifting the whole reward table by a large bias and rescaling the value function - no longer "just adding one mode".
Context
C4 was the C ladder's only true reward surgery. Single-variable discipline required that the change be invisible to every existing mode. The chosen construction: gate_by_cmd=True - the term pays only when |cmd_vy| > 0.02, so for all modes with cmd_vy == 0 the term is pointwise zero, i.e. the reward is pointwise identical to before the change. The same trick appeared earlier in C1: replacing the vy L2 tax with a command-error version that is "对 cmd_vy≡0 逐点同值" (pointwise equal when cmd_vy is 0), explicitly classified as not-a-reward-change.
Change
track_lin_vel_y_exp added with gate_by_cmd=True (weight +2.0, std 0.15); the residual acknowledged honestly - inside the side bucket the values DO change, so the rung still watched the known reward-reshuffle pathology signature (s1c B-arm: scatter -> half-recover -> collapse) as a stop criterion.
Outcome
Old modes provably unaffected (pointwise-equal argument); attribution for any change in old-skill metrics stayed clean through the C4 redo series.
Mechanism
PPO's critic normalizes to the reward scale it sees; an ungated additive term shifts returns in every state and re-scales advantages globally, entangling the new skill with all old ones. Command-gating confines the new term's support to the new mode's state distribution, making "pointwise identical elsewhere" a provable property rather than a hope.
Applies when
- adding a tracking/shaping term for a new command or skill to a lineage that must not regress
- reward change proposed while other skills are still being gated
- reviewing whether a config diff counts as a reward change
“只在 |cmd_vy| > 0.02 时付。不门控的话它对 cmd_vy≡0 的老模式也给 0~2.0 分（健康摇摆 vy≈0.1 → 1.28），等于给整张奖励表加一个大偏置、值函数尺度全变 … 门控后老模式逐点得 0 = 与加项前逐点同值，单变量纪律成立。… 但 side 桶内的值确实变了 —— 这仍是奖励表改版，开级盯 s1c B 臂签名”
train/C_LADDER_RUN.md § 3d. gate_by_cmd=True（重要） Design the next run to complete the 2x2 - either outcome then convicts or acquits a factor cleanly
fill-the-missing-factorial-cellWhen two config factors are jointly suspected, lay out the factorial of existing evidence, spend one run on the missing cell with both interpretations and an early-abort tripwire written in advance - and treat either outcome as a verdict, not a disappointment.
Symptom
Hip joints froze at the action clamp in v7, but the history could not say whether the culprit was the raised action_rate (-0.2) or the halved reference amplitude (scale 0.15): existing versions covered only three corners of the (rate x scale) space - v5 (-0.03, 0.30) healthy, v6 (-0.03, 0.15) healthy, v7 (-0.2, 0.15) frozen.
Context
v9 was designed explicitly as the missing cell (-0.2, 0.30), with the readings pre-registered: v9 not frozen -> the real anti-freeze force was always the reference amplitude and -0.2 may stay; v9 frozen -> -0.2 is convicted beyond appeal (freezes at both amplitudes) and the next version goes straight to a structural fix. "两个结局都是干净的信息" - both endings are clean information.
Change
One training run allocated purely to complete the factorial, with freeze tripwires (joint_pos_ref telemetry <0.1 at iter 1000-1500 -> abort, do not run to 6000) so a conviction costs the minimum compute.
Outcome
v9 froze - the rate weight was convicted at both amplitudes ("−0.2 铁案定罪"), and v10 moved to the structural saturation fix with the weight question closed instead of re-litigated.
Mechanism
Three corners of a 2x2 leave the two factors confounded in the failure corner; the fourth observation makes each factor's marginal effect identifiable. Pre-registering both readings turns the run into a guaranteed-informative experiment regardless of outcome.
Applies when
- two config changes are confounded in a failure
- version history already covers some corners of a factor grid
- deciding what single experiment buys the most attribution
“这恰好补齐一个 2×2 实验矩阵的缺格 … v9 不冻 → 真正的抗冻结主力一直是参考摆幅,−0.2 可以留;v9 仍冻 → −0.2 铁案定罪(两种摆幅下都冻),v10 直接上结构修复 … 两个结局都是干净的信息。”
train/WALK_V9_SPEC.md § 0. 设计原则 (2×2 实验矩阵) A hardware run without its log is an anecdote - the first real get-up's policy, gain profile and log were never recorded, two CSVs stayed "to be reported", and runbook commands wrote different policies' logs under one copied filename
hardware-log-is-the-attribution-inputMake the log part of the run: name it from the policy and conditions automatically (never by hand-copied filenames), record the policy digest and gain profile inside it, include what the open questions need (torque, joint positions and targets), and treat a session without a collected log as incomplete.
Symptom
The recovery line's oldest open question - whether Isaac or MuJoCo reads torque demand correctly - was waiting on real-robot logs that never arrived, and the verdicts that did arrive could not be tied to files.
Context
deploy_policy writes a CSV per run (--log); the runbook's own analysis snippet reads its joint-position, target and action columns (q_, tgt_, act_), and the recovery hanging checklist asks for torque and joint logs for the whole run, to be compared with simulation. The first real get-up (08-09): policy, gain profile and log "to be recorded later". The first real A/B (08-11): v2_5b's result and both policies' CSVs "to be reported". In the runbook's walking commands, three runs of two different c4 policies log to real_s1e_pw08_teleop_0808.csv, and s1e and s2e_fric runs log to real_c2_700_pw08_teleop_0808.csv - filenames copied from other commands.
Change
None recorded; the spec kept listing the open-loop comparison as waiting for real logs.
Outcome
No real-robot log appears in the recovery spec through §50, so the simulator disagreement stayed unresolved and hardware verdicts stayed unattached to data.
Mechanism
Attribution needs the run's identity (policy digest, profile, conditions) and its signals in one artifact; a filename copied from another command mislabels the file, and a log not collected at the session is rarely collected later.
Applies when
- planning a hardware session whose result should settle a sim question
- log filenames are typed or pasted by hand
- hardware feedback arrives as prose without files
“python tools/deploy_policy.py --policy train/policies/omni_c4_ff800_pj.onnx … --log train/real_logs/real_s1e_pw08_teleop_0808.csv … q,t,a=d[:,c("q_")],d[:,c("tgt_")],d[:,c("act_")]”
RL系统/FOLLOW THIS copy 2.md § Walk 遥控 / S2 / csv 分析片段 (operator runbook, undated) The hip_roll (l+r) asymmetry scalar predicted real-robot lateral drift - promote validated sim scalars into the gate
hip-roll-sum-predicts-lateral-driftHunt for cheap sim scalars that predict real-robot behaviors, validate them on direction AND ordering across multiple policies, then promote them into the acceptance battery; treat later violations as debt to justify in writing, not noise to ignore.
Symptom
A persistent hip_roll left/right asymmetry row in the sim2sim symmetry table had been dismissed as "calibration or mechanical asymmetry" noise; meanwhile real deployments drifted sideways by policy-dependent amounts.
Context
Forward-kinematics analysis reframed the scalar: both hip_rolls move the feet in +y for positive angle, so a same-signed (l+r) sum IS a lateral translation mode - the scalar is a direct lateral-drift bias estimate. Checked against real deployments: s1e (l+r = -0.0178, smallest magnitude) was the steadiest with least drift; 700 (+0.0253) drifted mildly left; A800 (+0.0267) drifted clearly left with the largest tilt 12.9 deg. Direction correct 3/3, ordering correct 3/3 (the log's heading calls it "四枚四中", four-for-four).
Change
The scalar was promoted into the acceptance battery as a posture-class criterion alongside tilt-max median: "hip_roll 左右不对称 |l+r| 不得比父代大" - doubling as a heat proxy (error ~ torque ~ heating).
Outcome
Used at every later gate; when the C4 product exceeded it by +0.005 rad (~+0.3 deg vs parent), the criterion was not silently waived - it was booked as explicit debt with a mechanism argument (the increment is task-required, far smaller than the sidewalk amplitude +/-2.2 deg) plus a related account (stand saturation 32.4% -> 37.2%).
Mechanism
A policy's static joint-angle bias in a translation-producing mode integrates into real-world drift; sim can measure that bias precisely and cheaply. A sim scalar earns gate status exactly when its predictions are validated against hardware in both direction and ordering - and a validated gate may only be exceeded with a written mechanism-level justification, never silently.
Conflicts
The log's heading says "四枚四中" (4/4) but the evidence table lists three policies and the text says "方向 3/3、排序 3/3"; the fourth instance is not shown in this file.
Applies when
- a real robot drifts or leans in a policy-dependent way
- deciding which sim measurements deserve gate status
- a validated gate criterion is marginally exceeded by a new product
“s1e | −0.0178（绝对值最小）| 微右、最不飘 | 三者中最稳、飘最小 ✓ … A800 | +0.0267 | 左、最飘 | 明显左飘、倾角最大 12.9° ✓ 方向 3/3、排序 3/3。 → 正式纳入验收表（与「倾角 max 中位」并列为姿态类判据）。”
train/C_LADDER_RUN.md § 3e. 顺带：hip_roll 左右不对称 (l+r) 就是横移偏置 —— 四枚四中 Raising a command bucket's share does not strengthen its per-state gradient - it only starves the other modes
bucket-share-is-not-a-gradient-leverWhen a skill is not learning, first prove its per-state signal is nonzero (ignore-floor and probe checks); only rebalance sampling shares to fix genuine sample starvation, and account the regression risk to the diluted modes before doing it.
Symptom
Sidewalk was not learning, and the reflex proposal was to give the side bucket a larger share of sampled commands.
Context
The C4-redo3 rung explicitly kept the 20/40/20/20 bucket (stand/forward/turn/side) with the reasoning written out: PPO computes advantages per state, so bucket proportion does not change the per-state gradient of side states; at 4096 envs x 20% x 24 steps the rollout already contained ~19.7k sidewalk states - sample count was not the bottleneck. And the cost side was already measured: cutting forward from 60% to 40% had made vx+0.30 die at +400 in an earlier run - more cuts would only collapse it sooner.
Change
Bucket proportions held constant across the entire C4 redo series; the actual bottlenecks (metric frame bug, reward variance penalty, exploration form) were pursued instead.
Outcome
Sidewalk was eventually fixed with zero bucket changes (feed-forward delivery, +100 iters); forward/turn skills never suffered starvation-induced regressions during the redo series.
Mechanism
Policy-gradient credit is assigned per visited state; oversampling a mode multiplies its states in the batch but not the informativeness of each, so if the per-state gradient is ~0 (behavior unreachable or reward indifferent), N times zero is still zero - while the displaced modes genuinely lose data and regress.
Applies when
- proposing to oversample a failing task/command mode
- a majority mode regresses after share rebalancing
- budgeting env count vs mode share for a multi-skill policy
“比例不动：PPO 逐状态算优势，桶占比不改变单状态梯度；4096 env × 20% × 24 = 每 rollout 已有 1.97 万个侧走状态，样本数不是瓶颈；而 forward 60%→40% 已实测让 f30 在 +400 处死掉，再加码只会更早塌。”
train/C_LADDER_RUN.md § 3i. 桶 20/40/20/20 不动（比例不动） A pull-assist curriculum keyed to a global success share was satisfied by the categories that already worked and withdrew before prone learned anything - conditioning the criterion on prone took it from 2.5% to 98.7%
curriculum-criterion-conditioned-on-lagging-categoryMeasure a curriculum's advancement criterion on the population the scaffold is meant to help; a global success share is met by whatever already works, and the help is withdrawn before the lagging case learns.
Symptom
Under the beta-anchored action, supine and side stood reliably while prone still sat (1.3%). A pull-assist curriculum added to help it was withdrawn completely within ~790 iterations and prone moved only to 2.5% (noise).
Context
The pull assist follows HoST: an upward force on the base, active only when the torso is within 30 deg of vertical, scaled by body weight (HoST's 200 N on G1 = 0.583 BW -> 56 N here, steps of 5.6 N, ten levels to zero); the product must pass with no assist. It had already taught sit-to-stand in V1. In V2.1 its advancement criterion was the standing-time share over all envs (threshold raised to 0.55 because the share was already ~0.53).
Change
V2.2: PullAssistForce with gate_category = "prone" - only envs whose first step classifies them as prone count toward the criterion - and the threshold back at 0.35. A feasibility signal was pre-registered: if prone's share stayed near zero under the full 56 N, return to the roll-over path instead of adding force.
Outcome
The prone-conditioned curriculum withdrew level by level only as prone itself passed: prone 98.7%, and the four-category gate passed for the first time on the line (98.6% overall, re-falls 0%, torque gate PASS).
Mechanism
A pooled success share is filled by the categories that already succeed (supine/side ~53%), so the scaffold is removed on their account before the lagging category has used it.
Applies when
- an assist, guide force or easier setting is withdrawn by a success threshold
- one task category lags while the pooled metric looks healthy
- a curriculum ran to completion without changing the lagging category
“**教训:全局站立占比阈会被存量类别(supine/side ~53%)凑够,拉力在 prone 学会前就撤光了 —— metric 设计失误,不是拉力机制失效**(它在 V1 教会过 坐→站)。 … **V2.2(已启动)**:`PullAssistForce` 加 `gate_category="prone"` —— 达标判据 只统计 prone 类 env”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §34 V2.1 判决(2026-08-10) The fallen-state reset was designed, not sampled from SO(3) - fixed category shares with jitter, a low drop that settles physically, equal left/right shares for mirror augmentation, and a numeric check before training
fallen-pose-reset-distributionBuild a fallen-start distribution from named, physically plausible categories with jitter and a settle phase, keep mirrored categories at equal probability, and check the realized shares and penetration numerically before spending a training run on it.
Symptom
A get-up policy can only learn from the fallen states its resets produce; uniformly random orientations produce ground-penetrating and limit-jammed states the robot can never be in.
Context
R0 reset_root_fallen: supine 30%, prone 30%, side_l 15%, side_r 15%, mid (random axis 50-125 deg) 10%, +/-15 deg jitter, full yaw, dropped from 0.28-0.40 m and left to settle under physics, joints uniform inside the soft limits with a 5% margin plus small random velocities. Random SO(3) was rejected (the advisor agreed). side_l and side_r must have equal probability because mirror augmentation turns a left fall into a right fall. The advisor had proposed supine and prone only for R0; the spec included side and mid because the feasibility accounts showed physical solutions for all of them, and wrote "narrow back to supine+prone" down as the first fallback. With no display on the training box the reset was checked numerically instead of by eye.
Change
Category mix as above; realized shares, settle height and penetration measured over 512 envs before the first run. A fallen-state bank (real falls, settled and stored) was pre-registered for R2.
Outcome
Realized shares 29.3/31.6/16.4/17.8% against the config, settle +0.262 m, final penetration 0/512 (a 0.10 m peak at the write instant, ankle links only, pushed out within 80 ms because the 0.28 m drop floor is shorter than a fully extended leg). R0's failure was a reward basin, not a reset artifact. The fallen-state bank stayed unbuilt through V3.1 (checklist item open); R0.3 later re-sliced the prone share into roll_l/roll_r bands, which is what forced the acceptance distribution to be frozen separately.
Mechanism
A category-structured, physically settled start distribution keeps training on states the robot can actually occupy, and equal mirrored shares keep mirror augmentation a pure doubling of data rather than a bias.
Applies when
- designing reset distributions for get-up, recovery or multi-contact skills
- mirror/symmetry augmentation is on and the task has chiral start states
- no viewport is available to inspect resets on the training machine
“角度 jitter ±15°、yaw 全域、0.28~0.40 m 低空放下由物理沉降,关节软限位内 均匀(留 5% 余量)+ 小随机速度。**不用 random SO(3)**(会采出穿地/极限卡死 等现实不可能状态,顾问同判) … side_l/side_r **概率必须相等**(镜像增强的样本同分布前提)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §3 R0 任务定义 / §9 核查单 Choose the fork root by which candidate's shortfalls are recoverable, not by headline score
fork-root-recoverable-shortfallWhen picking a checkpoint to fork from, rank candidates by whether their weaknesses are trainable-back, not by current headline metrics; prefer the candidate whose deficits the upcoming training directly pays for.
Symptom
Multiple candidate checkpoints for the omni-command ladder root, each best at something different: fric-3000 had the best tracking precision (vx 88-91%) and hardened plant robustness; s1e-500 had lower precision (vx 82%) but was the only candidate that could still walk backward.
Context
Root selection ran as a data probe, not a preference vote: 6 candidates x 8 out-of-distribution omni commands x 20 seeds = 960 cells (probe_omni_0808.json). s1e-500 @pw1.0 survived 20/20 in all eight conditions including backward at 67% tracking; the deep-trained fric lineage scored backward 0-3/20 despite better forward precision.
Change
Decision criterion made explicit: list what each candidate exclusively wins at, then ask which of those wins the loser could train back. fric-3000's exclusive wins (precision, plant robustness) are both retrainable - precision is directly optimized by the reward, plant hardening is a planned later pass. s1e-500's exclusive wins (backward plasticity 20/20 vs 2/20, disturbance margin 159/160 vs 125/160, push chirality symmetry 40/40 vs 17/40) had all been shown unrecoverable - push-level rungs failed twice, chirality never recovered even with mirror augmentation on. Root = s1e-500.
Outcome
s1e-500 carried the whole C ladder; its backward skill was preserved through C2/C4 gates (regress budget <=2/20 enforced), and the final C4 product passed a 260-cell battery at 20/20 everywhere.
Mechanism
Training can re-earn anything the objective directly pays for, but capabilities that earlier training destroyed and never restored (plasticity, symmetry, robustness margins) are empirically one-way doors. The information-bearing comparison is therefore recoverability of each candidate's deficit, which the team stated as "独占项的可恢复性正好相反 —— 这就是判据" (the exclusive items' recoverability is exactly opposite - that is the criterion).
Applies when
- selecting a resume/fork root among several checkpoints
- one candidate is more precise but another retains a skill the rest lost
- planning a task-extension ladder from an existing lineage
“fric-3000 赢在精度（vx 88~91%…）与 plant 鲁棒性 → 两样都训得回来…；s1e-500 赢在可塑性（C1 20/20 vs 2/20）、抗扰余量（159/160 vs 125/160）、手性对称（推 ±6 N·s 40/40 vs 17/40）→ 三样都训不回来 … 独占项的可恢复性正好相反 —— 这就是判据。”
train/C_LADDER_RUN.md § 0. 为什么根是 s1e-500（数据，不是偏好） The restart reward table lists a reason for every term AND a lesson for every exclusion - absent terms are removed, not zero-weighted
minimal-reward-table-with-provenanceMaintain the reward table as an evidence ledger: every term cites the episode that justifies it, every excluded term cites the episode that convicted it (including the development stage it is valid at), and retired terms are deleted from the config, never left at weight zero.
Symptom
Seven walk generations had accumulated an entangled reward table where nobody could say which term earned its place; the restart needed a table that could be audited line by line.
Context
The minimal table v2 was built under three written principles: "一项管 一件事、结构性反抬脚的项一个不留、塑形只留一套相位逻辑;不在表里的一律 不加" (one term per job; zero structurally-anti-lift terms; exactly one phase-shaping logic; nothing outside the table gets added). Every row carries its provenance (e.g. base_height target = standing height cites the v4 crouch lesson; split x/y tracking cites the merged-exp gradient hole; world-frame yaw cites the v1/v3 body-frame lesson). Every EXCLUSION carries its same-type precedent: feet_landing_vel out because it is poison while the gait is unformed (drag pays 0, lifting pays - the v4-clearance / v8a-B "reverse threshold" family) though it was fine in v7 when the gait already existed - term validity depends on developmental stage; feet_air_time out with its measured non-lever evidence (v6 had it at 2.0 and still lifted 4 mm); and replaced terms are REMOVED from the config ("置 None,不是权重 0 挂着") so audits see truth, not dormant weight.
Change
Reward table rebuilt as ~20 rows each with weight + provenance column; exclusion list maintained alongside with the falsifying episode for each; dormant terms deleted rather than zeroed.
Outcome
Later revisions (S1.2/S1.3) modified the table by citing and updating specific rows' evidence rather than re-arguing the whole design; the table doubled as the lineage's reward-lesson index.
Mechanism
A reward table is a set of standing hypotheses; attaching each row's evidence makes revisions targeted and reversible, and recording why a term is absent prevents the cycle of re-adding known poisons. Deleting vs zero-weighting matters because config audits and DR interactions see the term either way - a zero-weight term is dormant complexity waiting to be flipped on wrongly.
Applies when
- designing a reward table for a restart or new task
- someone proposes re-adding a previously removed term
- auditing which reward rows still earn their place
“原则:一项管一件事、结构性反抬脚的项一个不留、塑形只留一套相位逻辑;不在表里的一律不加 … feet_landing_vel(评审 #4):拖地时代价恒 0、抬脚才收费——与 v4-clearance/v8a-B 同属「反抬脚门槛」家族,步态未成形时是毒;v7④ 加它时步态已存在。… 已从 cfg 移除(置 None),不是权重 0 挂着。”
train/OMNI_V0_SPEC.md § 3. 最小奖励表 v2 / 明确不带 Before adding a command mode, compute what ignoring it costs - the lazy optimum must lose
reward-cost-of-ignoring-auditPrice the do-nothing policy for every new command or objective: compute reward-per-step for "comply" vs "ignore" from the actual table, and only train once ignoring is decisively unprofitable.
Symptom
A new command mode can be silently unlearnable if the reward table makes "ignore the command entirely" nearly free compared to the tracking reward available elsewhere.
Context
For each C rung the team computed the per-step cost of completely ignoring the new command versus ignoring forward: ignoring vx=0.25 costs 1.264/step; ignoring wz=0.20 costs 0.984/step (78% of forward - gradient sufficient, so C2 was certified "zero reward surgery"); but ignoring vy=0.10 cost only 0.020/step - 50-60x weaker, because vy entered the table only as an L2 tax, not a tracking term.
Change
Rule instituted: a rung may claim "no reward change needed" only after this arithmetic shows the ignore-cost is the same order as forward's. For C4 the audit failed, so track_lin_vel_y_exp (+2.0, std 0.15, same form as vx) was added - raising the ignore-cost at cmd_vy=0.10 from 0.020 to 0.718/step (36x).
Outcome
C1/C2/C3 proceeded with zero reward edits, keeping single-variable attribution clean; C4's needed surgery was identified before training instead of after a failed run.
Mechanism
PPO converges to whatever costs least; if the reward margin for obeying a new command is a rounding error against existing terms, the "ignore" policy is the optimum and no amount of training fixes it. The audit prices the lazy optimum explicitly before spending compute.
Applies when
- adding a command axis or task mode to an existing reward table
- a new skill trains flat while other skills stay healthy
- certifying a rung as "no reward change"
“cmd wz 0.20 → 0.984（coarse .473 + fine .491 + L2 .020）… 对照：忽略 vx=0.25 = 1.264（本级 78%，同量级）；忽略 vy=0.10 = 0.020（弱 50 倍——那才是 C4 必须加 track_lin_vel_y_exp 的原因）。本级不动奖励表。”
train/C_LADDER_RUN.md § 4. 原地转级（C2）② 奖励梯度已验够 A get-up policy righted itself and sat - three terms paid the seated pose 84% of the return, and the only shaping term that could tell sitting from standing was an exp kernel outputting 5e-5
seated-basin-dead-exp-kernelWhen a policy parks in a degenerate posture, tabulate what each reward term pays that posture against the target (watch contact terms that reward touching rather than bearing load) and evaluate every exp kernel at the error actually observed; a kernel narrower than the real error is switched off, and widening it is a one-variable repair that adds nothing new.
Symptom
R0 converged by iteration 700 and gained 1.7% over the next 2,300; success 0.0% in all four fall categories. Three of four success conditions passed (tilt median 1.0 deg, both feet in contact 99.6%, angular rate low); height passed 0.6% (median 0.204 m against 0.326). The robot knelt in a W-sit: hip yaw +/-47 deg, knees folded to 92% of the hard limit, shins flat, pelvis on the ground, torso vertical.
Context
Minimal reward table: upright (1-g_z)/2 +2.0, base_height linear progress +1.5, stand_pose exp(-||q-q_stand||^2/std^2) x upright gate +1.0 with std 1.0, still +0.5 and feet_on_ground +0.5 both x the upright gate, plus regularizers. The upright gate is a hinge that opens below 30 deg of tilt. The pre-registered fallbacks were then checked against the measured state: tightening the tilt gate was falsified (tilt was already 1.0 deg); a success bonus contradicted the spec's own no-cliff-bounty rule; narrowing the categories was useless (all four converged to the same pose); raising init noise was too weak for a basin this deep. Only a half-rise intermediate state addressed it, and a cheaper repair existed.
Change
R0.1 (user decision, single variable): stand_pose std 1.0 -> 3.0. Not a new term and not a bounty - repairing a declared term that was numerically dead. The two runs' logged env.yaml differ in log_dir and std only.
Outcome
R0.1 58.2% overall (R0 0.0%): supine 91.5%, side 82.2%, mid 55.9%, prone 0/156; knees fully straight; ||q-q_stand||^2 9.99 -> 0.91 and the stand_pose term 4.6e-5 -> 0.90; get-up ~1 s, no re-falls, the curve still rising at the 3,000-iteration cap. Prone stayed at zero and needed a different fix (see prone-dead-end-is-foot-placement).
Mechanism
Sitting earned upright 1.98/2.0, still 0.43/0.5 and feet_on_ground 0.46/0.5 - 3.0 of a 3.57 per-second return - because feet_on_ground asked for contact, not load. The only terms separating sitting from standing were base_height (+0.70/s for standing) and stand_pose, whose kernel at the real 9.99 rad^2 error (75% of it in the two knees) was exp(-9.99) = 4.6e-5 with a gradient near 1e-4. Standing up meant risking 3.0/s to gain 0.70/s while unfolding knees at 92% of their limit under load. With std 3 the same term is exp(-9.99/9) = 0.33 - a live gradient, three quarters of it on the folded knees.
Applies when
- a policy converges early to an upright but low, seated or kneeling pose
- a posture-matching exp term reads ~0 in the training logs
- contact-based rewards saturate while the task metric does not move
“**关键:`feet_on_ground` 只问"触地"不问"承重", 跪坐时双脚确实贴地,照样满分。** 三项 3.0/s = 总回报 3.57/s 的 84%。 … **exp(−9.99) = 4.6e-5** —— 权重 1.0 的项实际输出 5e-5、梯度 ~1e-4, **不是"还没学会",是数值上根本不存在**。 … **R0.1 决定(用户 2026-08-09 定,单变量)**:`stand_pose` 的 `std` **1.0 → 3.0**。 不是加新奖励、不是悬崖悬赏,而是**修复一个已声明但数值失效的项**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §11 R0 首跑(recovery_r0, 2026-08-09):FAIL —— 翻正了但坐着 Add a termination that makes the degenerate strategy fatal - no height cut-off meant crouch-shuffling could live forever
termination-closes-degenerate-basinFor each known degenerate strategy, check whether the termination set makes it fatal; if the robot can live indefinitely inside the degenerate posture, add a termination just past the intended operating envelope rather than escalating penalties.
Symptom
Crouched foot-dragging survived indefinitely because the termination set contained only bad_orientation (40 deg) and base contact - there was no height termination at all, so a deep squat was a viable long-term strategy.
Context
The hypothesis audit found the missing termination (hypothesis 7); the cross-check against published configs found the field practice: Booster terminates at 0.45 m (38% of body height) and the research warning is that the termination height must not be so low that crouching survives it. The proposed value: 0.32 m, just below the walk crouch base height 0.3739 - a deep squat terminates immediately, "断掉蹲着蹭的活路" (cutting off the crouch-shuffle's livelihood).
Change
Add height termination at 0.32 m as a second-priority item of the walk fix package, alongside restoring base_height_l2 to -10.
Outcome
Entered the v5/v6 fix package under which the crouch-shuffle optimum disappeared (34 mm clearance, 87% tracking by v6).
Mechanism
Termination conditions define which strategies exist at all: a reward penalty prices a behavior, but a termination deletes its future returns entirely. Degenerate basins that are merely penalized can remain optimal under enough tracking pressure; a termination placed between the degenerate posture and the intended one makes the basin unreachable as a steady state.
Applies when
- a degenerate but stable behavior persists across reward tunings
- auditing termination conditions for a locomotion task
- a policy exploits the gap between penalized and terminated states
“加终止高度:研究第 6 条"终止高度不能低到让蹲着也能活"。我们完全没有高度终止。建议 0.32 m(略低于 walk 蹲姿基座高 0.3739,深蹲即终止)。… 加终止高度 0.32 m(深蹲即终止,断掉蹲着蹭的活路)”
train/WALK_DIAGNOSIS.md § 修正 ④ / 最终改动清单 第二优先 FK-verify a borrowed reference's structure, then size its amplitude by the reference's job - it pins phase, the policy adds lift
reference-structure-fk-amplitude-divisionWhen borrowing a reference trajectory: verify its structural claim against your own kinematics (an invariant like flat-foot), assign it the phase-pinning job, and size amplitude low enough that the policy contributes the lift - moving toward a proven foreign value in halves, not jumps.
Symptom
walk_v4 had big knee swing (40-46 deg) but only 18-24 mm foot lift - amplitude without hip/knee/ankle phase coordination; later, walk_v5's real-robot swing ballooned to 73.6 deg (sim 55.7) with violent footfalls - amplitude over-driven by the reference.
Context
Structure first: Humanoid-Gym's 1:2:1 hip:knee:ankle reference was verified on the local model before adoption - the ratio exactly satisfies the locally derived flat-foot constraint hip - knee + ankle = 0, FK-tested at multiple amplitudes with sole pitch 0.00 deg throughout. Amplitude second, and here the first reasoning failed honestly: FK said shorter legs need LARGER reference scale (0.30 for 30 mm lift), and the FK was correct - but the premise was wrong ("FK 没错, 但前提错了"): it assumed foot lift must come from the reference. HighTorque Pi, same scale, uses 0.08 with a 0.02 m foot-height target - proof that lift is added by the policy ON TOP of the reference, whose actual job is pinning the phase relationship. Scale 0.30 made the reference the entire gait: over-constrained and over-driven. The correction went to 0.15, deliberately not Pi's 0.08: "一次只走一半, 留退路" (walk half the distance, keep a retreat).
Change
target_joint_pos_scale 0.30 -> 0.15 as one of v6-minimal's three changes, treating both the footfall force and the lateral kicking (yaw momentum scales with leg swing amplitude).
Outcome
v6 improved landing force 1.72x -> 1.55x, suspended tilt 45.9 -> 23.0 deg, turn-gain asymmetry 70% -> 19%; the later v6-halved-shaping experiment (35 mm -> 4 mm collapse) confirmed the reference still carries the gait's existence on this machine - the division of labor is real but machine-specific.
Mechanism
A joint-space reference plays two separable roles: encoding structure (phase relations that keep the foot flat) and injecting amplitude (energy). Structure transfers across robots and is checkable by FK against an invariant; amplitude is a negotiation with the policy, and over-assigning it to the reference removes the policy's freedom to modulate lift with state.
Applies when
- importing a reference gait / imitation target from another codebase
- reference amplitude reasoning based on leg length alone
- real swing amplitude far exceeds sim's under a strong reference
“FK 没错, 但前提错了。我默认抬脚必须由参考轨迹产生。HighTorque Pi 同尺度机器人 … 用 0.08, 而它 target_feet_height = 0.02 m —— 说明抬脚是策略在参考之上加出来的, 参考只负责钉住髋/膝/踝的相位配合。我们取 0.30 等于让参考本身就是整个步态, 过约束 + 过驱动”
train/WALK_V6_MINIMAL.md § ① target_joint_pos_scale 0.30 → 0.15 Write each config's expected hardware signature before the session - and if reality disagrees, change the books, not the conclusion
preregistered-real-expectationsBefore hardware runs, write per-config expected signatures and the disagreement rule (hardware outranks sim; discrepancies get recorded, not reconciled); validate the harness by checking it reproduces at least one known real behavior.
Symptom
Hardware impressions are easily narrated after the fact; without written expectations, any real-robot outcome can be made to "match" the sim story.
Context
The S2 acceptance sheet carried a section titled "sim 侧预注册预期 (事后核对, 不许事后改)" - per-configuration behavioral signatures written before the session: s1e@0.8 the disturbance king (push 159/160, zero chirality, all-mu 20/20) at the cost of speed gates 0/20 and zero-command wander ~0.98 m with -29.5 deg/20 s rotation; fric-3000 "walks accurately but is easier to push over"; fric-2400 neither. Credibility check included: the sim harness had reproduced the already-recorded real behavior (pace in place + right drift + net rotation -30 deg/20 s), which "提高本单全部预期的可信度". The anomaly clause fixed the epistemics in advance: if results systematically disagree with sim, "不改结论改账" - don't massage the conclusion, write the discrepancy into the books, and per the earlier zero-warning lesson, hardware wins.
Change
Every hardware session ships with a pre-registered expectation table (signature per config), a baseline-match credibility check, and a written precedence rule for disagreement.
Outcome
The A/B session became falsifiable: agreement confirms the proxy, disagreement is booked as a proxy-bias finding rather than argued away.
Mechanism
Pre-registration converts qualitative hardware sessions into tests of the sim-to-real mapping itself; a reproduced known behavior calibrates trust in the remaining predictions; and fixing "who wins on disagreement" beforehand prevents authority from drifting to whichever source flatters the plan.
Applies when
- planning any hardware acceptance or A/B session
- the sim harness's credibility in this regime is unestablished
- post-session write-ups tempt narrative fitting
“⚠️ sim 复现了真机已记录的「原地踏步 + 右漂 + 净旋 −30°/20s」—— harness 与真机行为对得上, 提高本单全部预期的可信度。… 结果与 sim 系统性不符 → 不改结论改账: 写进 README 该节, 按 「Isaac 指标三次零预警」的教训, 以真机为准。”
train/REAL_RUN_S2.md § 2. sim 侧预注册预期 (事后核对, 不许事后改) / 4. 异常处置 Export every CAD part in the whole-machine frame so URDF rotations are zero and inertia is exact
urdf-shared-origin-exportGenerate the model so that correctness is structural: shared-origin STL export, zero rotations, subtraction-only origins, and an explicit 1e-9 g*mm^2 -> kg*m^2 conversion - never hand-rotate inertia tensors.
Symptom
Hand-assembled URDFs accumulate per-link rotation/origin errors and unit-conversion mistakes in inertia tensors - silent plant corruption that no later calibration can cleanly fix.
Context
Documented CAD -> URDF -> USD procedure from a successful Isaac Lab deployment, kept as the recipe if Lucen regenerates its model.
Change
(1) In CAD, align the whole robot to Z-up, X-forward (Isaac Lab convention) and ground the assembly; (2) export each STL with other parts hidden but the machine's shared origin kept, so all parts share one origin, every URDF rotation is 0, and inertia matrices equal CAD values directly; (3) units: Fusion 360 gives g*mm^2, URDF wants kg*m^2 - multiply by 1e-9; (4) link origin = negative of the joint position; link COM = CAD COM minus joint position; joint origin = difference of the two joint positions; (5) after URDF -> USD import, open the USD separately and set it instanceable before saving.
Outcome
A URDF whose rotations are all zero and whose inertia tensors are CAD-exact, eliminating an entire class of hand-transcription plant errors.
Mechanism
Keeping one shared origin turns every frame transform into a pure translation computable by subtraction, and leaves inertia tensors in the frame CAD already computed them in - no rotation of inertia tensors, the most error-prone manual step, is ever needed.
Applies when
- building or regenerating URDF/MJCF from CAD
- inertia or frame bugs suspected in the plant model
- importing URDF into Isaac Lab / USD
“导出 STL 时隐藏其他零件但导出整机——这样所有零件共享同一原点，URDF 里所有 rotation 全是 0，惯量矩阵直接等于 CAD 值 / 单位：Fusion 360 给 g·mm²，URDF 要 kg·m²，乘 1e-9 / link origin = 该关节坐标取负 … URDF → USD 导入后必须单独打开 USD 设成 instanceable 再存”
Experience.md § URDF 制作流程 (lines 87-92) Every gate on a penalty is an exit - to stop paying a stance tax the policy parked 2 deg outside a 30 deg uprightness gate (lunging), and, from scratch, just under a height gate (crouching); a positive band and an always-on guard fixed both
penalty-gate-is-an-escape-hatchNever gate a penalty on a state the policy can leave by getting worse; use always-on guards for what must never happen and positive, gated bands for what you want, and count every gate on a penalty as one more escape route to check in the logs.
Symptom
V2.9 added stance_width_task = relu(0.34 m - foot spacing) x standing gates, weight -10. Three checkpoints scored 0% on acceptance: standing height reached, feet on the ground, angular rate low, but the torso leaned 32.5/32.3/31.9 deg in a fore-aft lunge. The training dashboard read "tax paid off, base_height at full value".
Context
The penalty was gated by uprightness (tilt < 30 deg) and standing height; its tax had no time gate (500 steps x -1.65) while the standing income sat behind a 3 s zero gate (~325 steps), so leaning just past 30 deg lost a little gated income and saved the whole tax. base_height has no upright gate, so the lunge still collected it. The first metric also measured full horizontal spacing, so a staggered lunge counted as "wide".
Change
Two laws written down: a penalty may only carry gates the policy cannot escape by getting worse (make it an always-on guard) or it becomes a positive band ("not earned" is not "escaped"); and width is measured laterally in the base yaw frame. From scratch (V3.1 P1) with the lateral metric but the same gates, the policy parked just under the height gate instead (base_height 1.176/1.5, h ~ 0.30 m against a 0.3264 gate), the beta curriculum never advanced in 1,700 iterations, and the run was stopped early. P1b flipped the penalty into a positive band +2.0 x clamp(lateral / 0.34) x standing gates; P1c added yaw_guard = -5 x relu(|hip_yaw| - 30 deg), always on, no gate, no exemption.
Outcome
P1b: lateral stance 0.364 m, all four categories 100%, MuJoCo mu 1.0/0.4 both 100%. P1c: all six acceptance criteria passed for the first time on the line (hip-yaw saturation 1.2%), the guard's tax converging to -0.016 (almost never touched).
Mechanism
A gated tax that is not paid is saved, so the policy moves to the cheapest state just outside the gate; a gated income that is not earned is simply lost, so a positive band has no exit. HoST's style penalties are ungated or binary - the same law seen from the other side.
Applies when
- adding a penalty multiplied by an uprightness, height, phase or contact gate
- a policy settles just beyond a gate threshold
- training metrics look paid-up while acceptance collapses
“**罚项的门 = 策略的逃生门**。带直立门的负项可以靠"变得更差"(倾出门外) 全时免税;HoST 的 style 罚全部无门控/二值恰是同一律的反面实证。修律: 负项只许挂"变差逃不掉"的门(上限护栏 always-on),或改正向 band (收不到 ≠ 逃掉)。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §46 定案(血统内第四败 + 两条新律) Foot dragging is an attractor, not a low amplitude - and joint damping is the mode switch, adjustable at deploy time
swing-bistability-damping-switchWhen a quality metric is bimodal, stop treating it as an amplitude to be trained up: map the modes against initial conditions and plant parameters, find the parameter that switches basins, apply it first as a deployment lever, and only then bake it into the training distribution (as a plant-family shift, never as an execution-mapping change).
Symptom
s2e_pd-1400's swing height "median 12.1 mm" hid a perfect bimodal distribution: 20 seeds split into a drag mode (2.6-4.9 mm) and a step mode (19.3-24.0 mm) with NOT ONE seed in between - the median sat in the empty gap, and "swing debt -11 mm" really meant "50% probability of falling into the drag attractor".
Context
Two designed experiments closed the mechanism. Test A (nominal plant, 40 seeds): step 42% / drag 58% / middle 0 - at nominal gains, initial conditions alone pick the mode, both modes 100% survivable. Test B (fixed init, kp x kd grid): kd is the mode SWITCH - at kd 1.3 all surviving cells step (13-22 mm), at kd 0.7 nearly all drag (2.7-4.3), only at kd 1.0 does init get a vote; kp >= 1.2 is dangerous (5/6 falls). Global verification at kd x1.3 (20-seed, delay 2): survival 20/20 at ZERO cost, step share 42 -> 80%, swing median 12.1 -> 18.4 mm, slip record low 334, thicker tilt margin - costs: vx 85 -> 78%, saturation +5 pp. A Pareto sweep then priced the knob: step share 42/72/75/88/82/90 across kd 1.00-1.30 with a linear vx tax of -2.3 pp per 0.1 kd - the basin gain is fully collected at kd 1.20 ("1.30 是 over-damping 纯多付税"). Mechanism: low damping leaves a landing micro-oscillation / ground-slide channel the policy can exploit to drag; damping plugs the channel.
Change
Deployment lever adopted: kd-scale 1.20 (conservative 1.15) as the legitimate successor to the power-0.8 crutch ("前者削幅度保稳,后者堵 拖地通道换步态,且不牺牲存活"); training-side prescription: move the DR band to nominal-1.2 x (0.9,1.1) = [1.08,1.32], deleting the [0.7,1.0) drag-teaching zone - a contract-level change requiring digest re-baselining, gated on measuring the real robot's actual kd dispersion first.
Outcome
The kd surgery rung (s2e_kd) delivered basin 8 -> 11/20, slip 405 -> 331, vx 81 -> 85% with no out-of-band fragility (below-band check 20/20) - "拐杖烧进分布的正确姿势", explicitly contrasted with the failed s1g amplitude version: this one changes the plant family the policy has seen, that one changed the execution mapping the policy would have to relearn.
Mechanism
The gait's swing behavior is a bistable dynamical system whose basin boundaries are set by plant parameters; a policy trained across a kd band that includes the drag basin has learned to inhabit it. Shifting the deployed (and then trained) damping moves the system into the step basin without touching the policy - a plant-side fix for what looked like a training deficiency.
Applies when
- a gait quality metric splits into distinct modes across seeds
- deciding between more training and a gain/damping change
- converting a deployment crutch into a training-distribution change
“20-seed 里拖地模式 2.6~4.9mm 与迈步模式 19.3~24.0mm 各半,中间一个不落 … kd 是模式开关——kd1.3 下 6/6 存活格全迈步 … kd0.7 下几乎全拖地 … swing 债的解(至少大半)在部署端阻尼档,不在训练端 … 机理:低阻尼下落脚微振荡/贴地滑给了策略顺势拖行的通道,加阻尼堵之。”
train/README.md § swing 双稳态定性 + kd 部署杠杆 (2026-08-07, 用户设计 Test A/B) A 10 s acceptance episode left 6-7 s of standing to observe - a narrow stance held for that window and split on hardware; a gate cannot see instability slower than its own horizon
episode-length-bounds-what-a-gate-seesSize the standing phase of an acceptance episode, and its disturbances and floor friction, to what deployment will impose; a pass on a short static window certifies only that window.
Symptom
v2_6 passed every simulation gate (success 99.6%, re-falls 0-1%) and then, on the real robot, stood up and slid into the splits several times; prone starts stood and then fell backwards.
Context
Acceptance ran 10 s episodes; a ~1-2 s get-up left roughly 6-7 s of static standing on a nominal floor with no disturbance. The narrow stance's lateral margin and the straight-knee stance's lack of any flex buffer are both failure modes that need time, disturbance or lower friction to show.
Change
The gap was booked as a known blind spot of the gate ("long-duration standing stability") alongside the task-space stance criterion; later rungs added MuJoCo friction sweeps at mu 0.4 to every checkpoint scan.
Outcome
The spec through §50 records the blind spot but no longer standing window or disturbance row in the recovery acceptance itself.
Mechanism
An acceptance episode observes only the dynamics that unfold within its horizon under its conditions; slow drifts and disturbance-triggered failures are outside it by construction.
Applies when
- a policy passes sim gates and fails on hardware after a delay
- acceptance episodes are short relative to deployment use
- stability is judged without pushes or friction variation
“**sim 门为什么没逮住**:10 s episode 起身后只站 ~6-7 s,静态窗口内窄站距 撑得住;真机站立时长/扰动谱在门口径之外 —— 长时站立稳定性记为口径缺口。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §43 判读:sim 门为什么没逮住 When training fails repeatedly, inject the target behavior open-loop - stop tuning rewards for an unverified behavior
open-loop-probe-before-reward-tuningAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop on the real plant/sim first, and only resume training once you hold a measured, safe, sign-verified target trajectory.
Symptom
Three sidewalk training rounds failed; hypotheses multiplied (exploration failure / wrong reference waveform / insufficient authority) with no way to pick between them by running more training.
Context
Instead of a fourth reward guess, the team wrote probe_side_ref.py: the candidate reference is injected open-loop on top of a frozen policy's output (bypassing PPO entirely), directly measuring "what happens if the robot literally does this waveform" - separating all three hypotheses in one experiment (5 seeds x 8 s per condition, several waveform families and gains). The probe immediately eliminated the authority hypothesis (full-amplitude execution, 5/5 survival) and localized the problem to the waveform/measurement side. The closing principle was written down after the saga: without a verified target behavior, tuning rewards is "在黑暗里试钥匙" (trying keys in the dark).
Change
Standing method: before opening another training rung on a failing skill, build an open-loop (or task-space) generator of the intended behavior, measure whether the physical system can express it and what it looks like - then train toward a verified, quantified target.
Outcome
The probe chain produced the verified waveform (reversed-sign triangle, half gain), quantified safe amplitude (tilt 8.2 deg at band top, foot distance clear of the wall), exposed the metric bug when probe and training disagreed, and ultimately supplied the feed-forward that made C4 pass in +100 iters.
Mechanism
Training couples exploration, reward design, and feasibility into one opaque outcome; open-loop injection cuts the loop and tests feasibility and waveform alone. A behavior demonstrated open-loop converts the remaining failure into a pure credit-assignment/reward question - and its measured trajectory becomes the reference itself.
Applies when
- repeated training failures on one skill with multiple live hypotheses
- uncertainty whether the platform can physically express the behavior
- a reference trajectory's shape/sign/amplitude is guessed, not measured
“三轮 FAIL 之后不再猜，写 train/probe_side_ref.py 把参考开环注入到策略输出之上（绕过 PPO），直接量「照这个波形做会怎样」，一次分开三个假说：甲 探索 / 乙 波形 / 丙 权限。”
train/C_LADDER_RUN.md § 3f. C4 真因定谳（开环探针） / 3k. 建议的下一步 mj_objectVelocity returns inertial-principal-axis frame - one API assumption poisoned eval and observations for a whole line
body-frame-velocity-api-auditVerify every frame-sensitive API against a hand-computed truth (rotate raw qvel yourself, or command a known world velocity and check where it lands) before trusting any evaluation or observation built on it - especially when a model's inertial frame is rotated from its body frame.
Symptom
Sidewalk vy read ~0 under every condition; separately, whole-policy performance was mysteriously mediocre in sim2sim while training-side numbers looked fine. Four training rungs were declared FAIL partly on these readings.
Context
base_link's URDF inertial frame is rotated 90 deg about x relative to the body frame (iquat = [0.7071, 0.7071, 0, 0]). mj_objectVelocity(flg_local=1) rotates into ximat - the inertial principal-axis frame - not the body frame, and returns center-of-mass point velocity, not body-origin velocity. Consequences measured: the "vy" column was actually vertical velocity vz (walking at cmd 0.25: old reading +0.0093 vs true -0.0424); the angular velocity fed to the policy in sim2sim was [wx, wz, -wy] - a different quantity than Isaac and the real IMU provide. RMS check over 8 s of walking: y/z axes swapped between v6[:3] and the qvel truth.
Change
Fixed sim2sim and both probes to compute ang_b = qvel[3:6] and lin_b = xmat.T @ qvel[0:3] (identical quantity to Isaac's root_ang_vel_b / root_lin_vel_b), with a standalone reproduction script (frame_bug_repro_0809.py).
Outcome
Re-scoring the "failed" C4 lineage under correct coordinates reversed the verdicts: c4r4 checkpoints showed vy 80-126% tracking (old reading: +/-2%) and vx+0.30 at 91-95% where the old metric said 0/5 - the bad frame both mis-measured vy and, via corrupted policy observations, systematically depressed all measured performance. Final product passed 260/260 cells.
Mechanism
A simulator API's frame convention is part of the observation contract; when the model's inertial frame is rotated relative to the body frame, frame-agnostic use of a "local" velocity silently permutes axes. Feeding a policy an axis-permuted angular velocity is an observation corruption that degrades behavior everywhere, not just on the axis being studied.
Applies when
- building or auditing a cross-simulator evaluation harness
- one measured axis reads near-zero under all conditions
- sim2sim scores are inexplicably worse than training-side metrics
- URDF/MJCF inertial frames are rotated relative to body frames
“base_link 的 iquat = [0.7071, 0.7071, 0, 0] … mj_objectVelocity 用的是这个 … 喂给策略的 base_ang_vel 是 [wx, wz, −wy] —— MuJoCo 侧观测与 Isaac / 真机 IMU 不是同一个量；vy_mean 报的是竖直速度 vz —— 前进 cmd 0.25 时旧读数 +0.0093，真值 −0.0424。”
train/C_LADDER_RUN.md § 3l. ⚠️ mj_objectVelocity 读的是惯性主轴系 / 3m. 一 bug 坐实 The advisor's "runtime five-stage state machine + per-stage reference poses + RL residual" appeared in none of the three papers it cited - reading the originals changed the plan and downgraded two widely repeated industry claims
advisor-paraphrase-vs-paperRead the primary source behind any piece of advice before adopting its architecture; record where the paraphrase and the original differ, downgrade claims the originals do not support to speculation, and adopt what the verified sources actually share.
Symptom
After the violent first real run, an advisor proposed re-architecting recovery as a runtime staged state machine with reference poses and an RL residual, citing HoST, HumanUP and StableMimic.
Context
The three papers were read in full on 2026-08-09 and tabulated (deployment form, what the "stages" really are, hard constraints, references). HoST: one end-to-end policy, height-gated rewards in training, action anchored as q + beta*a with a beta curriculum. HumanUP: two training stages with the same observation/action; the vendor's three-stage state machine is the baseline it beats (41.7% vs 78.3%); Stage II tracks an 8x slowed Stage I trajectory (4x too violent, 10x does not converge). StableMimic: a learned soft gate. On 08-10 more sources were checked the same way: the Agility page does not say Digit's self-righting was learned in simulation (only step recovery is stated as RL), so the claim was downgraded to speculation; HoST's support for the 12-DoF armless Mini Pi exists in its code repository, not in the paper text.
Change
Adopted only what the originals share: a hard action bound or anchored action space, strong smoothing including a second-difference term, a slowed hidden reference, heavy DR and real fallen states. The staged runtime state machine was not adopted.
Outcome
The next re-rooting candidates came straight from the verified material, and the beta-anchored action space (HoST, with the Mini Pi configuration as the nearest real-robot precedent) became V2, the lineage that later stood up on hardware.
Mechanism
A paraphrase compresses a paper into the advisor's own architecture; only the original shows what was actually deployed, what was a baseline, and which numbers came with which ablation.
Applies when
- an advisor, agent or summary proposes an architecture with citations
- an industry claim ("X learned it in sim") is about to justify a design
- several papers are cited for one combined recipe
“⇒ **顾问的核心形态"runtime 五阶段状态机 + 每阶段参考姿态 + RL residual"在三篇引文 里均不存在**,其中 HumanUP 还点名 state machine 是局限。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §26 三篇引文精读判决(2026-08-09 全文核对;顾问转述与原文有出入) Ungated phase shaping made standing 42x more expensive than stepping - and the stepping was cooking the hip motors
moving-gate-42x-stand-taxGate every phase/clock-driven shaping term on the command that justifies motion, price the cmd=0 case explicitly during design - and when a reward flaw is sim-only, book it with trigger conditions instead of operating immediately on a working lineage.
Symptom
At cmd = 0 the sim policy never stood still - it stepped in place and crept 0.98 m per 20 s; on the real robot the same lineage's stepping made hip_roll motors run 20 degC hotter than every other joint (43-48 degC vs 25-28).
Context
The arithmetic closed it: the three phase-shaping terms (joint_pos_ref 1.6, feet_contact_number 1.2, feet_clearance_swing 1.6) are driven by the gait clock with NO command gating, so standing at cmd=0 forfeits 3.32/step of shaping while honest standing earns only 0.078 of tracking - stepping wins 42x. The heat chain: perpetual stepping = perpetual single support = one hip_roll stalled at ~4.3 N*m (25% of torque limit) carrying the torso's frontal-plane moment - two hip_rolls = 90% of whole-machine steady-state I2R; measured stand-vs-step comparison: total heat -71% when actually standing. The suspended test acquitted the actuator (0.21 rad sag -> 0.0008 rad in air) and mechanics vetoed the easy fix ("降 kp 救不了热" - equilibrium torque equals the external load regardless of kp). The fix (moving_gate: hard-gate the three shaping terms on |cmd| > eps) was designed - then DEFERRED by the user because the real robot at the time stood fine: "真机不表现该问题, 为真机不存在的病改奖励表不划算", with written trigger conditions (C-ladder stand row persistently failing, or real robot starting to step/drift at cmd=0) and the known hazard tag (this is exactly the reward-change class that triggers the B-arm signature). When the real robot later DID step and cook, the booked trigger fired and moving_gate moved from debt to to-do with its benefit re-priced: "停止空烧 hip_roll,稳态发热降 ~71%".
Change
moving_gate designed with the gate_by_cmd convention; deferral, triggers, and expected heat recovery all pre-registered instead of patching the reward for a then-sim-only symptom.
Outcome
The cmd=0 stepping went from mystery to closed arithmetic; the thermal measurement (hip_roll +20 degC) quantitatively confirmed the 90%-of-heat prediction; the reward change waited for real-world justification instead of spending a risky revision early.
Mechanism
Clock-driven shaping terms define a perpetual-motion bounty unless gated by command; the resulting idle gait is not a training bug but the table's optimum. Its cost surfaces on hardware as stall-torque heating set by statics (mass x lateral offset), which no gain change can remove - only removing the motion (gating) or widening the stance can.
Applies when
- the policy steps in place or creeps at zero command
- specific joints run hot in idle behaviors
- deciding when a known reward flaw justifies a risky mid-lineage fix
“塑形合计 −3.32/步 … 净: 站定亏 42 倍 … 两颗 hip_roll 4.29 / 4.09 N·m(各占限扭 25%),占全机稳态 I²R 的 90% … 吊挂实测 hip_roll 跟踪误差 0.21 rad → 0.0008 rad … 降 kp 救不了热 … 真机不表现该问题, 为真机不存在的病改奖励表不划算”
train/README.md § C1 FAIL 节 (cmd=0 的 sim/真机分歧记账) / C2 真机 A/B 三b 发热定性 Calibrate a wall penalty by measuring healthy and sick policies - healthy pays ~0, the disease pays a wall
calibrate-threshold-between-healthy-and-sickCalibrate every threshold penalty by evaluating its exact formula on replays of at least one healthy and one sick policy: place the threshold between their distributions, size the weight so the sick policy pays a decisive fraction of tracking while the healthy one pays ~0, and pre-compute neighboring thresholds for cheap adjustment.
Symptom
Real walk_v7 occasionally clipped its own legs (stance narrowed to 133 mm mean vs nominal 214.5); a foot-distance penalty was needed, but an uncalibrated threshold/weight risked either doing nothing or becoming a reverse barrier.
Context
The term (relu(d_min - lateral foot distance), measured in the base yaw frame because world-frame y is meaningless after turning) was calibrated before training by replaying three known policies through the exact reward formula at the acceptance operating point: healthy v5 (183 mm) pays 0.6% of tracking - effectively free; narrowed v7 (133 mm) pays 22% - effective widening pressure; collapsed v8 (93 mm) pays 55% - a wall. d_min 0.16 was placed deliberately between healthy and sick, with alternative thresholds (0.14/0.18) pre-computed in the tool output for later adjustment. The shape self-check was named as a standing question: "先问'零代价的选项是什么'" - the zero-cost region must be exactly the desired behavior.
Change
feet_lateral_distance added at d_min 0.16 / weight -10, with telemetry expectation pre-registered (should decay toward 0 as stance learns >160 mm; if bow-legged over-widening >214 appears, only then discuss an upper bound).
Outcome
v9_probe on hardware: no leg contact ("没碰腿(N2 兑现)"), stance min 145/126 mm green; the term's zero-cost design left healthy gait untaxed.
Mechanism
A relu threshold penalty defines a free region and a priced region; its correctness is entirely in where the boundary sits relative to the healthy and pathological distributions. Replaying known-good and known-bad policies through the exact formula measures both distributions in the term's own currency, making the threshold and weight a placement decision instead of a guess.
Applies when
- adding any relu/threshold-style wall penalty
- a safety margin (foot distance, joint limit, clearance) needs enforcement without taxing normal behavior
- choosing between candidate thresholds for a new term
“形状自检 (v6 横向组/v8-B 的教训 —— 先问"零代价的选项是什么"): 标称站距付 0, 健康步态付 ~0, 收窄才付费 … v5(健康) 183 mm … 0.6% ≈ 免费 | v7(收窄) 133 mm … 22% —— 有效推宽 | v8(塌陷) 93 mm … 55% —— 墙 … d_min=0.16 恰在 v5(183)与 v7(133)之间”
train/WALK_V9_SPEC.md § 2. N2 —— 脚距惩罚(已完成权重预标定) After seven patch-generations, freeze the lineage as a regression baseline, fix the structural debts, and retrain from zero
freeze-lineage-fix-structure-restartWhen successive rungs keep trading one symptom for another, ask whether the remaining problems are structural (contracts, latency, sampling, reward-table architecture); if so, freeze the lineage as regression baselines, pay the structural debts, and restart minimal - carrying forward laws and instruments, not weights and weights' patches.
Symptom
The v5-v11 walk lineage had accumulated interacting patches (reward terms, gates, clamps, per-joint scales) faster than it converged on the user's goal; v12's spec itself was superseded before training by an external review's verdict that the remaining problems were structural, not parametric.
Context
The 2026-08-05 status banner records the pivot: the walk profile was rolled back wholesale to v10b parameters, the v5-v11 lineage frozen "只作回归对照" (kept only as regression baselines), and four structural debts were named as prerequisites for a from-zero straight-walk baseline: the action-latency FIFO (fixed with its own test), the ONNX manifest contract, discrete command sampling, and a minimal reward table. The v12 spec - fully designed, partially implemented - was suspended: "本规格挂起,不再按此开训".
Change
Strategy switched from "one more patch generation" to freeze-fix-restart: lineage checkpoints retained as comparison anchors, infrastructure hardened first, then a clean retrain with a minimal reward table (this restart produced the s* generation that later became the real-robot SOTA line).
Outcome
A designed-and-ready training generation was deliberately not run - the review's structural findings outranked sunk design cost; the restart line inherited seven generations of laws (calibrations, gate batteries, falsified fixes) without inheriting their entangled reward table.
Mechanism
Patch lineages accumulate coupled terms whose interactions eventually cost more to reason about than a restart costs to train; the knowledge worth keeping is the laws and instruments (measured plant values, calibrated gates, falsified directions), not the entangled weights. A restart on hardened structure converts the lineage's lessons into a clean initial design instead of another delta.
Applies when
- repeated rungs shuffle symptoms without net progress
- an external review flags infrastructure/contract debts
- deciding between another patch generation and a clean retrain
“同日外部评审定调换路线:冻结 v5~v11 血统(只作回归对照),修结构性问题(latency FIFO 已修 tests/test_action_latency.py、ONNX manifest 契约、离散命令采样、最小奖励表)后从零训直行基线。本规格挂起,不再按此开训。”
train/WALK_V12_SPEC.md § ⚠️ 状态 (2026-08-05) A ratio metric flipped the verdict - spectral share rose while absolute high-frequency energy fell 16%
ratio-metrics-need-absolute-checkNever compare share/percentage/centroid metrics across conditions whose totals differ; pair every ratio with its absolute numerator before issuing a verdict, and log retracted judgments so they are not re-derived.
Symptom
walk_v6 was provisionally judged "more jittery" than v5 because the joint-velocity spectral centroid rose 2.91 -> 3.62 Hz and the >4 Hz energy share rose 12.6% -> 17.8%.
Context
Absolute measures said the opposite: first differences of actions fell 1.54 -> 1.31, second differences 2.55 -> 2.19, and absolute high-frequency energy fell 16% (0.490 -> 0.413). The shares and centroid rose only because low-frequency content fell even more - the denominator shrank. The interim judgment was retracted in writing so it would not be reused.
Change
Metric discipline noted: "占比类指标在总量变化时不能直接比较" - share/ratio metrics are not comparable across conditions when the total changes; verdicts about smoothness must cite absolute energies or difference norms.
Outcome
v6 correctly classified as smoother, not jitterier; the retracted judgment logged under "被推翻的一个中间判断(记下来免得复用)".
Mechanism
A ratio confounds numerator and denominator; any intervention that removes low-frequency content raises every high-frequency share without adding a single joule of jitter. Only absolute quantities support cross-condition comparison when totals move.
Applies when
- comparing smoothness/jitter/spectral metrics across versions
- any percentage-based metric moves after an intervention
- writing an eval report that includes normalized quantities
“我一度说"v6 动作更抖" … 错了: 动作一阶差 1.54→1.31、二阶差 2.55→2.19 都在降 … 谱质心升高只是因为低频成分掉得更多, 绝对高频能量实际下降 16%(0.490→0.413)。占比类指标在总量变化时不能直接比较。”
train/WALK_DIAGNOSIS.md § 过程中被推翻的一个中间判断(记下来免得复用) Measure yaw rate by integrating heading, not by averaging body-frame angular velocity - the two differed 15x
heading-integral-not-body-rateFor any secular rate (turn gain, drift), integrate the world-frame angle over the window; never average instantaneous body-frame rates during oscillatory motion - and when code comments warn about a measurement, believe them before re-measuring.
Symptom
Two measurements of the same turn gain disagreed by a factor of ~15: time-averaged body-frame omega_z gave -0.05 while the sim2sim harness's heading-angle integration gave +0.473.
Context
The harness code comment had already documented and predicted the failure: during gait the torso oscillates (body-frame omega_z std up to 0.7); projecting world angular velocity onto a swaying body axis and then averaging biases the estimate systematically - "实测体系均值 −0.04 而实际在以 +0.15 转" (measured body-frame mean -0.04 while actually turning at +0.15). The author's own -0.05 measurement was declared void and the training machine's 1.58/2.45 turn gains confirmed valid.
Change
Measurement doctrine fixed: yaw rate for evaluation = net heading change by integration over the window; instantaneous body-frame rates are unusable for averaged directional statistics during legged gait.
Outcome
Subsequent friction sweeps and turn-gain accounting were all conducted in the heading-integral currency, making cross-simulator comparisons (MuJoCo vs Isaac 1.04/1.02) meaningful.
Mechanism
Averaging a vector quantity expressed in an oscillating frame couples the frame's oscillation into the mean (a rectification bias); the heading integral is computed in the world frame where the gait oscillation integrates to ~zero, leaving the secular component.
Applies when
- measuring turn gain, heading drift, or any secular angular rate
- a body-frame-averaged statistic disagrees with trajectory-level truth
- writing evaluation code for oscillating platforms
“我用体坐标系 ωz 的时间均值测,得 −0.05;sim2sim 用航向角积分,得 +0.473。差 15 倍。… 步态中躯干摇晃(体系 ωz std 可达 0.7),把世界角速度投到摇摆的体轴上再取均值会系统性偏掉 … 结论:偏航率必须用航向积分,体系瞬时角速度取均值不可用。”
train/WALK_DIAGNOSIS.md § ③ 转向增益 —— 我的测法是错的,训练机的 1.58/2.45 成立 Add a single-point-suspension test to acceptance - the ground is a free stabilizer that hides divergence
suspension-probe-removes-free-stabilizerInclude at least one acceptance condition that strips the environment's free stabilization (suspension, or equivalent) - the sim-passing policy that fails on hardware is often failing a condition the battery never posed.
Symptom
walk_v5 looked healthy in every on-ground sim test yet diverged on the real robot - the acceptance battery had never measured a condition that would have revealed it.
Context
The battery gained a single-point-suspension probe (robot hung, feet free): measure torso tilt while the policy runs without ground contact. v5 scored 45.9 deg mean tilt suspended - wildly unstable - which the file calls "最灵敏的失稳探针(拿掉地面这个免费稳定器)": ground reaction forces passively stabilize a marginal policy, so on-ground metrics saturate long before the policy's internal balance is actually sound. v6 halved it (23.0 deg, target <10 deg) - progress visible on a scale where on-ground numbers showed nothing.
Change
Suspended-tilt added as a standing acceptance row; run under the honest contact parameters battery (accept_v2 with measured condim 4 / torsional friction 0.035), under which v5 correctly FAILS in agreement with the real robot.
Outcome
The sim battery's verdict on v5 flipped from pass to fail, matching hardware; suspended tilt became the discriminating metric between v5 and v6 (45.9 vs 23.0 deg) when ground metrics differed little.
Mechanism
Contact with the ground closes a stabilizing feedback loop the policy gets for free; removing it exposes the policy's own attitude control authority. A metric measured only in the assisted condition cannot rank policies by the unassisted quantity that hardware will actually demand during perturbations and flight phases.
Applies when
- sim acceptance passes but hardware diverges
- designing an acceptance battery for a legged robot
- two candidates tie on ground metrics
“单点吊那条是最灵敏的失稳探针(拿掉地面这个"免费稳定器"), v5 在地上一切正常却在真机发散, 就是因为验收从没测过这个工况。”
train/WALK_V6_MINIMAL.md § 5. 验收 One fixed acceptance matrix for every rung - new skill must PASS while every old skill stays within a regression budget
fixed-acceptance-matrix-per-rungFreeze one acceptance matrix for the whole ladder; every promotion requires the new skill's PASS plus bounded regression on every prior skill, measured against the parent's baseline under the current (bug- fixed) metric code - and include command transitions, not just steady states.
Symptom
Sequential skill training silently trades old skills for new ones (C1 trained away the root's backward ability); without a constant measurement frame, each rung's numbers are incomparable and regressions hide.
Context
The C ladder ran the same 13-cell command matrix at 20 seeds per cell at every rung (stand; vx +0.15/+0.30; vx -0.10/-0.20; vy +/-0.10; wz +/-0.20; two vx&wz combos; two vx&vy combos), with promotion requiring "新技能 PASS 且旧技能不明显退化" - old-skill regression budget <=2/20 against the parent's recorded 20-seed baseline. For the transition-rich final rung, a command-switch block was added (forward->stop, stop->backward, forward->turn, left->right, turn->forward; survival + re-track within 2 s) because "每个 steady command 都会做 ≠ 命令切换不会摔" - steady-state success does not imply switch safety, and the joystick does switches. The C4 product's gate ran 260 cells (13 x 20) all 20/20.
Change
Battery frozen once, reused verbatim per rung; baselines re-measured per parent (and re-measured again after the metric-frame fix, since old baselines were taken with the buggy coordinate reading - "旧基线是坏坐标系的， 不可引用").
Outcome
Regressions were caught at the rung that caused them (C1's backward loss, C2's vx+0.30 decay), and cross-rung comparisons stayed valid for the ladder's whole life.
Mechanism
A constant matrix makes every rung's output a point in the same metric space, so "did we lose anything" is a table diff, not a judgment call; the per-skill regression budget converts previously earned PASSes into standing constraints on all future training.
Applies when
- designing gates for sequential skill addition
- promoting a checkpoint to be the next rung's root
- after any evaluation-code fix (old baselines must be re-measured)
“新技能 PASS 且旧技能不明显退化才晋级。… C5 追加：命令切换验收（steady ≠ transition） forward→stop、stop→backward、forward→turn、left→right、turn→forward，各 20 seed，判存活 + 切换后 2 s 内是否重新跟上。”
train/C_LADDER_RUN.md § 5. 固定验收矩阵（每级跑同一张，每项 20 seed） Freeze the deployment contract, stamp every export, and let an automated checker catch wiring bugs
contract-freeze-and-checkerFreeze and fingerprint the policy I/O contract; ship contract changes as new versioned profiles that leave old artifacts bit-identical; and extend the automated contract checker with every pipeline change, forcing the new path to execute in the check.
Symptom
Contract-level changes (observation layout, action pipeline) are where silent sim/real divergence is born; two real wiring bugs appeared the one time the action pipeline was extended.
Context
The 215-dim observation contract was frozen ("纪元 3，三机 digest" - an era number plus a digest agreed across three machines); proposals that would break it (e.g. a GRU memory) were rejected on contract grounds. Every exported ONNX is stamped and verified with a manifest (onnx_manifest --stamp / --verify), and deployment refuses mismatched combinations. When C4 added the lateral feed-forward, it went in as a NEW profile (omni_ff) leaving the existing omni profile's behavior bit-identical; the checker (check_contract) was extended to force the feed-forward path to actually execute (cmd_vy=0.13) and promptly caught two genuine bugs: (1) re-clamping with soft_joint_pos_limits after the feed-forward (0.23 rad deviation) instead of reusing the parent's clip; (2) indexing processed actions by asset.joint_names instead of the action term's own contract-ordered _joint_names, which landed the feed-forward on the wrong joints (l_hip_yaw / r_ankle_pitch).
Change
Contract discipline as implemented: frozen dims + digest; manifest stamping and refusal; contract changes only via new versioned profiles; checker updated in the same commit as any pipeline change, with inputs chosen so new code paths are exercised.
Outcome
Both wiring bugs caught before any training or deployment ("两个都是 check_contract 当场抓出来的 —— 这次它值回票价"); old deployments provably unaffected by the new profile.
Mechanism
The contract is the only interface the policy and robot share; freezing plus fingerprinting makes divergence detectable, and an executable checker turns "the contract holds" from a belief into a test - but only if its inputs actually drive the new code path.
Applies when
- modifying the action or observation pipeline of a deployed policy
- exporting policies for hardware
- proposals that would change observation dims or history structure
“契约校验抓到的两个真错误（记账，别再犯）：1. 前馈后误用 soft_joint_pos_limits（URDF 限位 ×0.9）重钳 → 0.23 rad 偏差 … 2. 用 asset.joint_names 索引 _processed_actions → 前馈落到 l_hip_yaw/r_ankle_pitch 上 … 两个都是 check_contract 当场抓出来的 —— 这次它值回票价。”
train/C_LADDER_RUN.md § 3j. 契约级改动 / 契约校验抓到的两个真错误 Changing the gait clock silently flipped a hardwired threshold's meaning - write derived constants as expressions
derived-constants-must-track-their-baseBefore changing any base parameter (clock, control rate, scale), enumerate every constant derived from it and every constant that must NOT change; convert derived literals into expressions of the base so the next change cannot silently flip a term's meaning.
Symptom
Slowing the clock 0.40 -> 0.50 s would have silently inverted the feet_air_time threshold's semantics: the 0.25 s threshold was hardwired, so at ct 0.40 the swing window (~0.20 s) sat below it (constant pressure to lengthen strides), while at ct 0.50 the window (~0.25 s) equals it - the term's meaning flips from "push longer" to "neutral" with no code error anywhere.
Context
The clock change audit walked every dependent quantity: most followed automatically (joint_pos_ref / clearance / contact_number cycle_time params, gait_phase observation, deploy/sim2sim/policy_io, export) - wiring confirmed, zero hand edits; the air_time threshold was the one hardwired constant, fixed by preserving the RATIO: 0.25 -> 0.3125 = 0.625 x ct, with the recommendation to commit it as the expression 0.625*ct "一劳永逸" (solved once and forever). The same audit also listed what must NOT follow the clock (50 Hz control rate, physics dt/decimation, 47-dim contract, action_latency absolute seconds, PD/torque limits) - the change's blast radius stated in both directions.
Change
feet_air_time threshold re-expressed as a fraction of cycle_time; auto-following vs must-not-change lists written into the spec for the clock migration.
Outcome
The clock migration (v10, repeated in v11) carried no silent semantic flips; the expression form removed the trap for every future clock change.
Mechanism
Constants derived from a base parameter encode a ratio at their birth; storing the evaluated number severs the dependency, so changing the base leaves stale semantics with no failing test. Expressions preserve the intent; and an explicit both-directions dependency list (follows / must-not-follow) is what makes a base-parameter change reviewable.
Applies when
- changing gait clock, control frequency, or units
- a reward threshold interacts with a phase/window duration
- config audit finds literals that encode ratios
“feet_air_time 阈值 0.25 是写死的,不跟 ct 走——0.40 时摆动窗 ~0.20s<0.25(恒拉长压力),0.50 时摆动窗 ~0.25s≈阈值(语义翻转)。按比例保原压力:0.25 → 0.3125(=0.625×ct;建议直接写成 0.625 * ct 表达式,一劳永逸)。”
train/WALK_V10_SPEC.md § 3. T —— 慢时钟 (训练侧必做一件) An exponential kernel on instantaneous velocity punishes gait oscillation - track the cycle average
cycle-average-tracking-for-gait-quantitiesReward velocity tracking on gait-cycle averages (or filtered values), not instantaneous samples, whenever the desired behavior oscillates at stride frequency; widening the kernel does not fix a variance penalty.
Symptom
Even while the robot genuinely sidewalked (verified after the metric fix), the Isaac-side tracking reward sat on the ignore-floor: true sidewalk scored 0.178 vs 0.189 for ignoring the command - the reward was mildly punishing the desired behavior.
Context
Sidewalking is inherently oscillatory: per-frame vy std was 0.177 while the tracking kernel width was sigma = 0.15, applied to the instantaneous value. A kernel-width scan showed widening sigma 0.15 -> 0.50 still loses (-0.14 -> -0.07): "指数核惩罚的是方差，而侧步天生带方差" (the exponential kernel penalizes variance, and side-stepping inherently carries variance). Modeling with measured parameters: replacing instantaneous vy with the mean over one gait cycle (0.5 s) flips the margin decisively (true sidewalk 1.888 vs ignore 1.281, +0.607), half-cycle is neutral (+0.006), two cycles adds nothing more. Explicitly flagged as extrapolation pending Isaac-side implementation. This also vindicated a previously dismissed external note (sigma too small) - right conclusion, different mechanism than claimed (variance, not gradient).
Change
Proposed fix recorded: change the tracked quantity from instantaneous vy to a one-gait-cycle running average; widening sigma alone rejected by the scan.
Outcome
Diagnosis complete and quantified; the C4 product shipped via feed-forward before the reward change was implemented, so the cycle-average fix remained a verified-by-model, not-yet-trained change.
Mechanism
E[exp(-(v-c)^2/sigma^2)] decreases with Var(v) even when E[v] = c exactly; a gait's phase-locked oscillation guarantees variance at the stride frequency, so instantaneous tracking rewards structurally prefer standing still at the command mean. Averaging over exactly one cycle removes stride-frequency variance while preserving command-following error.
Conflicts
The cycle-average fix itself is model-extrapolated ("⚠️ 这一条是外推，须在 Isaac 侧实装并复量后才能当结论") - the diagnosis is measured, the remedy untested in training at the time of writing.
Applies when
- tracking rewards for lateral/turn/any oscillation-carrying velocity
- a verified behavior scores below the ignore-floor
- choosing sigma for exp-kernel tracking terms
“侧走时 vy 的逐帧摆幅 std = 0.177，而 track_lin_vel_y_exp 核宽 σ = 0.15，且作用在瞬时值上 … 真侧走（均值 66%，振荡 ±0.18）0.178 | 完全无视指令 0.189 … 真侧走的得分比无视指令还低。… σ 从 0.15 放到 0.50，侧走仍然吃亏 … 把跟踪目标从瞬时 vy 换成一个步态周期（0.5 s）的平均 vy：… 1.888 vs 1.281”
train/C_LADDER_RUN.md § 3n. 二/三 Isaac 训练奖励为何一直坐在「无视底分」/ 修法不是放宽 σ The get-up kept getting faster because standing earlier paid more every step - lowering torque authority barely slowed it, and only zeroing the standing income for the first 3 s moved the pace into the design band
per-step-income-drives-speed-time-gateWhen a skill is too fast, find the term that pays for finishing early and gate that income by time; keep the "get into position" term ungated so the policy does not learn to wait, use a ramp instead of a cliff, and confirm with a paired same-level experiment that the drift is motivational before changing it.
Symptom
The user judged the get-up too fast (Isaac medians about 0.7-1.6 s) and suspected path dependence: the policy seemed to get faster the longer it trained.
Context
Lowering the beta authority 0.40 -> 0.30 cut impact but moved supine only 1.70 -> 2.00 s: coordination-limited, not torque-limited. A paired experiment inside one beta level (checkpoint 15,600 vs 18,499, +2,900 iterations, same ruler) measured the drift: get-up medians -7 to -10%. The spec concluded the motive, not the path, was the cause - per-step standing income pays for every early step, and any lineage (even one from scratch) races toward the fastest solution inside its constraints.
Change
V2.5: the standing income (base_height, stand_pose, still, feet_on_ground) multiplied by w(t) = clamp(t/3 s, 0, 1); upright deliberately NOT gated, so righting and sitting up early still pay and the policy is not taught to lie flat and wait; a ramp, not a step. V2.5b: zero before t0 = 3 s, then a 1 s ramp.
Outcome
V2.5: Isaac 100%, get-up +17-43% slower, MuJoCo 100/100/98/100% (the best cross-simulator reading yet), still short of the 3.5-4.5 s design band - a linear ramp only discounts early income. V2.5b: MuJoCo supine 2.04 -> 4.10 s and prone 3.18 -> 4.04 s, inside the band; the Isaac pace barely moved (a lineage habit on a gradient-free plateau). Later the zero gate proved harmful when trained from scratch (curriculum-history-is-part-of-the-product) and in the V3.1 lineage (time-gate-vs-wide-stance-retire-the-fix).
Mechanism
Constraints on authority or velocity change how the fastest solution looks; the time structure of the task income decides how fast the fastest solution is.
Applies when
- a policy is faster or more aggressive than wanted and constraints do not slow it
- progress-style rewards pay every step spent at the goal
- performance drifts faster with more training at fixed settings
“**V2.5 机制(唯一)**:站立收入(base_height/stand_pose/still/feet_on_ground) 乘时间斜坡 w(t)=clamp(t/T_gate,0,1),T_gate=3.0 s;**upright 刻意不门控** (翻正/坐直早期照常拿钱,防"躺平等门开" … **用户假设量化 证实:逐步计酬动机在 β 包络内持续压缩时间,约束挡不住动机 —— V2.5 动机层 修法为正解。**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §39 V2.5 预注册 / §39 补 配对实验 A training-side rate limit anchored on the last commanded target is an integrator inside the balance loop - two unrelated lineages converged to the same 34-43% re-fall rate, a soft penalty could not fix it, and the bandwidth arithmetic said safety and standing could not coexist
slew-anchor-is-an-integratorIf you constrain actions in training, anchor the constraint on the measured state, not on the previous command - a limiter with memory adds lag inside the balance loop; and when two different lineages converge to the same failure rate, treat the cause as structural and stop adding soft penalties.
Symptom
With the rate limit moved into training (V1), policies either could not stand up or stood up and kept falling again: the stand oscillated, fell and climbed back, 34-43% of the time.
Context
V1.0-B (user decision: explore new postures from scratch, hard constraint in training): target <- prev + clip(target - prev, +/-S*dt) at the TIGHT rates, anchored on the last issued target like the bridge. Four runs: v1_0 from scratch 0.8% - every category righted under the limit, then knelt (the limit also damped the exploration that had escaped the seated basin in V0); v1_0c continued from R3.1 99.8% get-up but 36-43% re-fall and knee jitter 0.604 rad/s; v1_0p with a pull-assist curriculum (56 N -> 0, fully withdrawn) 39.1% unassisted, re-fall 34-42%; v1_0w with a windup-gap penalty 25.4%, re-fall 18-43%. Removing the limiter from v1_0p gave 0.0%: the policy had co-adapted with it.
Change
The rate-limit route was declared dead after four runs and the line was re-rooted on a beta-anchored action space (V2, user approval required).
Outcome
V2.0's first acceptance at full authority already showed re-falls of 0-1% (V1: 34-43%), the structural bet paying off before any tuning.
Mechanism
Anchored on the previous command, a saturated policy becomes a rate controller - one more integrator in the loop - and active balance through that lag oscillates, while a kneeling sit needs no active control and is stable. The arithmetic: kp 30 needs 0.4 rad of error for 12 N*m; at 4 rad/s that takes 0.1 s, half the pendulum time constant sqrt(0.38/9.8) ~ 0.2 s; keeping standing bandwidth needs S of at least ~8 rad/s, within 20% of the 10 rad/s velocity limit - no bound at all. Anchoring on the measured angle (q + beta*a) makes the full kp*beta authority available in one step, with no memory, and caps the impact at the same time.
Applies when
- adding rate limits, slew limits or target filters to a policy's action path
- a policy stands but oscillates and re-falls after a constraint was added
- different lineages or curricula land on the same failure signature
“v1_0p(拉力课程):会站(prone 79.9%),再摔 34~42% —— **两条完全不同 血统、不同学习路径,收敛到同一失败率**。 … 动作饱和时它退化为 速率控制 = 环内多一个积分器;主动站姿平衡穿过该滞后必振荡(v1_0 的跪坐不需 主动控制,所以稳)。对照:**HoST 的 β 锚在当前实测 q,无记忆、无积分器**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §31 结构病定案:slew 的目标锚 = 控制环里的积分器 Mirror augmentation over an asymmetric default injects systematic error - symmetrize the default first and verify the transform bit-exact
mirror-augmentation-needs-symmetric-defaultBefore enabling any symmetry augmentation, make every constant inside the observation encoding exactly symmetric, and validate the mirror transform against forward kinematics to machine precision - an unverified augmentation is a new error source, not a regularizer.
Symptom
Mirror data augmentation was about to be added while both default poses (standing_pose, walk nominal_pose) were asymmetric - stale hand-tuned compensations from before a ground re-calibration, with hip_yaw differing 2.40 deg between sides and the foot soles actually tilted (pitch 2.88/1.35 deg, roll -2.47/+0.25 deg).
Context
The observation encodes joint_pos_rel = q - default. Under mirroring q_l -> -q_r, the relation (q-default)_l -> -(q-default)_r holds only if default_l = -default_r; with an asymmetric default, augmentation produces observation pairs that are NOT mirror images, i.e. "default 不对称时做镜像增强会引入系统性错误,比不做还糟" (worse than not doing it). The fix: adopt model geometric zero as standing default (MuJoCo FK verified: sole pitch/roll exactly 0, asymmetry 0.00 deg) and a symmetric crouch for walk (hip -0.25/knee -0.5/ankle -0.25 satisfying hip - knee + ankle = 0 to keep soles flat). The mirror transform itself was verified bit-exact before use: pseudovector vs polar-vector sign patterns (ang vel [-1,1,-1], gravity [1,-1,1], cmd [1,-1,-1]), joint swap-and-negate; FK check that left-foot pose under q equals the mirror of right-foot pose under mirror(q), measured error 0.00e+00.
Change
Defaults symmetrized first (with init heights recomputed by FK), stand policy retrained on the new default so both policies share one default; augmentation enabled only after the FK mirror test passed.
Outcome
stand_v1 achieved exact left/right pairing (l_knee -0.1013 / r_knee +0.1013), six-pair asymmetry 0.0 deg, height fluctuation 7 -> 1 mm, 33% less mean |action|.
Mechanism
Augmentation asserts an equivariance of the observation encoding; any asymmetric constant inside the encoding (the default) breaks the asserted symmetry, so the augmented data teaches a false invariance. Verifying the transform against FK geometry tests the assertion end to end, independent of the training stack.
Applies when
- adding mirror/symmetry augmentation to locomotion training
- defaults or trims were hand-tuned per side at any point
- observations are expressed relative to a default pose
“观测里 joint_pos_rel = q − default。镜像下 q_l → −q_r,要让 (q−default)_l → −(q−default)_r 成立,必须 default_l = −default_r。default 不对称时做镜像增强会引入系统性错误,比不做还糟。… 位置误差与姿态矩阵误差实测均为 0.00e+00。”
train/RETRAIN_v2.md § 2. 前提:default 姿态必须先对称化(不是可选项) / 3. 镜像变换 Real robot walked at half the sim clock for two generations - resolved by racing a reward-side and a plant-side evidence line, not by guessing
period-doubling-evidence-raceFor a hardware-only pathology, refuse to guess: pre-register one probe per side of the sim2real boundary (can the reward mechanism change it on hardware? can fitted plant parameters reproduce it in sim?) and let the first positive result direct the next version.
Symptom
The number-one sim2real gap: on hardware v6/v7 stepped at 1.23-1.32 Hz - almost exactly half the 2.50 Hz gait clock they were trained and simulated at; sim never reproduced it, two generations running.
Context
Instead of committing training budget to a guess, v8 pre-registered two mutually controlled evidence lines and kept the clock OUT of the training variables: (a) reward-side - if the v8 saturation fix revives joint_pos_ref (the term that pins the gait to the clock), re-run hardware and see whether frequency returns to 2.5 Hz (hypothesis: v7's frozen actions meant NO reward was pinning the gait to the clock, and the real plant - with armature and friction making high frequencies expensive - slid down to the leg's pendulum natural frequency ~1.1 Hz); (b) plant-side - record suspended joint data (fit_actuator), fit armature/friction, load the fitted values into sim2sim and see whether the 1.25 Hz reproduces IN SIM. Decision rule fixed in advance: "谁先给出阳性结果谁定 v9 的方向 (奖励侧 vs plant 侧)" - whichever line goes positive first sets the next version's direction.
Change
Period-doubling excluded from the v8 change set; both diagnostic lines scheduled in parallel as non-blocking work; frequency reported factually in acceptance with no pass/fail attached ("倍周期是否消失 不设判定,它是 §9 的关键证据").
Outcome
The gap was routed into a decisive-experiment structure rather than a speculative retrain; the plant-side line pointed at exactly the unmodeled armature/friction that were later measured and installed as the plant baseline. Resolution (era-2c full-plant retest): the family had TWO causes - v8's low-speed period-doubling vanished once measured armature+friction were installed (1.30 -> 2.50 Hz, bifurcation-edge machine sensitivity), while v7's stood untouched at 1.20 Hz (saturation-freeze-driven policy property) - both evidence lines paid off, one per case.
Mechanism
A behavior appearing only on hardware has candidate causes on both sides of the sim2real boundary; changing training to fix it tests only one side per expensive cycle. Two cheap parallel probes - one intervening on the reward mechanism, one making sim reproduce the real behavior - localize the cause to a side before any training money is spent, and sim-reproduction of a real pathology is itself the strongest form of plant validation.
Applies when
- a gait pathology appears on hardware but never in any simulator
- deciding whether a sim2real gap is reward-side or plant-side
- tempted to change the gait clock/reward to chase a hardware symptom
“倍周期(真机 1.23~1.32 Hz ≈ 时钟一半,v6/v7 连续两代;sim 从不出现):两条证据线互为对照——(a)… 真机重跑看频率是否回 2.5 Hz(假说:v7 没有任何奖励把步态钉在时钟上,真机 plant 有 armature/摩擦、高频贵,自由滑落到复摆自然频率 ~1.1 Hz);(b)真机吊挂录 fit_actuator.py … 看能否在仿真里复现 1.25 Hz。谁先给出阳性结果谁定 v9 的方向。”
train/WALK_V8_SPEC.md § 9. 平行线 (倍周期) A walking policy's tilt cutoff is a legal state for a recovery policy - the default 45 deg fall guard had to be raised for recovery tests and is disabled once the switch owns falls, so the abort chain becomes the recovery timeout, the operator's cut, and the firmware torque limits
fall-guard-becomes-a-stateWhen a new skill makes a safety cutoff's trigger a legal state, replace the cutoff with a bound of the skill's own (a timeout ending in a safe stop) instead of just switching it off; keep the operator's cut and the firmware limits as independent layers, and write every flag change into the run sheet.
Symptom
deploy_policy's default protection stops the robot beyond 45 deg of tilt. A recovery policy starts lying at roughly 90-97 deg, so under the default it is refused on the spot - a flag the first hanging checklist forgot.
Context
The layers in the sources: deploy_policy's tilt cutoff (default 45 deg, a line in the safety chain); for standalone recovery tests the cutoff was raised (110 deg in the spec's A/B sheet; 181 deg, effectively off, in some runbook commands); with --recovery-policy the cutoff is disabled because a fall is now a state, not an exception, and RECOVERY lasting over 15 s ends in a safe stop (the runbook calls it the line where the spotter steps in). Independent of the policy: firmware torque limits checked at start (12/17/11 N*m, set_torque --check), the operator cutting enable at any kicking or oscillation, and in the one-leg teleop a space-bar stop that puts the foot down.
Change
The flag was added to the run sheets, and the FSM replaced the removed cutoff with its own bound (the timeout).
Outcome
The spec records the flag omission and its fix; it does not record the FSM's timeout being exercised on hardware.
Mechanism
A safety cutoff encodes one policy's notion of "abnormal"; a new skill whose normal operation lies beyond it either cannot run or runs with the cutoff off, and only a replacement bound keeps the chain closed.
Applies when
- deploying recovery, fall-damage or acrobatic skills behind existing safety checks
- a run sheet disables a protection flag
- listing the abort chain for a hardware session
“--max-tilt-deg(默认 45°,安全链第 13 行写的那个)。recovery 的合法状态覆盖整个倾角域,把它抬到 181 = 实效关闭 … RECOVERY 超时 15s 会自动安全停(看护介入线)”
RL系统/FOLLOW THIS copy 2.md § FSM 吊挂首测 ② 落地测 / #### Recovery Policy (operator runbook, undated)