Training Coach
Doctrine
A report may cite any of these as doctrine-N.
doctrine-1Contract freeze and fingerprint disciplineThe policy I/O contract (observation layout, scales, history semantics, action pipeline) is frozen and fingerprinted; every exported policy is stamped and verified; contract changes ship as new versioned profiles that leave old artifacts bit-identical, and old policies run forever under their era's pinned profile.
Case. The 215-dim omni contract was frozen with a three-machine digest; the one contract-level extension (lateral feed-forward) went in as a new `omni_ff` profile with the old profile provably untouched, and the contract checker caught two real wiring bugs before any training (`contract-freeze-and-checker`). A silently changed gait-clock default would have fed old policies a 25% slower clock - closed by pinned legacy profiles (`legacy-profile-pinning`). A stale derived USD forked plant mass 2.2% until an automated source-vs-derived instrument gated it (`derived-asset-staleness-check`). A gain profile is part of the closed loop a policy was trained in and belongs in its stamp; the recovery line's anchored authority was left out of its manifest and recorded as the gap not to repeat (`gain-profile-belongs-in-the-stamp`), and a second policy behind a deploy-side switch made the handoff state itself a contract (`recovery-two-policies-and-a-state-machine`, `walk-recovery-fsm-handoff`).
Coach application. On any proposal touching obs/action semantics, defaults, or derived assets: demand the version/profile plan, the fingerprint update, and the checker extension in the same change; flag any old artifact that would run under new defaults.
doctrine-2Attribution by resolved training params - never eval-override knobsCapability differences between lineages are explained only by digging each lineage's *resolved* training configuration and eliminating columns; evaluation-side override knobs (kd-scale, power-scale, cycle-time) act on the plant for *every* policy and may serve as deployment mitigations but never as explanations.
Case. Low-friction robustness across 8 lineages x 3840 cells was traced to kd DR *bandwidth* - every lineage had ground friction pinned to (1.0,1.0), so "trained friction" could not be the axis; the parameter axis and the plant axis were explicitly separated after the first attribution conflated them (`kd-bandwidth-mu-law-attribution`). "Weak turning" on hardware was a power-scale plant effect, not a training gap (`deploy-knob-attribution-before-retraining`); slowing the deploy clock was out-of-distribution, not a feature (`cycle-time-override-is-ood`). The ground truth for what a run trained under is the logged per-run config, not the source tree (`resolved-config-is-source-of-truth`).
Coach application. Whenever asked "why is lineage A better", require the resolved-param table first; kill zero-variance columns; refuse explanations phrased in eval-knob terms; when a knob helps, label it deployment mitigation.
doctrine-3PASS gates become constraints; FAIL gates become objectivesOnce a skill passes its gate, that gate converts into a standing regression constraint (budget <= 2/20 against the parent baseline) for all later training; gates currently failing are the only legitimate objectives of the next rung.
Case. The C ladder ran one frozen 13-cell x 20-seed matrix at every rung with promotion = "new skill PASS and old skills within regression budget"; C1 was stopped and re-rooted precisely because it trained away the root's backward PASS (`fixed-acceptance-matrix-per-rung`, `preregistered-stop-criteria-per-rung`). The C4 product shipped only at 260/260 cells with zero regression.
Coach application. Keep the ledger: every PASS adds a constraint row; propose rungs only against FAIL rows; treat any constraint violation as stop-and-attribute, never "the next rung might win it back".
doctrine-4One variable per ladder rung - counted against what the checkpoint sawA rung changes one variable, where "one" is counted against the checkpoint's actual training state, not against the current config's diff; batching is allowed only when each change owns a disjoint symptom space with a pre-registered ablation order.
Case. Two rungs failed identically because resuming s1e-500 under the evolved config silently added four plant variables the checkpoint had never seen ("单变量纪律不只看「我改了什么」,还要看「checkpoint 见过什么」" - `resume-state-dr-audit`). v8 legally batched four orthogonal fixes with a written ablation order (`orthogonal-batch-with-ablation-order`); v9 spent one run completing a 2x2 factorial so either outcome convicted a factor (`fill-the-missing-factorial-cell`); v10b's three-way ablation wrongfully convicted the clock and had to be retried fairly.
Coach application. Before any resume: diff cfg against the checkpoint's logged training state. Before any batch: require the symptom-ownership map and ablation order in writing.
doctrine-5Pre-register risks, readings, and stop criteria before the ladderBefore a ladder or risky rung, write down the known risks, the interpretation of every plausible outcome, and hit-any-one stop criteria - frozen before training, tightened when priors say results should come fast.
Case. The C ladder opened with three numbered risks including the exact falsification condition for its own root choice; A/B arms carried "预注册读法(事后不改)" tables; a level expected to fail was run anyway for its pre-registered diagnostic value (`preregister-risks-and-fork-readings`). Stop criteria caught C4-redo rungs at +200 instead of full caps (`preregistered-stop-criteria-per-rung`); hardware sessions pre-registered per-config expected signatures and the disagreement rule "不改结论改账" (`preregistered-real-expectations`, `feasibility-accounts-lock-design-point`).
Coach application. Refuse to open a rung without the written risk/reading/ stop block; after results, read conclusions off the pre-registered table and flag any post-hoc reinterpretation.
doctrine-6Plant parameters are measured, never inventedEvery plant number carries measurement provenance: armature = N^2 x rotor inertia from no-load tests, friction split by rig and by API column, torque limits shaped by per-joint gait peaks, latency traced through the real pipeline, masses weighed - and DR bands are additive around the measured nominal, sized to the measured dispersion.
Case. Guessed friction was 2.5x low and guessed damping 5x high (`friction-measured-not-guessed`); armature had been 0 with a 9:1 gearbox (81x reflected inertia, `armature-n2-rotor-inertia`); a uniform torque derating was "the wrong shape" vs measured peaks (`torque-limit-shape-by-measured-peaks`); the delay implementation itself was a wrong plant for a whole lineage (`latency-lerp-reverse-extrapolation`); the run design point was locked by three accounts including the tau_limit/kd speed ceiling (`feasibility-accounts-lock-design-point`); identified friction had to land in the right simulator API columns to act at all (`sim-api-friction-columns`). The recovery and one-leg lines opened with the same kind of accounts before any reward existed - a connected static path and the torque along it for an armless get-up, and the gains single support needs to be holdable at all (`get-up-feasibility-accounts-before-training`, `single-support-gain-authority-probe`).
Coach application. For any plant value in a config review, ask "measured how?"; reject absolute ranges with no nominal; check API column mapping and derived-asset regeneration whenever measured values land.
doctrine-7Sim2sim gate before sim2real - under deployment conditionsEvery checkpoint passes a second, independently built simulator before hardware, and both the gate and the smoke loop run under the measured deployment conditions (real pipeline delay, honest contact parameters, the deployment gain/power profile).
Case. The standing order "先sim2sim 再sim2real" (`sim2sim-gate-before-sim2real`); acceptance flipped to match hardware only under measured condim/torsional friction (`eval-plant-honesty-contact-params`); gates moved permanently to `--delay 2` after the kicking incident (`pipeline-latency-is-plant-not-dr`); and the harness itself must be audited - a frame-convention bug in the cross-sim evaluator invalidated a whole line of verdicts (`body-frame-velocity-api-audit`). The recovery line's second simulator caught a torque penalty paid for by bracing the legs together (`torque-penalty-bought-by-leg-bracing`), and a 1.8x torque disagreement between the two plants stayed binding because its one surviving explanation was never tested (`torque-disagreement-between-simulators-unresolved`).
Coach application. Block any hardware request lacking a second-sim PASS at deployment conditions; when sim2sim and training-side metrics disagree, treat the evaluator as a suspect too.
doctrine-8Observation honesty - the actor's inputs are a hardware contractThe actor observes only signals the real robot produces with realistic noise; privileged truths go to the critic; history windows are estimators and must train under plant variation; rewards on quantities the actor cannot observe buy only average suppression, never closed-loop correction.
Case. Ground-truth velocity/forces went critic-only (`observation-honesty-critic-only`); frame_hist under zero DR memorized the trainer's plant fingerprint - 0/20 transfer (`history-obs-needs-plant-variation`); world-frame yaw rewards could not teach pull-back because heading is unobservable to the actor - correction was routed to the deploy outer loop instead of breaking the contract (`reward-observability-limit`, `deploy-heading-loop-and-align-training`).
Coach application. Audit every actor-obs element for hardware existence; require minimal plant jitter whenever history/recurrence exists; for each reward, ask "can the actor see this error?" and route correction tasks to outer loops.
doctrine-9Reward economics are audited in realized currencyReward design decisions are made on realized per-step magnitudes under the actual policy and command distribution: price the do-nothing optimum before adding a mode, compare achieved values to the computed ignore-floor, calibrate thresholds between measured healthy and sick distributions, and ship every new penalty with a withdrawal clause.
Case. feet_air_time at weight 2.0 realized 0.038 vs tracking 1.2 - drag was rational (`realized-contribution-audit`); ignoring a vy command cost 28-180x less than ignoring vx until a gated tracking term was added (`reward-cost-of-ignoring-audit`, `gate-new-reward-terms-by-command`); achieved-vs-floor separated "never learned" from "priced out" (`ignore-floor-diagnosis`); the foot-distance wall was placed between measured healthy (0.6% tax) and sick (55%) policies (`calibrate-threshold-between-healthy-and-sick`); the landing penalty carried a pre-registered stand-down condition and actually stood down (`calibration-threshold-with-withdrawal-clause`); two clearance terms were inert until zero-points and gate occupancy were checked (`inert-reward-term-audit`). A get-up policy sat because three gated terms paid the seated pose 84% of the return and the one term that could tell sitting from standing was an exp kernel reading 4.6e-5 at the real error (`seated-basin-dead-exp-kernel`); a torque-tail term was weighted by its measured steady value beside a peer term after the estimate proved 12x off (`tail-torque-needs-hinge-on-computed-demand`).
Coach application. Never discuss weights in the abstract: demand the realized-contribution table, the ignore-floor number, and the healthy-pay calibration before any reward edit is approved.
doctrine-10The zero-cost option must be the desired behaviorFor every penalty, name what the zero-cost option is; penalize failure events (slip, saturation excess, contact in flight windows), never the motion or joints that healthy behavior uses; make degenerate strategies fatal via termination where penalties cannot price them out.
Case. Joint-usage penalties for drift taxed a 1.4%-of-momentum channel 2.7/step and collapsed training; the slip penalty costs a non-slipping gait exactly zero (`penalize-the-slip-not-the-joint`). A frozen-at-clamp joint pays zero action-rate forever - only a pre-clip saturation penalty flips the cheat economics (`saturation-cheating-zero-rate-cost`). Ungated phase shaping made standing 42x more expensive than stepping and cooked the hip motors (`moving-gate-42x-stand-tax`); crouch-shuffling lived until a height termination deleted it (`termination-closes-degenerate-basin`). A gated penalty is an exit: the policy parked just outside an uprightness gate, then just under a height gate, to stop paying a stance tax, and only a positive band plus an always-on guard closed both (`penalty-gate-is-an-escape-hatch`); a soft-limit penalty that charged the standing pose itself bought a 4.1 deg lean (`soft-limit-penalty-charges-nominal-pose`); an unpriced foot attitude was spent on edge-standing (`unpriced-foot-attitude-is-a-free-variable`); and the one-leg line listed its cheapest cheats before training and still met one through a zero-gradient band (`enumerate-cheapest-cheats-before-training`, `binary-band-reward-fake-touchdown`).
Coach application. Run the "零代价的选项是什么" audit on every proposed term; convert motion taxes into event-conditional penalties; check the termination set against each known degenerate strategy.
doctrine-11Measurement discipline: independent referees, signs, distributionsA disputed measurement is adjudicated only by an independent algorithm from raw state; directional ability requires sign-antisymmetry under command reversal; bimodal metrics are reported as mode shares (never medians, never 3 seeds); ratios are not comparable when totals change; reward values compare only within one command distribution; single chaotic events never cross machines.
Case. The triple reversal - a good metric was "refuted" by a sibling metric that shared the disease (`independent-referee-for-metric-disputes`, `body-frame-velocity-api-audit`); same-signed +/- responses were bias, not turning (`same-sign-response-is-yaw-bias`); the swing median sat in a bimodal gap (`median-hides-bimodal-distribution`); "v6 is jitterier" died on absolute energies (`ratio-metrics-need-absolute-check`); yaw gain measured 15x wrong in an oscillating frame (`heading-integral-not-body-rate`); a 44% improvement evaporated under same-distribution comparison (`same-distribution-reward-comparison`); drift direction was a limit cycle (`multiseed-sign-test-for-drift`); a cross-machine push cliff was chaos (`single-impulse-recovery-is-chaotic`).
Coach application. Before accepting any surprising number: ask for the independent recomputation, the sign pair, the distribution shape, and the comparison conditions. Retract in writing when a metric falls.
doctrine-12The deployment pipeline is plantIrreducible pipeline properties - action latency, rate limits, power/torque scaling, teleop command mappings - are part of the nominal plant, modeled from day one and reproduced in every gate; deploy-side scalings are crutches that flag unmodeled plant, and they cannot be algebraically folded into training constants.
Case. Right-leg kicking was over-trained-delay x loop gain; power 0.8 was a gain-reduction crutch that retired when the delay was modeled (`pipeline-latency-is-plant-not-dr`); power derating damages non-forward axes first (`power-scale-hurts-nonforward-axes`); training at 0.4 scale as the "twin" of deploying 0.5 x 0.8 collapsed 0/20 (`deploy-scaling-not-training-equivalent`); one shared teleop speed sent an out-of-band lateral command and the robot clipped its own foot (`teleop-command-band-per-axis`); the latency DR range had not even covered the measured pipeline (`latency-dr-covers-measured-pipeline`). A rate limiter added at deployment only clipped a policy that kept commanding (`deploy-rate-limiter-windup`); moved into training and anchored on the last command it became an integrator in the balance loop (`slew-anchor-is-an-integrator`); anchored on the measured angle it bounded torque and kept the bandwidth (`beta-anchored-action-target`). The walking lines' safe setting, power-scale 0.8, cut the ends of the recovery policy's full-range travel and left its spikes alone; a gain inside the trained band did the job (`power-derating-cuts-full-range-contract`).
Coach application. Demand the measured pipeline latency/limits in the plant model and in gate conditions; treat every deploy-side derating as a question ("what is this compensating?"); block per-axis command sources that exceed training bands.
doctrine-13DR budget is finite; its distribution is the measured supportRobustness is a conserved budget: disturbance training on an already-hardened lineage borrows from existing margins; DR ranges span the measured deployment support - no fictitious tails (they buy degenerate gaits), no single constants (they allow thin-margin specialization); harden the plant only after the task distribution is final.
Case. The same push dose helped a narrow lineage and damaged a balanced one - budget conservation (`push-dr-conditional-budget-conservation`); wide latency tails bought drag-glide, constant values shipped 60% thinner tilt margins - the answer is a narrow band on the measured support (`dr-tail-plant-continuation`, `constant-value-dr-overfits-margin`); task-first ordering because hardening a soon-to-change task wastes budget (`task-shaping-before-plant-hardening`); COM randomization used deliberately as a behavior-shaping tool, and rolled back on symptom per its own contract (`com-randomization-forces-leg-spread`, `com-dr-rollback-on-symptom`). DR that is switched on can still be thin: the run policy fell in the frontal plane its gain-and-latency randomization never touched (`thin-dr-judged-by-channel-coverage`), and a friction priority settled under one action contract had to be re-measured under the next (`friction-priority-re-measured-after-plant-change`).
Coach application. Before any DR rung: check the untrained policy against the spec, the lineage's current DR load, and the measured real-world range; after it: audit retained margins, not just the new tolerance.
doctrine-14Gates measure what hardware feels: posture, margins, stripped assistsAcceptance batteries carry posture-class rows (tilt max median, per-joint L/R asymmetry, temperature) beside task rows, graded margin columns beside binary gates, chirality scored per side, at least one condition that removes the environment's free stabilization, and validated predictive scalars promoted into the gate.
Case. Three same-shaped judging errors - survival, displacement, wz-difference - all missed what the operator felt; posture metrics had the predictive power (`task-metrics-vs-posture-metrics`, `stand-gate-posture-not-survival`); binary survival saturated and hid a 60% margin gap (`constant-value-dr-overfits-margin`); v5 passed everything on the ground and failed suspended (`suspension-probe-removes-free-stabilizer`); the hip_roll (l+r) scalar predicted real drift direction and ordering and entered the battery (`hip-roll-sum-predicts-lateral-drift`); averages hide chirality (`chirality-scored-separately`); gait-quality gates are judged at speeds that demand a gait (`low-speed-commands-reward-dragging`). The recovery line added the rest of the kit: where failed episodes end, not only where they started (`end-state-confusion-matrix`); a frozen acceptance distribution with a pinned seed (`frozen-acceptance-distribution-and-pinned-seed`); video of the metric rollout itself (`video-as-acceptance-record`); and the admission that a 10 s episode cannot see a stance that fails after a minute (`episode-length-bounds-what-a-gate-sees`). The one-leg line removed a foot-spacing wall that no gate measured, and the feet met on hardware (`removed-wall-returns-on-hardware`).
Coach application. Review every battery for posture rows, margin columns, per-side scoring, and an assist-stripped condition; when operator feel and gates disagree, suspect the metric class first.
doctrine-15Fork and root selection: recoverability, maturity, frozen rewardsChoose fork roots by which candidate's deficits the coming training can pay back (precision is recoverable; lost plasticity, symmetry, and margins are not); prefer mature checkpoints as roots even when younger ones score better as products; never fine-tune through a reward change - continuation is legal only with the reward frozen and plant/DR widening one rung at a time.
Case. s1e-500 beat higher-precision candidates because its exclusive strengths were unrecoverable (`fork-root-recoverable-shortfall`); the b300 arm proved maturity is capital against adaptation shock (`root-maturity-vs-product-quality`); the B-arm scatter/half-recover/collapse signature falsified reward-change fine-tuning and drew the legal boundary for S2 continuation (`fine-tune-reward-change-falsified`).
Coach application. For root debates, build the exclusive-strengths table and ask "which side can be trained back?"; require dual-arm evidence for maturity claims; classify any proposed continuation as reward-frozen or not before approving.
doctrine-16Curricula: verified engagement, lineage counters, disease-phase gatingAutomatic curricula must prove they engage (a saturated ratchet is constant DR wearing a curriculum's name); every ramp counts lineage-cumulative progress, not per-process steps; penalties aimed at late-stage pathologies ramp in after exploration noise decays; difficulty rises on measured per-stratum success, never on schedule.
Case. The s1f ratchet capped at iter 248 and never engaged (`auto-curriculum-engagement-check`); the saturation ramp re-fired at +600 after every resume and no shipped product ever saw the penalty (`curriculum-counter-lineage-steps`); the same penalty worked once gated to the disease phase and became an untouchable mechanism (`gate-penalties-to-the-disease-phase`); record-high aggregate reward hid a fully-failing delay stratum (`aggregate-metrics-mask-subgroup-failure`); bucket share is not a gradient lever (`bucket-share-is-not-a-gradient-lever`). An assist curriculum keyed to a pooled success share was withdrawn on the strength of the categories that already worked (`curriculum-criterion-conditioned-on-lagging-category`); a pace set by per-step income moved only when that income was time-gated (`per-step-income-drives-speed-time-gate`), and the same gate had to be retired in a lineage without the disease (`time-gate-vs-wide-stance-retire-the-fix`).
Coach application. Ask every curriculum three questions: does it engage (show the internal state)? what does it count (process or lineage)? when is it present (against the pathology's phase)? Check where shipped checkpoints sit relative to every ramp.
doctrine-17Probe before training: feasibility first, hypotheses in tablesAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop, enumerate hypotheses in a written table audited against actual configs cheapest-first, race one probe per side of the sim2real boundary for hardware-only pathologies, and use suspended tests to acquit or convict actuators before blaming authority.
Case. "在黑暗里试钥匙" - four sidewalk rungs failed until an open-loop probe separated exploration/waveform/authority in one experiment (`open-loop-probe-before-reward-tuning`); the foot-drag mystery fell to a seven-hypothesis config audit (`hypothesis-table-code-audit`); the period-doubling was resolved by racing a reward-side and a plant-side evidence line - and both paid off, one per sub-case (`period-doubling-evidence-race`); the suspended test acquitted the roll actuator in one measurement (`suspended-test-isolates-actuator-authority`). A read-only configuration probe told a wall from a slope in the recovery line's seated basin (`configuration-probe-wall-not-slope`), and the fix it pointed to - where the feet are - took prone from 0/159 to 158/159 (`prone-dead-end-is-foot-placement`); a knob that did not move its variable was recorded as no test of the idea (`dof-vel-penalty-is-not-a-pacing-knob`).
Coach application. When a skill resists training, prescribe the probe before any further reward edits; require verified target trajectories before imitation terms; keep a falsified-fixes list so closed roads stay closed (`amplitude-cut-falsified-yaw-fix`).
doctrine-18External advice is recomputed locally; values transfer as ratiosEvery external suggestion is classified adopt / already-have / modify / trap by recomputing its claim on the local reward table and probe data; numeric values transfer only as dimensionless ratios (to tracking weight, leg length, sqrt(gL), control rate); citations are verified to exist.
Case. "Start vy very small" would have destroyed sidewalk learning on this reward table - the gradient scales quadratically (`external-advice-audit-against-own-arithmetic`); swing-height targets and weights transferred correctly only through leg-length and tracking-ratio scaling (`transfer-ratios-not-absolutes`); the "6-step delay" was refused for lacking a control rate (`latency-dr-covers-measured-pipeline`); a borrowed reference's structure was FK-verified and its amplitude re-derived from the division of labor (`reference-structure-fk-amplitude-division`); retrieval agents fabricated verbatim arXiv quotes - only source-verifiable material was used; and one dismissed suggestion later proved right for a different mechanism, and was credited (`cycle-average-tracking-for-gait-quantities`). An advisor's staged state machine turned out to exist in none of the three papers it cited, and reading them changed the plan (`advisor-paraphrase-vs-paper`).
Coach application. Intercept every "paper X does Y" with the local recomputation; convert absolutes to ratios before comparison; verify quotes; revisit dismissed advice when new mechanisms appear.
doctrine-19Hardware sessions are scripted experiments, not tuning sessionsReal-robot time executes a pre-registered matrix: risk-ordered (baseline first, fragile last with a spotter), stage-gated (suspended smoke before ground), A/B sessions bracketed by a repeated reference run, operators briefed on measured zero-command and untrained-axis behavior, chirality-aware disturbance protocols, no field tuning - the only legal field changes are scripted, single-variable, and self-reversing.
Case. The S2 acceptance sheet (`risk-ordered-real-deployment`, `battery-bracketed-real-ab`, `know-zero-command-behavior`, `push-test-chirality-protocol`, `no-field-tuning-protocol`); the RAM-only torque experiment with automatic power-cycle rollback (`reversible-single-variable-field-experiments`); and the sim-veto rule - even sim's condemnations get one safeguarded hardware check when they judge the purpose-built configuration (`sim-veto-needs-real-confirmation`). The recovery line's first real run went ahead with its preconditions unmet and was stopped as dangerous (`first-real-get-up-violent-stage-one-policy`); after it: a staged hang, mat and floor protocol (`staged-hang-mat-floor-for-get-up`), a fixed power-cycle pre-flight and two-machine discipline (`power-cycle-preflight`, `two-machine-config-discipline`), a fall guard replaced rather than switched off (`fall-guard-becomes-a-state`), and logs that are part of the run (`hardware-log-is-the-attribution-input`).
Coach application. Turn every hardware request into a runbook with order, gates, brackets, briefing, and anomaly plays; refuse improvised parameter changes on the floor.
doctrine-20Close questions in writing; restart when the debt is structuralAudited questions get frozen verdicts with citable wording and an explicit reopening bar; hardware verdicts are dated by deployment-stack and calibration state and expire when those change; and when successive rungs shuffle symptoms without net progress, freeze the lineage as regression baselines, pay the structural debts, and retrain minimal - carrying laws and instruments, not weights.
Case. The chirality and COM questions were closed with frozen wording and "no reopening without new hard evidence" (`frozen-verdicts-semantic-boundaries`); v5/v6's condemnations expired with the deploy stack (`stale-verdicts-under-old-stack`); a 2-degree calibration fix moved the whole runnable envelope (`zero-offset-calibration-shifts-envelope`); plant upgrades are era boundaries with paired re-baselining (`plant-swap-invariants-vs-shifts`); and the 2026-08-05 reset froze v5-v11, fixed the latency FIFO / manifest / sampling / reward-table debts, and restarted - producing the lineage that reached hardware SOTA (`freeze-lineage-fix-structure-restart`, `minimal-reward-table-with-provenance`). The recovery line's real-robot verdicts ended up in three places that disagree, one of them an undated note in a command file (`write-hardware-verdicts-back`).
Coach application. Maintain the closed-questions ledger and quote it when symptoms recur; stamp verdicts with stack/calibration versions; when a team is three rungs into symptom-shuffling, raise the restart question explicitly with the freeze-fix-restart pattern.
doctrine-21Name the quantity in the space it lives inA goal, reward term or acceptance criterion about the feet, the base or the contact state is computed from the quantity itself - world poses, forces, per-category outcomes - never through a joint-angle, single-signal or pooled stand-in that assumes everything else sits at nominal; and every detector is validated on a behaviour known not to contain the event before it becomes a gate.
Case. The recovery line was caught three times: |ankle roll| as "flat feet" sold stance width and the real robot slid into the splits, a hip-roll criterion was confounded by 50 deg of yaw, and the joint table said 0.271 m where the feet were 0.159 m apart; task-space terms produced the first flat, wide stance (`joint-space-proxy-for-task-space-quantity`). Flight detection lied in both directions across two lines - foot height flagged 40% false flight on a walking gait, contact force alone flagged slip chatter as hops (`contact-detector-single-signal-lies`). A pooled height average described a robot that did not exist - six in ten standing, four in ten sitting (`zero-partial-credit-is-not-an-iteration-problem`) - and the walking line had learned the same lesson on yaw rate (`heading-integral-not-body-rate`).
Coach application. For every reward term and gate row, ask what physical quantity it stands for and whether it is measured directly; flag joint-space or single-signal stand-ins for task-space goals, ask for a detector validated on a negative control, and split pooled metrics by category before reading them.
doctrine-22Continuation needs a live gradient; a release is chosen by a scanContinue a converged policy only on a change that creates a live gradient, on a short budget, with every checkpoint scanned on the transfer axis; choose a release by running the full battery over a band of checkpoints and stop on signals, never by taking the last one; and when edits to the terminal phase cannot move a behaviour, roll back and retrain with the constraint present from the start, keeping the order in which the lineage acquired its mechanisms as explicit curriculum phases.
Case. A continuation with no new gradient drifted MuJoCo transfer from 100/98% to 80/28% while every Isaac gate stayed perfect, and a live-gradient continuation at the same depth kept it (`converged-continuation-is-poison`). One-leg checkpoints 100 iterations apart failed 1 and 38 of 40 cells, and late ones degraded (`checkpoint-choice-is-a-full-gate-scan`). Four in-lineage stance fixes failed because the stance was the end of the get-up path, and from scratch it grew right (`stance-decided-by-get-up-path`); fixes stacked on degraded states were rolled back by the user (`stop-stacking-roll-back-and-audit`); and the lineage's final recipe, trained from scratch in one run, sat at 0% because the order of its curriculum was part of the product (`curriculum-history-is-part-of-the-product`). The omni line's short adaptation budgets and mature roots are the same law seen from the other side (`continuation-budget-not-from-zero`, `root-maturity-vs-product-quality`).
Coach application. Before approving a continuation, ask for the new gradient, the budget and the transfer axis in the scan; before approving a release, ask for the scan; after three rungs without progress on the target, propose rolling back to the last good checkpoint and a from-scratch phase plan instead of a fourth patch.
Experience cards
165 cards matching “bucket-share-is-not-a-gradient-lever”.
The recovery line's real-robot verdicts live in three places that disagree - the spec's "fairly stable, first real stand-up" for v2_6, an undated runbook note that only v3_1p1c works, and a first run whose details were never recorded
write-hardware-verdicts-backA hardware verdict is a dated entry in the authoritative ledger - policy file and stamp, gain profile, floor, battery, tries, log file, what was seen - written back the same day; a note in a command file is a pointer, not a verdict, and a newer verdict that contradicts an older one must say so.
Symptom
Asked "which recovery policy works on the real robot", the sources give different answers, and none of them carries the conditions of the test.
Context
08-09: the first real run was stopped as violent and dangerous; which ONNX, which gain profile and whether a log existed were marked "to be recorded" and never were. 08-11: v2_6 was "fairly stable", the line's first real get-up, with splits after standing; v2_5b's result and both CSVs were "to be reported". 08-14: v3_1p1c was stamped and pushed, with "the real first test still needs the user present"; the spec records no hardware result for it. The operator runbook (undated) puts above the v2_6 and v2_5b floor commands the note that none of the recovery policies below work, only recovery_v3_1p1c - a verdict never written back into the spec, with no date, floor, battery, number of tries or log attached.
Change
None recorded in the sources; this card records the gap.
Outcome
The line's authoritative record ends with v3_1p1c as the product awaiting its first real test, while the operator's note implies it is the only one that works and that v2_6 (recorded as a success) does not.
Mechanism
Verdicts given at the robot travel by word of mouth and command-file comments; without a record carrying the conditions, a later reader cannot tell a changed verdict from a changed floor, battery or stack.
Conflicts
§43 (2026-08-11) records v2_6 as the first successful real get-up ("fairly stable"); the undated runbook says every recovery policy except recovery_v3_1p1c does not work; §49 (2026-08-14) says v3_1p1c's first real test was still pending. The runbook's claim has no date and was never written back to the spec, so it cannot be ordered against §43.
Applies when
- choosing which policy to deploy from an operator's notes
- a hardware session ends without a written result
- two documents disagree about what worked on the robot
“下面的recovery都不行 只有recovery_v3_1p1c.onnx”
RL系统/FOLLOW THIS copy 2.md § #### Recovery Policy (operator runbook, undated) Ideal PD is not enough - add a delay buffer and fit armature/friction/delay per joint
actuator-delay-buffer-fittingNever ship ideal PD to hardware: add a measured delay (in control steps) and per-joint armature/friction fitted from step and sine responses, and treat remaining actuator mismatch as your standing largest sim2real residual.
Symptom
Standard ideal PD actuator model transfers poorly; sim assumes targets take effect instantly and joints reach arbitrary acceleration.
Context
A developer with a successful on-hardware Isaac Lab biped modified the actuator model in two ways and calibrated it against the real robot: step-response plus sine-sweep tests (positive step, negative step, sine tracking), overlaying sim curves on measured curves and hand-tuning.
Change
(1) Delay buffer: action targets take effect after a uniform 6 time-step delay on all joints; (2) acceleration limiting so the actuator cannot reach arbitrary acceleration; (3) per-joint fit of armature / friction / delay - different joints genuinely needed different values.
Outcome
Hip joints fit worst, knee best; the developer rated the result "not perfect, the best I could do" and still listed actuator-model improvement as next work - i.e. even the fitted model remained the dominant residual.
Mechanism
Real actuation is a lagged, bandwidth-limited system; a delay buffer and acceleration cap are the two cheapest structures that reproduce its phase and magnitude response. Per-joint differences come from differing load, wiring, and friction states, so a single global constant underfits.
Applies when
- actuator model in sim is ideal PD with no delay
- step-response of real joint visibly lags or overshoots the sim's
- budgeting which sim2real gap to attack first
“标准 ideal PD actuator 不够用，他改了两处：延迟缓冲：目标不是立即生效，全部关节统一 6 个 time step 延迟 / 加速度曲线：执行器不能瞬间达到任意加速度 … 用 armature / friction / delay 三个参数逐关节拟合，标定方法是阶跃响应 + 正弦扫描 … 髋部关节偏差最大，膝关节最好。”
Experience.md § 执行器建模 —— 最值得抄的一条 (lines 50-59) A real-robot verdict is (policy x deployment stack) - when the stack changes materially, old verdicts expire
stale-verdicts-under-old-stackDate every hardware verdict with the deployment-stack version it was measured under; after any material stack change, re-test before trusting old condemnations or old praises - with the interpretation of each possible result written down first.
Symptom
walk_v5 stood condemned as "kicks wildly" and walk_v6 as "cannot walk unassisted" - but those verdicts were issued under an earlier deployment stack (--heading did not exist yet, several fixes had just landed); only v7 had ever run under the current unified stack.
Context
New sim evidence sharpened the doubt: a same-harness four-version sweep showed v6 was the HEALTHIEST archive at the real operating point (cmd 0.15: dominant frequency locked at 2.50, steps 35:35 perfectly symmetric, foot distance 203/190 mm best of four, mean tilt 4.2 deg, saturation 15%). A full re-test under the unified stack was scheduled with per-version questions and a pre-filled interpretation table ("判读表(预填假设,回来对号)"): e.g. v6 walks + frequency ~2.5 -> old verdict was the stack's fault, v6 becomes the comparison champion; v6 walks but at ~1.25 -> period-doubling on hardware = confirmed plant gap, actuator fitting promoted to mainline; v5 no longer kicks -> the kicking was an old-stack artifact.
Change
All four versions re-queued on hardware under one stack (same torque limits, slew profile, heading loop, logging), with the version-specific legacy profile pinned; verdicts held provisional until re-issued.
Outcome
The re-test design separated policy properties from stack artifacts before any policy was permanently written off - and turned each outcome into a specific conclusion via the pre-filled table.
Mechanism
A deployed behavior is produced by the policy plus everything between it and the motors (heading loop, slew limits, torque caps, clock); verdicts implicitly condition on that whole stack. Fixing the stack invalidates the conditioning, so old failures may be stack artifacts and old successes may not survive either.
Applies when
- deployment tooling (limits, filters, loops) changed since a policy was last judged
- deciding which historical policy is the rightful baseline
- a sim sweep contradicts an old hardware verdict
“只有 v7 在完整的今日部署栈下上过真机 … v5"左右乱踢"、v6"未能自主"的判决全部来自更早的栈(--heading 尚不存在, 部分修复刚落地)——判决已过期。且 2026-08-02 四代同机仿真横测翻出了新证据:v6 在真机工况(cmd 0.15)下是四代里最健康的仿真档案”
train/REAL_SWEEP_V5_V8.md § 0. 为什么重测 Two machines, one configuration - every gain, offset and torque limit changes only in robot.yaml, whoever edits pushes at once, both checkouts show the same commit before the robot moves, and a pulled policy file is size-checked and synced before power-off
two-machine-config-disciplineTreat the robot's configuration as a versioned artifact with one source of truth, push every change immediately, verify identical commits on every machine before a hardware session, keep hardware limits in the repo and the firmware in sync in both directions, and verify transferred model files (size, digest) before running them.
Symptom
The robot's onboard computer runs the bridge and deploy scripts from its own checkout while training and analysis happen on other machines; a hot fix left on one side, or a half-written file, silently makes the robot run something other than what was evaluated.
Context
The operator runbook's "wall version" of the two-machine discipline: configuration changes only in robot.yaml (calibration offset/sign, gains, torque limits), committed and pushed from the Mac, pulled on the robot, bridge restarted; code is not edited on the robot, and if it is, it is committed and pushed on the spot - nothing unpushed overnight; 30 seconds before every real-robot session both checkouts must show a clean status and the same last commit hash; changing tau_max requires writing the motor's limit_torque too (and the reverse); re-zeroed motors require re-measuring offsets. The recovery line added: after pulling on the robot, check the ONNX is not zero bytes (a lesson from a corruption incident on 08-12) and sync before cutting power; the recovery and main lines are separate worktrees, each pulled with --ff-only.
Change
Operating rules, pinned on the wall and repeated in the hanging checklists ("git pull, both machines on the same commit").
Outcome
The sources record the rules and the incident that produced the size check; they do not record a count of sessions the rules caught.
Mechanism
A policy is evaluated against one configuration; any divergence between the machines, or a truncated file, turns a hardware result into a result about an unknown configuration.
Applies when
- a robot's onboard computer and a workstation both hold the configuration
- someone hot-fixes code or gains on the robot
- model files are copied or pulled to the robot before a session
“改配置只改 robot.yaml(标定 offset/sign、增益、限扭全在里面)→ Mac git commit + push → NX git pull → 重启桥。 … 谁改完谁立刻推,永远不留未推送的改动过夜。 … 每次上真机前 30 秒检查:两边 git status 干净、git log -1 哈希一致。 … 铁律不变:改 tau_max 必须同步写电机 limit_torque(反之亦然);电机重新标零后 offset 必须重测回填 yaml。”
RL系统/FOLLOW THIS copy 2.md § ② 双机维护纪律(贴墙版) Pre-register the ladder's risks and how each future result will be read - before training
preregister-risks-and-fork-readingsBefore a training ladder or risky rung, write the risks, the stop rules, and how every plausible outcome will be interpreted - then do not edit them after seeing results.
Symptom
Without pre-registration, ladder results get rationalized after the fact; the team had already seen post-hoc reads go wrong and adopted written pre-commitment.
Context
The C-ladder execution sheet opens with three numbered pre-registered risks: (1) S2 plant robustness will not carry into omni - a full S2 redo is budgeted from the start; (2) the s1e recipe has a collapse valley at iter 1500+ (recorded twice), so every rung runs a watch_ckpt --every 100 smoke loop with stop-on-degradation; (3) the root's OOD survival edge may partly be "it is slower / commits less" - with the reading fixed in advance: if C1 training raises tracking while survival drops, the edge was bought with slowness, and root selection reopens. Later rungs went further, pre-registering a full result-to-conclusion table for the A/B arms ("预注册读法（事后不改）") and even pre-registering the author's own doubt that a level would fail and what its failure would prove.
Change
Standing practice: before each rung, write down (a) known risks with their mitigations, (b) the interpretation of each possible outcome, (c) stop criteria - all frozen before the run starts ("开训前写死，事后不许改").
Outcome
When arm-A/arm-B and redo results arrived, conclusions were read off the pre-registered table instead of argued; a predicted-likely-FAIL level (C4-redo3) was still run because its pre-registered value was eliminating the regularization hypothesis - which it did.
Mechanism
Pre-commitment converts each training run into a decisive experiment: outcomes falsify or confirm named hypotheses instead of being absorbed into a story; it also makes negative results valuable (a FAIL that eliminates a hypothesis advances the search).
Applies when
- launching a multi-rung training ladder
- running an A/B fork whose outcome will drive a fork/root decision
- a rung is expected to fail but is run for its diagnostic value
“三条预注册风险 … 若 C1 训后跟踪提上去而存活掉下来，说明这条优势是速度买的、不是通用性 → 那时重开选根。”
train/C_LADDER_RUN.md § 0. 三条预注册风险 Push DR helped one lineage and hurt another at the same dose - robustness budget is conserved and gets borrowed, not created
push-dr-conditional-budget-conservationBefore opening a disturbance-DR rung, measure whether the untrained policy already meets the spec; if training it anyway, expect the benefit to be conditional on the lineage's existing DR load, grade the intensity, and audit retained margins - budget spent elsewhere will be borrowed back.
Symptom
The push rung's outcome flipped with the lineage: direct +/-0.6 m/s push failed outright on first attempt (base walking collapsed - kd1.2 scan 0/3 from iter 3300, sim2sim self-falls with pushes OFF - no PASS point existed); staged +/-0.3 then gave the narrow-kd single-working-point lineage real gains (push survival 1/5 -> 4/5) while the SAME dose made the dual-working-point balanced-band lineage WORSE (20-seed survival 18 -> 12/20 plus across-the-board push regression).
Context
The four-ladder verdict ("四梯定案", s2e/s2f at both intensities) named the pattern: "push DR 收益条件性" - the benefit is conditional on how much robustness budget the lineage has already spent. The law candidate: "DR 总预算守恒, 平衡带鲁棒性从抗扰余量借" - total DR budget is conserved; a lineage already covering a wide plant band pays for push tolerance out of its disturbance margin. Both S2 ladders therefore closed at the friction rung, with the decisive numerator: untrained push tolerance already met the 4-6 N*s requirement, so the rung was not needed at all ("⑥ push 不训(收益条件性,免训 ±0.6 已达 标)"). The same accounting later justified the C-before-S2 ordering ("push/μ 两轮已实证 DR 预算有限且会被重分配") and trimmed the second S2 pass to three rungs.
Change
Push removed from the standing ladder; graded intensity retained as the method IF a lineage ever needs push training; "does the untrained policy already meet the disturbance spec" instituted as the first check before opening any disturbance rung.
Outcome
Two rungs (push, ground mu) deleted from the second S2 pass on measured grounds; the ladder's real yield was re-stated honestly as precision, not robustness (speed gate 0 -> 20/20, zero-command drift 0.98 -> 0.06 m, but push 159 -> 125/160).
Mechanism
A fixed-capacity policy allocates representation and margin across the training distribution; adding a disturbance axis to a lineage that already spans a wide plant family forces reallocation - the new tolerance is bought with existing margins. Lineages with narrow plant coverage have free budget, so the identical DR dose lands as gain. Benefit is a property of (dose x lineage state), never of the dose alone.
Applies when
- proposing push/perturbation training on a hardened lineage
- the same DR rung helped one lineage and hurt another
- accounting where a ladder's robustness gains actually came from
“push DR 收益条件性 —— s2e⑥a (单工作点血统 kd 窄带) ±0.3 得抗推 1/5→4/5; s2f⑥ (双工作点平衡带血统) 同档反而 20-seed 存活 18→12/20 且抗推全面倒退。规律候选: DR 总预算守恒, 平衡带鲁棒性从抗扰余量借。两阶梯均以 ⑤ 摩擦级收官 … 抗推 4~6 N·s 免训已达标。”
train/OMNI_V0_SPEC.md § 4. ⑥ push 四梯定案 (2026-08-07) A joint-velocity penalty meant to slow the get-up cut joint speed 16% and left the get-up time unchanged - the knob never moved the variable, so the idea it was meant to test stayed untested
dof-vel-penalty-is-not-a-pacing-knobBefore reading a result as a test of an idea, check that the knob actually moved the independent variable; velocity regularizers smooth a schedule they do not set, and a schedule driven by per-step task income moves only when that income's time structure does.
Symptom
The get-up took 0.6-0.9 s in Isaac with large torque demand; the user proposed getting up more slowly so less torque would be needed.
Context
The idea had support in the accounts: the acceptance bound is an upper bound of 5 s (5-8x margin), the quasi-static squat path peaks at 25% of the limits, and rolling over needs no momentum. R3.2 raised dof_vel from -1e-3 to -5e-3 as the single variable.
Change
dof_vel -1e-3 -> -5e-3 (child-run from R3.1).
Outcome
Get-up medians moved +0.02-0.04 s (noise); raw joint velocity -16%; torque demand median got worse (hip_pitch 46-48% -> 63-67%) as the new term competed with torque_headroom on the same joints; MuJoCo 98 -> 96%. Verdict FAIL on the knob, not on the idea, and the rung was not adopted. When pace was later attacked through the income's time structure (V2.5/V2.5b), the MuJoCo get-up moved into the 3.5-4.5 s design band.
Mechanism
The pace was set by base_height_progress paying for every step spent high (stand earlier, earn more); a velocity regularizer only smooths motion along the same schedule and does not change when the robot stands up.
Applies when
- trying to make a skill slower or gentler with smoothness penalties
- an experiment's primary metric did not move and a verdict is being written
- two penalties act on the same joints
“**关键判读:`dof_vel` 罚只把关节速度压了 16%,而起身用时一点没变。** 也就是说**这一级根本没有把"慢下来"这个自变量推动起来** —— 所以它**不构成对 用户假说的检验** … 起身节奏由 `base_height_progress` 的逐步计酬决定(早站起来就多 拿),速度正则只在同一条时间轨迹上把动作抹匀,不改变何时站起来。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §25 R3.2(dof_vel −1e-3→−5e-3,慢一点起身) A stand gate judged by survival passes a robot that wanders a meter - judge posture instead
stand-gate-posture-not-survivalFor every gate, ask what behavior the metric is a proxy for and validate its ordering against real observations; replace metrics whose ordering disagrees with reality, and demote them explicitly rather than silently.
Symptom
Real robot "standing" drifted 0.5-1.4 m across the floor while the sim stand gate scored a clean 20/20 - because the gate's metric was episode survival, which wandering does not violate.
Context
C2's stand condition was originally written as "survival regression <=2/20". A real-robot counter-example on 2026-08-08 forced the re-judgment: wandering robots survive. Cross-checking candidate sim metrics against real-robot feel showed max-tilt median ordering agreed with hands-on ranking, while displacement ordering was actually OPPOSITE to real impressions - so displacement was demoted to a reference quantity, not a gate.
Change
Stand PASS criterion rewritten from survival to posture: "stand tilt max median <= root baseline +1.5 deg"; displacement kept only as reference. Applied to all subsequent rungs (C4 and redo levels inherit it).
Outcome
Later rungs gated stand on tilt (e.g. C4 product: 7.7 deg vs parent 7.1 deg, +0.6 deg PASS); the wandering failure mode became visible to the battery instead of hidden by survival.
Mechanism
A gate metric is a proxy for an intended behavior; survival is a proxy for "did not fall", not "stood still". Metric choice must be validated against ground truth (real-robot feel/measurement), and a proxy whose ordering disagrees with reality on real data is worse than no metric - it steers selection backwards.
Applies when
- writing PASS conditions for stand/idle/hold behaviors
- a gate passes policies that visibly misbehave on hardware
- choosing between candidate metrics for an acceptance battery
“stand 必须用位姿判，不能用存活判（2026-08-08 真机反证改判）：站着乱走 0.5~1.4 m 时存活照样 20/20 —— C2 的 stand 条件原写「存活退化 ≤2/20」，选错了指标。改为: stand 倾角 max 中位 ≤ 根基线 +1.5°（倾角与真机手感排序一致；位移排序与真机相反，降为参考量）”
train/C_LADDER_RUN.md § 3b. PASS 条件 ⚠️ stand 必须用位姿判 A time gate that had cured one lineage's rushing made the from-scratch lineage trade away its stance width twice (0.364 -> 0.235 m, 0.355 -> 0.251 m) - its disease was absent there, so the fix was retired and the pre-gate checkpoint shipped
time-gate-vs-wide-stance-retire-the-fixCarry a fix into a new lineage only if its disease is present there; a mechanism that cured one lineage can be net negative in another, and when doubling a term's weight recovers almost nothing, treat the two objectives as structurally in conflict and remove the one whose purpose is gone.
Symptom
V3.1's phase 2 (the 3 s zero gate on standing income, continued from P1b) kept 100% success on every friction level and slowed the get-up, but the lateral stance drifted 0.364 -> 0.235 m and hip yaw crept to 57 deg against its 60 deg limit. With the width band's weight doubled (P2c, after P1c) it drifted again, 0.355 -> 0.251 m, below the pre-registered 0.30 m failure line.
Context
The zero gate had been introduced in V2.5/V2.5b to slow the old lineage's get-up. In V3.1 the rushing was already absent: P1c got up in 0.90-1.06 s with a worst torque ratio of 73.3%, better than the stamped v2_6c, because the full beta curriculum, second-difference smoothing and pull curriculum had cured the violence inside training.
Change
Recorded as a candidate law with two data points - the zero gate and a wide stance are mutually exclusive here - and the zero gate was removed from the V3.1 recipe. P1c (the pre-gate checkpoint) went through the full stamp-level acceptance instead.
Outcome
P1c passed everything: all six criteria, lateral stance 0.355 m, foot tilt P75 2.0 deg, mu {1.0, 0.8, 0.6, 0.4} x 10 seeds all 100%. recovery_v3_1p1c.onnx was stamped and pushed to the robot channel.
Mechanism
The zero gate moves the income toward "stay stable until the end", and under low-friction DR a wide stance has a slip tail, so survival outbids the width band; doubling the band's price bought back only 0.016 m - an auction that does not converge signals structural conflict, not an under-priced term.
Applies when
- porting reward mechanisms from an old lineage into a fresh recipe
- a width, margin or posture metric erodes during a late training phase
- a weight increase produces a negligible change in its target
“**定律候选(二实证):归零门 × 宽站互斥**。 … 加价翻倍只挽回 0.016,竞拍不收敛)。 … **归零门是 v2_5 血统的历史包袱,对 V3.1 配方是净负资产,P2 阶段除名 —— P1c 即终点形态**。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §49 终验(2026-08-14) A suspended (no-load) test acquits or convicts the actuator before you blame authority
suspended-test-isolates-actuator-authorityBefore attributing a failure to actuator authority, measure no-load tracking error and steady-state torque fraction; blame authority only if the task fails while the error grows with demanded force - and then fix gains or targets, not training.
Symptom
hip_roll sagged 0.21 rad on the ground and saturation questions loomed over the sidewalk plan - was the roll axis physically too weak (authority), or was something else limiting it?
Context
Before C4, the roll-authority question was settled by measurement triage: suspended test (--suspend, feet off ground) showed hip_roll tracking error 0.0008 rad - actuator acquitted; the entire 0.21 rad ground sag is load-induced. Steady-state torque was 25% of limit - 75% margin remains. Since sidewalk needs lateral force, not exact angles, authority was ruled "not a hard limit", with a pre-registered criterion for when it WOULD become one: sidewalk fails to track AND roll error keeps growing - then the fix is raising hip_roll kp or lowering the vy target, not more training.
Change
Hypothesis "roll authority insufficient" demoted from blocker to a monitored branch with an explicit trigger condition; C4 proceeded.
Outcome
Later open-loop probes confirmed the actuator could produce the behavior (sidewalk feed-forward ran at full amplitude, 5/5 survival), and the eventual C4 failure causes were measurement and reward, never authority.
Mechanism
Suspended vs loaded comparison separates the actuator's closed-loop competence from the load path: tiny no-load tracking error means the motor/controller is fine and any loaded deviation is statics (gravity / stiffness budget, kp trading error for force). Torque-fraction measurement then bounds how much force headroom actually remains.
Applies when
- suspecting an axis is "too weak" for a new skill
- large position sag on a loaded joint
- deciding between hardware fix, gain change, and more training
“吊挂（--suspend）实测 hip_roll 跟踪误差 0.0008 rad → 执行器无罪，地面下垂 0.21 rad 全是负载所致；稳态占限扭 25% → 仍有 75% 扭矩余量。… 判据：若 C4 出现「侧走跟不动且 roll 误差继续变大」，那才是权限账 … 解法是提 hip_roll 的 kp 或降 vy 目标，不是硬训。”
train/C_LADDER_RUN.md § 3d. roll 权限：已部分澄清，不是硬上限 Late training leaned on sampling noise as a stability crutch - deterministic play collapsed while training metrics stayed green
noise-crutch-deterministic-collapseEvaluate the deterministic policy in an external harness on a fixed cadence during training (not just at the end), select checkpoints on that curve, and treat a collapsing noise_std with rising training reward as a warning that noise is load-bearing.
Symptom
omni_s1's final checkpoint (model_5999) fell at 4 s even in Isaac's OWN deterministic play, while checkpoints from iter 1700-4000 were fine - and no training metric flagged anything. Policy noise_std had collapsed to 0.045 by iter ~990 (final 0.033).
Context
Diagnosis: the policy had learned to use its exploration noise as a dither/stabilizer - "策略把采样噪声当稳定拐杆,训练指标看不见" (the training metrics cannot see it, because training always runs with noise on). Countermeasures: entropy_coef 0.005 -> 0.01 to slow the std collapse, and - the structural fix - an in-training smoke loop (watch_ckpt.py): every 500 iters, export ONNX directly, run 3-seed MuJoCo evaluation, log CSV/TensorBoard curves plus three-view videos. The doctrine line was written in bold: "训练指标全绿不再是发育健康的 证据,冒烟曲线才是" - green training metrics are no longer evidence of healthy development; the smoke curve is. The follow-up run s1b showed the drift metric follow a U-shape (73 -> 8.6 at iter 3500 -> 76), making checkpoint selection BY the smoke curve (early stop at 3500) the shipping mechanism, with terminal re-degradation booked as known and unresolved.
Change
entropy floor raised; watch_ckpt smoke loop instituted as standing infrastructure; checkpoint selection moved from "last iteration" to "best point on the deterministic smoke curve".
Outcome
s1b shipped from iter 3500 (the U-bottom) instead of a degraded terminus; every later lineage (s1c/s1e, the C ladder's --every 100 loops) inherited the watcher as the standard guardrail.
Mechanism
PPO evaluates and improves the stochastic policy; if noise itself stabilizes the gait (dither smoothing a marginal limit cycle), the deterministic mean policy is a different, worse controller that training never measures. External deterministic evaluation on an independent simulator is the only readout of what will actually be deployed.
Applies when
- final checkpoints underperform mid-training ones
- noise_std collapses early while training reward climbs
- deciding which checkpoint to export and ship
“训练后期确定性脆化——noise_std iter~990 收到 0.045(终 0.033),model_5999 连 Isaac 确定性 play 都 4 s 摔(1700~4000 正常):策略把采样噪声当稳定拐杖,训练指标看不见。对策:entropy_coef 0.005→0.01 + train/watch_ckpt.py 训练中冒烟曲线 … 训练指标全绿不再是发育健康的证据,冒烟曲线才是。”
train/OMNI_V0_SPEC.md § 3. S1.1 修订记录 ② Drop the frozen policy into chosen configurations - a squat 2.7 cm lower than the stuck pose stood 52% of the time, the stuck W-sit 0%, and the interpolation between them showed a wall, not a slope
configuration-probe-wall-not-slopeWhen a policy is stuck, probe the frozen policy from a grid of hand-placed start configurations, including interpolations between the stuck state and a nearby state it escapes from; one read-only experiment separates height, torque, sampling and configuration and tells you whether to prevent entry or train the exit.
Symptom
After R0.3 the policy stood from 62% of starts and never from the W-sit it fell into; height, torque, missing samples and reward were all plausible suspects.
Context
A read-only probe placed the R0.3 policy directly into specified configurations. Squats (hip, knee, ankle) = (-.65,-1.3,-.65) stood 100%, (-1.0,-2.0,-1.0) 89.8%, (-1.2,-2.4,-1.2) at 0.176 m 52.3%; the measured W-sit at 0.203 m 0.0%; the account-(3) hand-over state (146 deg tilt) 34.4%; linear interpolations from the W-sit toward the squat at 25/50/75% stood 0.0/0.0/3.1%. The squat family's quasi-static torque is 16% of the limits, and the W-sit was visited ~9 s per episode in training. FK showed the squat family (-a,-2a,-a) keeps the torso vertical, the feet flat and the COM over the feet all the way from 0.146 m to 0.384 m.
Change
Height, torque and sampling were eliminated in one experiment; the next rungs targeted entering the W-sit (foot placement) instead of escaping it, and seeding the dead point itself was ruled out because it was already visited every episode.
Outcome
Pure configuration: the W-sit (hips externally rotated +/-47 deg, knees folded 110 deg, shins flat, feet beside the body) is a different place from the sagittal squat (feet flat under the COM). The policy's standing skill was bound to a narrow sagittal family, and the wall was confirmed by the interpolation. The foot-placement rungs that followed took prone from 0/159 to 158/159.
Mechanism
A learned skill covers the neighbourhood of the states it succeeded from; a start state outside that neighbourhood fails regardless of height or torque, and an interpolation that stays at zero until close to a working state shows the boundary is sharp.
Applies when
- a policy stalls in a specific posture and several causes are plausible
- deciding between reverse-curriculum seeding and entry-prevention shaping
- a feasibility account says a path exists but the policy does not take it
“**决定性对比:比死点矮 2.7 cm 的蹲姿站立 52.3%,死点 0.0%。** 所以不是高度、 不是力矩(蹲姿族准静态力矩膝 1.96/12、踝 1.24/17,只占 16%)、也不是训练采样 (死点每局被访问 ~9 s)。**是纯位形问题** … 插值实验进一步显示这**不是坡是墙** —— 走到 75% 仍只有 3.1%”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §15 死点位形实验(只读探针,同一个 R0.3 策略放进指定位形) A frame-history observation under zero DR memorizes the trainer's plant fingerprint - the estimator must see variation to learn estimation
history-obs-needs-plant-variationIf the observation carries history (stacked frames, RNN), keep at least minimal plant variation (gain/latency jitter) on from the first iteration - "nominal first, robust later" is structurally invalid for estimator-bearing contracts.
Symptom
omni_s1 (fresh 215-dim contract with a 5-frame history window, trained with DR fully off): training all green, yet the MuJoCo gate scored 0/20 on all eight doors - falls within 2 s, seven checkpoints, not one transferred.
Context
The history window exists precisely to let the actor implicitly estimate line velocity and actuator dynamics (the actor is denied base_lin_vel by observation honesty). Under a constant plant that implicit estimator has nothing to estimate - it learns the trainer's exact response fingerprint instead, and any other simulator's micro-differences are out-of-distribution: "5 帧窗按设计就是隐式估计器, plant 恒定时它学到 Isaac 精确响应的指纹". The planned "nominal-first-robust-later" staging was declared STRUCTURALLY incompatible with history observations: "估计器要见过变化才学估计, 否则学背诵" (an estimator must see variation to learn estimation, otherwise it learns recitation). Honest confound note kept: this is mixed with "zero DR does not transfer, period" - but both attributions prescribe the same fix, so no control was run.
Change
S1.1: minimum actuator jitter turned on from day one - kp/kd +/-10%, latency 0-1 frame (friction/COM/mass still nominal, no push - those stay for the S2 ladder).
Outcome
Transfer restored: survival 0/20 -> 20/20, speed 19/20, foot distance 20/20 (remaining failures moved to gait quality, a different disease); the staging doctrine was amended - history-carrying contracts never train under a frozen plant.
Mechanism
A recurrent/history channel fits whatever temporal structure minimizes loss; with a deterministic plant the cheapest structure is the plant's own impulse-response signature, yielding features that are simulator-specific rather than physics-general. Plant variation forces the channel to carry state-estimation features that transfer.
Conflicts
Attribution is explicitly confounded with the simpler "zero DR never transfers" reading ("与「零 DR 本身就不迁移」混杂 … 两种归因处方相同, 不做对照") - the source chose not to spend a control run separating them.
Applies when
- adding frame stacking or recurrence to an actor observation
- a nominal-plant policy fails a cross-simulator gate within seconds
- planning DR staging for a new contract
“frame_hist × 零 DR = plant 指纹过拟合——5 帧窗按设计就是隐式估计器, plant 恒定时它学到 Isaac 精确响应的指纹, MuJoCo 的微小差异即 OOD, 2 s 内摔, 七个 checkpoint 无一迁移。「先标称后鲁棒」的分段与历史观测结构性冲突:估计器要见过变化才学估计,否则学背诵。”
train/OMNI_V0_SPEC.md § 3. S1.1 修订记录 ① A reward on a quantity the actor cannot observe teaches "produce less of it", never "correct it" - closed-loop correction needs an outer loop
reward-observability-limitBefore adding a reward, check the actor can observe (or infer) the quantity: unobservable-error rewards buy only average suppression - route correction tasks to an outer loop whose commands stay in distribution, and do not break a frozen contract to add an observation a deploy-side loop can supply.
Symptom
Heading kept drifting despite world-frame yaw rewards, and a reviewer proposed heading-error rewards - raising the question of what yaw shaping can even teach this actor.
Context
The adopted architectural verdict: the actor's 45-dim base observation cannot see accumulated heading at all - projected_gravity is invariant to rotation about the gravity axis, and omega_z is a rate, not an angle. World-frame yaw-rate rewards are therefore privileged shaping that can only teach "少产生旋转" (generate less rotation), never "偏了以后拉回原线" (pull back to the line after drifting) - the policy cannot represent the error it would need to correct. The S1 gate (<=5 deg / 10 s) demands exactly the former, so the stack is right for its gate; active heading correction is assigned to the deployment outer loop (--heading P-loop converting heading error into in-distribution wz commands) plus small-wz training - and the 215-dim contract is explicitly NOT extended with a heading observation ("契约不加 heading 观测,冻结不动"). The reviewer's companion bias hypothesis was adjudicated with data: drift is bimodal - a basin mechanism decides whether you leave (seeds vary +/-16-46 deg vs -385 to -391 deg), and once out, rotation direction is constant (weight chirality; candidate root: the phase clock always swings left first).
Change
Yaw shaping kept as rate-tracking (three-layer stack); heading correction owned by the deploy outer loop; contract frozen; the "which behaviors need an outer loop" question settled by observability analysis rather than reward tuning.
Outcome
Stopped a contract change and a futile reward direction; drift work split correctly into rate-suppression (trainable) and error correction (outer loop), consistent with the earlier measured 10x drift reduction from the deploy-side loop.
Mechanism
A policy can only condition on its observation sigma-algebra; rewards on functions outside it shift the marginal action distribution (open-loop average effects) but cannot create feedback on the unobserved variable. Whether to add an observation, an outer loop, or accept average-shaping is decided by the task's gate: suppression gates need shaping, correction gates need the variable in some loop's view.
Applies when
- adding rewards on accumulated/世界-frame quantities (heading, position)
- deciding between a new observation, an outer loop, and shaping
- a drift symptom persists across reward-weight changes
“actor 的 45 维基座观测不到累计航向(projected_gravity 对绕重力轴旋转不变,ωz 是速率不是角度)——世界系 yaw 奖励是特权塑形,只能教「少产生旋转」,不能教「偏了以后拉回原线」。… 主动纠偏闭环 = S3 把小 wz 进分布 + deploy --heading 外环 … 215 契约不加 heading 观测,冻结不动。”
train/OMNI_V0_SPEC.md § 3. 评审④判决(2026-08-06,S1.3 开训前) Bracket a real-robot A/B with a repeated reference run - battery drain is the confound
battery-bracketed-real-abOrder hardware A/B sessions as A-B-A: repeat the first condition at the end, and void the comparison if the bracket runs disagree - never let battery or venue drift ride on the second condition.
Symptom
In a two-policy teleop A/B on hardware, the second policy is measured on a lower battery voltage than the first - a systematic bias that would be read as a policy difference.
Context
C2 real A/B (checkpoint 700 vs A800, same floor, same day) was scripted as 700 -> A800 -> 700-rerun, with the explicit note that a teleop session drains the pack and the trailing policy "naturally suffers".
Change
Protocol: run the reference policy first AND last; if the two reference runs differ noticeably, declare the whole session battery/floor-polluted and void the A/B ("结论作废重来"). Also log electricity per run.
Outcome
Called out as the round's only systematic confound, closed by one extra command ("这是本轮唯一的系统性混淆源，一条命令就能堵掉").
Mechanism
Battery voltage scales available torque, and torque loss hits behavior asymmetrically (see power-scale-hurts-nonforward-axes), so drain masquerades as policy regression; a head/tail reference pair converts the unobserved drift into a measured control.
Applies when
- comparing two policies or settings on hardware in one session
- any sequential hardware evaluation where the plant drifts (battery, temperature, floor wear)
“为什么要 700 复跑：一次遥控 session 下来电池会掉压，第二枚天然吃亏。头尾各跑一次 700，若两次 700 明显不同，说明这轮 A/B 被电量污染，结论作废重来。这是本轮唯一的系统性混淆源，一条命令就能堵掉。”
train/C_LADDER_RUN.md § 3c. A-3 真机 A/B（同一段地板、同一天、电量记账） When the eval proxy has a known systematic bias, gate on within-proxy differences, not absolutes
relative-metrics-survive-proxy-biasWhere the evaluator is known-biased, design gates as within-evaluator contrasts (left vs right, A vs B, pre vs post) that cancel common-mode error; reserve absolute thresholds for quantities whose proxy calibration has been checked.
Symptom
MuJoCo systematically overestimated yaw turn gain (1.58/2.45 where Isaac measured 1.04/1.02), and friction alignment recovered only part of the gap (mu 1.0 -> 0.6 pulled it to 1.43/2.27) - so any absolute turn-gain acceptance threshold in MuJoCo would be judging the proxy's bias, not the policy.
Context
The acceptance criterion was rewritten to use only the left/right difference of the turn gain (standard: <20%): both directions pass through the same biased proxy, so the bias largely cancels in the difference while the policy's chirality - the thing being gated - survives. The absolute-gain row was dropped: "转向只判左右差,不判绝对值". A parallel task was still opened to align MuJoCo contact parameters to Isaac's (mu, restitution), since drift proved highly friction-sensitive (straight-line drift -65 deg at mu 1.0 vs +1 deg at mu 0.4) - bias reduction and bias-robust metrics proceeded together.
Change
Gate metric changed from absolute turn gain to left-right gain difference; proxy-alignment work scheduled separately rather than blocking acceptance.
Outcome
Turn acceptance became meaningful across proxy versions (v5 70% -> v6 19% difference measured the real improvement) while the absolute bias question was pursued without holding the ladder hostage.
Mechanism
A systematic multiplicative or additive proxy bias applies to both arms of a mirrored measurement; differencing (or ratioing) mirrored conditions cancels the common-mode bias to first order, leaving the asymmetry signal. Metrics built this way remain valid while the proxy is imperfect - which it always is somewhere.
Applies when
- a sim proxy disagrees with the trainer or hardware in absolute terms
- writing acceptance thresholds for direction-paired skills
- proxy calibration work would otherwise block a ladder
“转向只判左右差,不判绝对值 —— MuJoCo 的偏航增益系统性高估(实测 1.58/2.45 vs Isaac 1.04/1.02),摩擦只能解释一部分(μ 1.0→0.6 仅拉到 1.43/2.27)。差值是相对量。”
train/WALK_V5_SPEC.md § 6. 验收 Cross-simulator gate (Isaac Lab to MuJoCo) comes before any hardware attempt
sim2sim-gate-before-sim2realGate every policy through a second simulator with an independently built plant before hardware; treat sim2sim failure as a contract or overfitting bug, and sim2real failure after a sim2sim pass as a plant/actuator gap.
Symptom
A policy that only ever ran in its training simulator carries untested dependencies on that simulator's solver, contact model, and defaults; the first place those dependencies surface should not be the real robot.
Context
Standing order of operations for the whole Lucen program, recorded as the opening line of the experience log: train in Isaac Lab, gate in MuJoCo, only then go to hardware. The MuJoCo side is the same plant used for evaluation batteries, so a sim2sim pass also validates the exported policy + contract (obs ordering, scales, defaults) outside the training stack.
Change
Pipeline rule adopted - every checkpoint must pass the MuJoCo evaluation battery (sim2sim) before it is considered for real deployment (sim2real).
Outcome
Used generation after generation as the cheap filter; hardware sessions only ever received policies that had already survived a second simulator.
Mechanism
Two simulators disagree exactly where a policy is overfit to simulator-specific artifacts (contact softness, integrator, default parameters, obs conventions); a cross-sim transfer catches contract bugs and solver overfitting at zero hardware risk, so real-robot failures that remain are attributable to genuine plant/actuator gaps.
Applies when
- planning the path from training to first hardware trial
- exported policy behaves differently outside the training framework
- triaging whether a real-robot failure is contract vs plant
“先sim2sim - 从isaaclab 到mujoco / 再sim2real”
Experience.md § opening lines (1-2) A curriculum ramp keyed to the process step counter re-fires on every resume - and shipped policies never saw the penalty
curriculum-counter-lineage-stepsKey every curriculum/ramp schedule to lineage-cumulative progress, not per-process counters; and audit where your shipped checkpoints sit relative to every ramp - a penalty that no product ever experienced is not part of your training.
Symptom
vx+0.30 died at a fixed relative time in every resumed run: resume at 500 -> slide at 1100, zero at 1300; resume at 700 -> slide at 1300, zero at 1500 - absolute depths offset by exactly the resume offset, relative timetable identical.
Context
ramp_reward_weight (the saturation penalty ramp) read env.common_step_counter, which restarts at 0 for every run including --resume. So start_step=600 meant "600 iters after THIS resume", not "lineage iteration 600". The A/B arm pair was the clean proof: their env.yaml differed only in log_dir, only resume point distinguished them, and the omni CurriculumManager had exactly one active term - nothing else could produce that timetable. Second consequence: every shipped checkpoint (s1e-500 at +500, C2-700 at +200, A800 at +100) was selected before its run's +600, so the saturation penalty weight was 0.000 for every product ever shipped - explaining saturation 33% and raw |action| 1.9 against clip 1.0 (hip_roll in bang-bang), i.e. half the heat budget.
Change
Two independent recommendations recorded: (1) make the ramp count lineage steps (add the checkpoint's iteration offset on resume) or pin terminal weights in downstream rungs instead of ramping; (2) give the saturation penalty its own rung - never mixed into a skill-learning rung (that would be two variables again).
Outcome
Explained the recurring +600 death of the highest-amplitude command and the persistent actuator saturation of all shipped products with one root cause; honest caveat booked (at +800 the weight is only -0.086, small, but vx+0.30 is the command demanding the largest action amplitude, so it is squeezed first).
Mechanism
Resumable training splits "the lineage" from "the process"; any schedule keyed to process-local counters silently re-applies its transient to every descendant run, and any product-selection habit that picks checkpoints early systematically samples the pre-ramp regime - the curriculum exists in the config but never in any shipped policy.
Applies when
- resumed/forked training with any scheduled reward or DR ramp
- a metric dies at a fixed offset after each resume
- shipped policies show behavior a late-schedule penalty should prevent
“ramp_reward_weight 读的是 env.common_step_counter，它每个 run 从 0 开始，--resume 也不例外。… 原始 run / 臂B | 500 | 1100 = +600 | 1300 = +800；臂A | 700 | 1300 = +600 | 1500 = +800 … 所有出品其实从没见过饱和罚。… 这解释了 sat_max_pct 33%、raw |a| 最大 1.9（clip 是 1.0）—— hip_roll 一直在 bang-bang，而罚它的那一项权重恒 0。热账的一半在这里。”
train/C_LADDER_RUN.md § 3g. 系统性问题：saturation_ramp 每次 resume 归零 Ungated phase shaping made standing 42x more expensive than stepping - and the stepping was cooking the hip motors
moving-gate-42x-stand-taxGate every phase/clock-driven shaping term on the command that justifies motion, price the cmd=0 case explicitly during design - and when a reward flaw is sim-only, book it with trigger conditions instead of operating immediately on a working lineage.
Symptom
At cmd = 0 the sim policy never stood still - it stepped in place and crept 0.98 m per 20 s; on the real robot the same lineage's stepping made hip_roll motors run 20 degC hotter than every other joint (43-48 degC vs 25-28).
Context
The arithmetic closed it: the three phase-shaping terms (joint_pos_ref 1.6, feet_contact_number 1.2, feet_clearance_swing 1.6) are driven by the gait clock with NO command gating, so standing at cmd=0 forfeits 3.32/step of shaping while honest standing earns only 0.078 of tracking - stepping wins 42x. The heat chain: perpetual stepping = perpetual single support = one hip_roll stalled at ~4.3 N*m (25% of torque limit) carrying the torso's frontal-plane moment - two hip_rolls = 90% of whole-machine steady-state I2R; measured stand-vs-step comparison: total heat -71% when actually standing. The suspended test acquitted the actuator (0.21 rad sag -> 0.0008 rad in air) and mechanics vetoed the easy fix ("降 kp 救不了热" - equilibrium torque equals the external load regardless of kp). The fix (moving_gate: hard-gate the three shaping terms on |cmd| > eps) was designed - then DEFERRED by the user because the real robot at the time stood fine: "真机不表现该问题, 为真机不存在的病改奖励表不划算", with written trigger conditions (C-ladder stand row persistently failing, or real robot starting to step/drift at cmd=0) and the known hazard tag (this is exactly the reward-change class that triggers the B-arm signature). When the real robot later DID step and cook, the booked trigger fired and moving_gate moved from debt to to-do with its benefit re-priced: "停止空烧 hip_roll,稳态发热降 ~71%".
Change
moving_gate designed with the gate_by_cmd convention; deferral, triggers, and expected heat recovery all pre-registered instead of patching the reward for a then-sim-only symptom.
Outcome
The cmd=0 stepping went from mystery to closed arithmetic; the thermal measurement (hip_roll +20 degC) quantitatively confirmed the 90%-of-heat prediction; the reward change waited for real-world justification instead of spending a risky revision early.
Mechanism
Clock-driven shaping terms define a perpetual-motion bounty unless gated by command; the resulting idle gait is not a training bug but the table's optimum. Its cost surfaces on hardware as stall-torque heating set by statics (mass x lateral offset), which no gain change can remove - only removing the motion (gating) or widening the stance can.
Applies when
- the policy steps in place or creeps at zero command
- specific joints run hot in idle behaviors
- deciding when a known reward flaw justifies a risky mid-lineage fix
“塑形合计 −3.32/步 … 净: 站定亏 42 倍 … 两颗 hip_roll 4.29 / 4.09 N·m(各占限扭 25%),占全机稳态 I²R 的 90% … 吊挂实测 hip_roll 跟踪误差 0.21 rad → 0.0008 rad … 降 kp 救不了热 … 真机不表现该问题, 为真机不存在的病改奖励表不划算”
train/README.md § C1 FAIL 节 (cmd=0 的 sim/真机分歧记账) / C2 真机 A/B 三b 发热定性 A soft joint-limit penalty charged the standing pose itself - the geometric-zero knee sat on its hard limit, so stand_v1 bent its knees to dodge 0.419 per step and leaned 4.1 deg forward; excluding the knee gave 0.24 deg
soft-limit-penalty-charges-nominal-poseBefore training, evaluate every penalty at the nominal pose; if a joint's soft limit sits inside the pose the task requires (a straight knee on its hard stop), exclude that joint from the soft-limit penalty and let the action clip enforce the hard limit.
Symptom
stand_v1 (retrained after the default pose moved to the CAD geometric zero and mirror augmentation was added) fixed left/right asymmetry (6.8 -> 0.0 deg) but settled at a 4.1 deg forward lean, where pure PD at the same default settled at 0.1 deg - the policy was actively pushing itself forward, which is exactly the real robot's failure direction.
Context
soft_joint_pos_limit_factor = 0.9 shrank the knee's soft limit to -/+0.1047 rad, while the geometric-zero default has the knee at q = 0, exactly on the hard limit. Standing in the nominal pose therefore paid 0.2094 x 2.0 = 0.419 per step in dof_pos_limits (alive earned only 0.5). The policy's way out was to bend the knees to -/+0.1013 rad, and the cost was the forward lean.
Change
stand_v1b: the knees excluded from dof_pos_limits (a straight knee IS the standing pose; the hard limit is still enforced by the action clip). No other change.
Outcome
stand_v1b: max tilt 0.3 deg, steady tilt 0.24 deg, asymmetry 0.1 deg, height 0.384 m - exactly nominal - with knees at -0.0007 / +0.0005 rad. It became the standing release used on the real robot, and later the standing side of the recovery switch. The same exclusion was carried into the recovery contract (knee at the clip in the standing pose) and the one-leg reward table.
Mechanism
A limit penalty whose soft boundary lies inside the nominal pose turns the nominal into a taxed state, and the policy buys its way out with whatever posture change is cheapest - here a knee bend paid for with lean.
Applies when
- a standing or default pose has a joint at or near its hard limit
- a policy settles in a small steady tilt that pure PD does not show
- soft-limit factors shrink limits uniformly across joints
“`soft_joint_pos_limit_factor=0.9` 把膝软限位内缩到 ∓0.1047,而几何零位 default **膝盖 q=0 正好压在硬限位上** ⇒ 站在标称姿态每步白扣 `0.2094 × 2.0 = 0.419` (alive 才 +0.5)。策略只能屈膝到 ∓0.1013 躲罚,代价是躯干前倾 —— 恰好是真机的 失效方向。 … 修掉"软限位罚标称姿态"后重训(`dof_pos_limits` 排除膝盖)。**前倾问题彻底消失** … 不再屈膝躲惩罚,高度正好落回标称 0.3840。”
train/README.md § 三期: 镜像对称增强 + 站立 v1 (2026-07-28) / stand_v1b (2026-07-28): 站立定版 Three same-shaped judging errors - task metrics (survival, tracking, displacement) cannot stand in for posture metrics
task-metrics-vs-posture-metricsKeep validated posture-class rows (tilt, per-joint L/R asymmetry, temperature) in every acceptance battery alongside task rows; when operator feel contradicts the gates, suspect the metric class before the operator - and never build a new skill on what is actually an asymmetry defect.
Symptom
The C2 product judged "full pass" on task metrics (A800: turn-gap 7 pp, vx+0.30 19/20) felt WORSE in the operator's hands than the half-pass 700: A800 tilted up to 12.90 deg (700: 6.64), drifted left while standing, showed larger per-joint asymmetries, and ran its hip_rolls 5 degC hotter.
Context
The re-judgment catalogued three same-type metric errors in one campaign: (1) stand judged by SURVIVAL - missed 0.5-1.4 m wandering; (2) stand ranked by DISPLACEMENT - ordering was opposite to real feel (tilt ordering matched); (3) chirality judged by wz-tracking GAP - measured turning symmetry while the robot's actual disease was postural left/right asymmetry, "两个不同的东西,且结论相反". Common pattern named: "我一直用「任务指标」当判据,而真机手感对应的是「姿态 指标」… 任务类指标不能替代它". The fix was already in the data: the per-joint left/right asymmetry table (printed identically by sim2sim and deploy) agreed with hardware in direction on every row - "判据可用、有预测力,我只是没把它写进 PASS 条件". Shipping decision followed the posture read: product reverted to 700 ("又一次「买到 精度、卖掉别的」"), and the C4 root moved to 700 as well, with the sharpest line of the episode: A800's left-drift "like sidewalking" is probably its frontal-plane asymmetry defect, not a capability - "在缺陷上建能力是危险的".
Change
Two posture quantities with demonstrated real-robot predictive power promoted into every PASS battery: tilt-max median and per-joint left/right asymmetry (both sim-computable, deploy-homologous); motor-temperature readout added to session close-out.
Outcome
Deployment flipped to the posture-better checkpoint; the hip_roll temperature table (43-48 degC vs 25-28) confirmed the earlier 90%-of-heat account; the run-line acceptance battery inherited the posture rows from birth ("任务类替代不了姿态类").
Mechanism
Task metrics measure goal attainment under the evaluator's episode definition; posture metrics measure the body state trajectory that operators, motors, and downstream skills actually experience. The two can rank candidates oppositely because task success tolerates postural pathology - so a battery without posture rows is blind to exactly what hardware feel reports first.
Applies when
- hardware feel disagrees with a green acceptance table
- choosing between checkpoints that split task vs posture metrics
- selecting the root for a skill that resembles an existing defect
“共同模式:我一直用「任务指标」(存活 / 跟踪率 / 位移)当判据,而真机手感对应的是「姿态指标」(倾角、逐关节左右不对称)。→ 验收判据里必须有姿态类指标,任务类指标不能替代它。… A800 的「左飘像 side walk」很可能 … 是它更大的额平面不对称的表现 —— 在缺陷上建能力是危险的。”
train/README.md § C2 选点改判 (2026-08-09): 手性判据第三次选错指标 Privileged signals (true velocity, foot force, foot height) go to the critic only
observation-honesty-critic-onlyTreat the actor observation vector as a hardware contract: every element must exist on the real robot with realistic noise; privileged simulator truths belong in the critic only.
Symptom
Policies trained on ground-truth base linear velocity work in sim and fail on hardware, where only a drifting IMU and encoders exist - the policy has learned to depend on a signal that does not survive deployment.
Context
Many open-source locomotion stacks feed simulator ground-truth linear velocity to the actor. The reference team refused: the real robot has no ground-truth velocity. Asymmetric actor-critic keeps the training benefit of privileged information without deploying the dependency.
Change
Route ground-truth velocity, foot contact forces, and foot heights to the critic only; the actor observes exclusively signals that exist on hardware (IMU-derived quantities, encoders, commands, previous actions).
Outcome
Recorded as adopted doctrine in Lucen's experience log; the trained actor's input contract matches what the real robot can actually produce.
Mechanism
The critic is discarded at deployment, so it may consume any privileged state to reduce value-estimation variance; the actor's observation set is a deployment contract - anything in it that hardware cannot supply (or supplies with different noise/drift) becomes a train/deploy distribution shift the policy was never trained to handle.
Applies when
- designing actor/critic observation spaces
- reviewing a config where the actor sees base_lin_vel or contact forces
- sim policy is strong but real robot drifts, oscillates, or falls without obvious actuator cause
“很多开源代码库把真值线速度喂给策略，Asimov 团队没有，因为真机上没有真值速度，只有会漂的 IMU 和编码器；用完美速度训练出来的策略会依赖它，然后在硬件上失效。真值速度、足底力、足高统统只给 critic”
Experience.md § 观测空间的诚实性 (line 7) Real robot walked at half the sim clock for two generations - resolved by racing a reward-side and a plant-side evidence line, not by guessing
period-doubling-evidence-raceFor a hardware-only pathology, refuse to guess: pre-register one probe per side of the sim2real boundary (can the reward mechanism change it on hardware? can fitted plant parameters reproduce it in sim?) and let the first positive result direct the next version.
Symptom
The number-one sim2real gap: on hardware v6/v7 stepped at 1.23-1.32 Hz - almost exactly half the 2.50 Hz gait clock they were trained and simulated at; sim never reproduced it, two generations running.
Context
Instead of committing training budget to a guess, v8 pre-registered two mutually controlled evidence lines and kept the clock OUT of the training variables: (a) reward-side - if the v8 saturation fix revives joint_pos_ref (the term that pins the gait to the clock), re-run hardware and see whether frequency returns to 2.5 Hz (hypothesis: v7's frozen actions meant NO reward was pinning the gait to the clock, and the real plant - with armature and friction making high frequencies expensive - slid down to the leg's pendulum natural frequency ~1.1 Hz); (b) plant-side - record suspended joint data (fit_actuator), fit armature/friction, load the fitted values into sim2sim and see whether the 1.25 Hz reproduces IN SIM. Decision rule fixed in advance: "谁先给出阳性结果谁定 v9 的方向 (奖励侧 vs plant 侧)" - whichever line goes positive first sets the next version's direction.
Change
Period-doubling excluded from the v8 change set; both diagnostic lines scheduled in parallel as non-blocking work; frequency reported factually in acceptance with no pass/fail attached ("倍周期是否消失 不设判定,它是 §9 的关键证据").
Outcome
The gap was routed into a decisive-experiment structure rather than a speculative retrain; the plant-side line pointed at exactly the unmodeled armature/friction that were later measured and installed as the plant baseline. Resolution (era-2c full-plant retest): the family had TWO causes - v8's low-speed period-doubling vanished once measured armature+friction were installed (1.30 -> 2.50 Hz, bifurcation-edge machine sensitivity), while v7's stood untouched at 1.20 Hz (saturation-freeze-driven policy property) - both evidence lines paid off, one per case.
Mechanism
A behavior appearing only on hardware has candidate causes on both sides of the sim2real boundary; changing training to fix it tests only one side per expensive cycle. Two cheap parallel probes - one intervening on the reward mechanism, one making sim reproduce the real behavior - localize the cause to a side before any training money is spent, and sim-reproduction of a real pathology is itself the strongest form of plant validation.
Applies when
- a gait pathology appears on hardware but never in any simulator
- deciding whether a sim2real gap is reward-side or plant-side
- tempted to change the gait clock/reward to chase a hardware symptom
“倍周期(真机 1.23~1.32 Hz ≈ 时钟一半,v6/v7 连续两代;sim 从不出现):两条证据线互为对照——(a)… 真机重跑看频率是否回 2.5 Hz(假说:v7 没有任何奖励把步态钉在时钟上,真机 plant 有 armature/摩擦、高频贵,自由滑落到复摆自然频率 ~1.1 Hz);(b)真机吊挂录 fit_actuator.py … 看能否在仿真里复现 1.25 Hz。谁先给出阳性结果谁定 v9 的方向。”
train/WALK_V8_SPEC.md § 9. 平行线 (倍周期) Order hardware runs by sim risk, gate each stage on the last, and put the fragile cell last with a spotter
risk-ordered-real-deploymentScript hardware sessions as a risk ladder: baseline first, sim-riskiest last with a spotter, suspended smoke before ground, each stage gated on the previous, environment (floor mu) recorded as a selection input - and stop at the stage that misbehaves.
Symptom
Five policy-x-gain combinations had to go on hardware in one session, with sim survival ranging from 20/20 down to 17/20 (and zero-command survival down to 2/20) - an unordered session risks breaking the robot on an avoidable run.
Context
The execution sheet fixed the order as sim-risk low to high, control baseline first (current SOTA establishes the floor reference), the fragile cell (fric-2400@kd1.0) last with a person spotting throughout. Stage gating: suspended smoke (feet off ground, 10 s each, all five pass before anything touches down) -> suspended with IMU and forward command (gait forms in the air) -> grounded runs -> speed raise only for combos that survived the previous stage -> zero-command tests only with a spotter, ordered by sim zero-cmd survival, with the 2/20 cell skipped by default. Preconditions include recording the floor material and estimating mu (if mu <~0.6, sim says pick the kd1.2 gain as main), port/CAN self-check, calibration frozen. Any stage failing stops the session at that stage: "任一段出问题就停在那一段, 不要跳到下一段".
Change
Session structured as a risk ladder with per-stage gates instead of a flat checklist; per-combo sim survival numbers written into the run table as the ordering key.
Outcome
The session design localized any failure to the cheapest stage that could reveal it, kept the robot safe for the informative fragile run, and made the control baseline available before any comparison run.
Mechanism
Hardware sessions consume a shared budget (robot integrity, battery, floor time); ordering by predicted risk means information is bought cheapest-first, and stage gates convert an expensive failure into a cheap earlier one. Baselines run first because every later reading is relative to them.
Applies when
- taking multiple policies/configs to hardware in one session
- a candidate is known-fragile in sim but must be measured
- writing a deployment runbook for a new robot
“跑序 = sim 风险从低到高, 最险的放最后 (依据 = 存活门/零指令存活) … ⑤ 是 sim 里最脆的一格 … 放最后跑, 全程留人扶, 起步即给 cmd, 零指令不做。… 任一段出问题就停在那一段, 不要跳到下一段。”
train/REAL_RUN_S2.md § 上机名单 / 全部命令 Four consecutive fixes were each continued from the previous fix's degraded state until the user stopped the ladder - "change parameters, don't stack errors" - rolled back to the last good checkpoint and audited the target geometry first
stop-stacking-roll-back-and-auditWhen successive rungs each start from the previous rung's output and the target symptom does not move, stop, roll back to the last good checkpoint and re-derive the next change from an audit; keep the measurements, discard the stacked remedies.
Symptom
After the real-robot splits, the V2.7 ladder tried to widen the stance: a term swap (A), a new stance knife (b), more iterations (甲), a doubled weight (乙). Stance barely moved while hip yaw ratcheted 46.7 -> 49.9 -> 52.5 deg toward its 60 deg limit.
Context
Each rung started from the previous rung's output. The user ruled on 2026-08-11 that things had gone wrong from V2.7-A: go back to v2_6 and rethink which parameters to change instead of stacking errors.
Change
乙 was killed at start and not counted; the product baseline rolled back to v2_6c model_29399; every measurement and law learned on the ladder was kept ("the data is real; what stacked was the treatment"). Before any new training, a zero-training kinematic audit of the stance targets was run.
Outcome
The audit found the stand_pose target itself rewarding the narrow stance (pose-target-geometric-audit) and showed geometrically why the yawed stance could not be widened with flat feet - so 乙 was proven unnecessary without running it. The next in-lineage attempts still failed, which is what established that the stance is set by the get-up path.
Mechanism
A rung continued from a degraded state inherits its compensations, so each new fix answers the previous fix's side effects; the yaw ratchet was the visible trace of that stacking.
Applies when
- three or more corrective rungs in a row without progress on the target metric
- a side-effect metric ratchets in one direction across rungs
- a new rung is being planned from the latest (not the best) checkpoint
“用户裁:"从 V2.7-A 开始就出问题了,应该回到 2.6 再思考如何改变参数而不是 错误叠加。"认账:A 的补丁 → b 的新刀 → 甲的加时 → 乙的加权,每级都从上级 的**退化状态**续(yaw 46.7→52.5° 的棘轮就是叠加痕迹)。 … 数据是真的,叠加的是处置。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §44 方法论裁定(2026-08-11,用户):V2.7 全阶梯叫停,回滚 v2_6 The hip_roll (l+r) asymmetry scalar predicted real-robot lateral drift - promote validated sim scalars into the gate
hip-roll-sum-predicts-lateral-driftHunt for cheap sim scalars that predict real-robot behaviors, validate them on direction AND ordering across multiple policies, then promote them into the acceptance battery; treat later violations as debt to justify in writing, not noise to ignore.
Symptom
A persistent hip_roll left/right asymmetry row in the sim2sim symmetry table had been dismissed as "calibration or mechanical asymmetry" noise; meanwhile real deployments drifted sideways by policy-dependent amounts.
Context
Forward-kinematics analysis reframed the scalar: both hip_rolls move the feet in +y for positive angle, so a same-signed (l+r) sum IS a lateral translation mode - the scalar is a direct lateral-drift bias estimate. Checked against real deployments: s1e (l+r = -0.0178, smallest magnitude) was the steadiest with least drift; 700 (+0.0253) drifted mildly left; A800 (+0.0267) drifted clearly left with the largest tilt 12.9 deg. Direction correct 3/3, ordering correct 3/3 (the log's heading calls it "四枚四中", four-for-four).
Change
The scalar was promoted into the acceptance battery as a posture-class criterion alongside tilt-max median: "hip_roll 左右不对称 |l+r| 不得比父代大" - doubling as a heat proxy (error ~ torque ~ heating).
Outcome
Used at every later gate; when the C4 product exceeded it by +0.005 rad (~+0.3 deg vs parent), the criterion was not silently waived - it was booked as explicit debt with a mechanism argument (the increment is task-required, far smaller than the sidewalk amplitude +/-2.2 deg) plus a related account (stand saturation 32.4% -> 37.2%).
Mechanism
A policy's static joint-angle bias in a translation-producing mode integrates into real-world drift; sim can measure that bias precisely and cheaply. A sim scalar earns gate status exactly when its predictions are validated against hardware in both direction and ordering - and a validated gate may only be exceeded with a written mechanism-level justification, never silently.
Conflicts
The log's heading says "四枚四中" (4/4) but the evidence table lists three policies and the text says "方向 3/3、排序 3/3"; the fourth instance is not shown in this file.
Applies when
- a real robot drifts or leans in a policy-dependent way
- deciding which sim measurements deserve gate status
- a validated gate criterion is marginally exceeded by a new product
“s1e | −0.0178（绝对值最小）| 微右、最不飘 | 三者中最稳、飘最小 ✓ … A800 | +0.0267 | 左、最飘 | 明显左飘、倾角最大 12.9° ✓ 方向 3/3、排序 3/3。 → 正式纳入验收表（与「倾角 max 中位」并列为姿态类判据）。”
train/C_LADDER_RUN.md § 3e. 顺带：hip_roll 左右不对称 (l+r) 就是横移偏置 —— 四枚四中 Fine-tuning through a reward-table change was falsified (scatter, half-recover, collapse) - continuation training is legal only with the reward frozen
fine-tune-reward-change-falsifiedNever fine-tune through a reward-table change - retrain from zero; reserve checkpoint continuation for frozen-reward plant/DR widening, reset noise_std when branching, and watch for the scatter/half-recover/collapse signature as the abort trigger.
Symptom
The s1c A/B experiment: arm B fine-tuned from an existing checkpoint under the revised reward (same contract, same network, changed reward + small DR) and failed with a characteristic signature - scatter, half-recover, fall back ("打散→半恢复→摔回"); arm A trained from zero under the same config won decisively (full shaping lifted swing to 21.6 mm within 500 iters; shipped at 5500).
Context
Verdict recorded: "从零 + 强塑形是本机唯一验证过的发育路径" (from-zero plus strong shaping is this machine's only validated development path). The signature became a standing stop criterion in every later rung that touched a reward ("s1c B 臂签名,出现即停"). Crucially the boundary of the law was drawn explicitly when S2 continuation training was proposed: "当年证伪的是「奖励表中途改版的 fine-tune」… S2 续训奖励表全程冻结、只逐级加宽 plant/DR,属另一类" - continuing a checkpoint with the reward FROZEN while widening plant/DR one rung at a time is a different class and was allowed (and then worked, powering the whole S2/C lineage) - with the honest fallback that if frozen-reward continuation ever collapses, that rung retrains from zero and the doctrine gets re-examined with data. Fine-tune arms also need mechanical care: reset the checkpoint's collapsed noise_std (terminal 0.033 "会杀死探索") and account for iteration counters re-zeroing (curriculum gates fire immediately).
Change
Reward changes and lineage continuation permanently separated: reward revisions -> from-zero retrain; plant/DR widening -> frozen-reward continuation with per-rung gates; the B-arm signature promoted to a universal tripwire.
Outcome
No later reward revision was attempted by fine-tune; frozen-reward continuation carried S2 (PD/COM/friction rungs) and the C command ladder successfully from the s1e root.
Mechanism
A trained policy sits in an optimum of its reward's geometry; changing the reward moves the optimum but leaves the policy's exploration noise near-zero and its value function calibrated to the old returns - it disassembles the old solution faster than it can assemble the new one. Widening DR under a frozen reward instead keeps the optimum's identity and asks only for local robustification.
Applies when
- proposing to fine-tune an existing policy under a revised reward
- planning a robustification ladder from a validated checkpoint
- a continued run scatters then partially recovers then collapses
“B 臂 fine-tune 证伪(打散→半恢复→摔回——从零 + 强塑形是本机唯一验证过的发育路径)。… 当年证伪的是「奖励表中途改版的 fine-tune」(B 臂,塑形突变致终盘摔回);S2 续训奖励表全程冻结、只逐级加宽 plant/DR,属另一类;若 s2_lag1 续训本身塌方,回退方案 = 该级从零重训,续训教义再议(拿数据说话)。”
train/OMNI_V0_SPEC.md § 3. S1.3 / 4. 与 s1c fine-tune 证伪的关系 Fall recovery was defined as the whole chain - any fallen pose, a stable stand, a clean hand-back to walking - and built as a second policy behind a deploy-side switch, not folded into the walking PPO
recovery-two-policies-and-a-state-machineDefine a recovery skill by the whole chain it must complete, including the hand-back to the next controller; if it is built as a separate policy, make the switching logic and its handoff contract a deliverable of their own, and keep the recovery observation contract a subset of the locomotion one so a unified policy stays possible later.
Symptom
A walking robot that falls needs a human to stand it back up. The design question on 2026-08-09 was whether to teach getting up inside the existing omni walking policy or beside it.
Context
The user set the goal as "any fallen pose -> stand up alone -> stand stably", and the spec named the real difficulty as the full chain fall -> recovery -> stable stand -> correctly initialised walking history and clock -> walking, making the deploy state machine a first-class deliverable. A unified single policy had a real-robot precedent (arXiv:2605.18611, a state-dependent gate near 37 deg tilt) but was deferred until a recovery policy and an omni policy were each reliable. The line ran on its own branch and worktree with every walk/stand/omni/run config path untouched. The development path copied the G1 learned get-up logic (arXiv:2502.12152): first find any feasible get-up (ugly accepted), then add smoothing, torque and real-robot constraints. The recovery contract kept the base 45-dim observation (command slice held at 0, no gait phase, no frame history - their reasons do not apply to a skill without a clock or a velocity task), so it stays a prefix of the 215-dim omni contract and a later merge is not foreclosed.
Change
Two policies and a deploy-side switch instead of one retrained walking policy; recovery got its own minimal contract (45 dims, full-range action, later the beta-anchored profile) and its own acceptance battery.
Outcome
The split held for the whole line: on 08-14 deploy_policy gained a second (PolicyIO, ONNX) pair behind --recovery-policy, each loaded under its own manifest contract, and the runbook runs stand_v1b or omni_c4_ff800 as the locomotion side with recovery_v3_1p1c. The literature scan of 08-10 found that every verified get-up implementation deploys one end-to-end policy (or softly gated experts) and stages only on the training side - so the runtime state machine here is the walk/recovery switch, not a staged get-up.
Mechanism
A separate policy keeps each reward table single-purpose and lets a proven walking lineage stay byte-frozen; the cost moves to the handoff, where every piece of state one policy leaves behind (history, clock, last action, command) must be reset for the other.
Applies when
- adding fall recovery or get-up to a robot that already walks
- choosing between one unified policy and a switched pair of policies
- designing the observation/action contract of a secondary skill
“先做 recovery policy + omni policy 两个策略,部署侧状态机切换;不把 recovery 硬塞进现有 omni PPO。 … 任务定义:**任意跌倒姿态 → 自己站起来 → 稳定站立**。真正的难点不只是"起身", … omni walk**(§6 部署状态机是本 spec 的一等公民,不是附录)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §0 目标口径与架构判决(用户 2026-08-09 定) Adapting a lineage to one plant increment needs hundreds of iterations, not thousands - long runs only buy specialization
continuation-budget-not-from-zeroBudget continuation rungs by increment class (hundreds of iterations for plant pins and smooth shifts, ~1000-1500 only for behavior-demanding changes like push), enforce a hard cap with frequent evaluation, and treat remaining budget as a reason to stop, not to continue.
Symptom
The default "6000 iterations per rung" (a from-zero-scale budget) was about to be applied to continuation rungs whose only change is one plant/DR increment - overspending compute and, worse, giving each rung thousands of iterations to specialize away retained skills.
Context
The 2026-08-07 budget table replaced the default with "最低适应窗口 + 每 100 iter 验收 + hard cap" scaled to the increment's difficulty: fixed-latency levels 300-500 (cap 500-800; the base has already seen in-band values, this only pins the plant); PD full-band 700 (cap 1000; kp+/-20%/kd+/-30% clearly widens the actuator family); COM +/-20 mm 500 (cap 800; a smooth dynamics shift); friction DR 700 (cap 1000; contact and actuator friction change the gait/contact solution together); push 1000 (cap 1500; a non-static plant change requiring recovery behavior - hardest). Rationale: "续训适应一个 plant 增量不需要从零量级的预算,跑长了只是给特化时间". The C ladder reused the scheme (per-rung caps 500-2000 by increment type), and the deep-training hazard got its own name when long runs sold quality ("深适应卖质量" - deep adaptation sells quality).
Change
Per-rung iteration budgets set by increment class with hard caps and 100-iter watch loops; checkpoint selection inside the window by the smoke curve, never "run to cap because budget remains".
Outcome
S2/C rungs completed in 300-1500 iterations each; the recurring late-run degradations (collapse valleys at 1500+, vx+0.30 decay) fell outside most rungs' caps instead of inside their runs.
Mechanism
A continuation rung's learning problem is local robustification around an existing optimum - low sample complexity; iterations past adaptation are spent sharpening onto the current distribution, which is exactly how retained skills and margins erode. Budgets sized to the increment bound both compute and the specialization damage window.
Applies when
- planning iteration budgets for a robustification or command ladder
- a continuation run keeps improving its training metric late
- retained skills decay in the back half of long continuation runs
“「最低适应窗口 + 每 100 iter 验收(watch_ckpt --every 100)+ hard cap」—— 续训适应一个 plant 增量不需要从零量级的预算,跑长了只是给特化时间 … ⑥ push | 1000 | 1500 | 非静态 plant 变化,要学 recovery 行为,最难”
train/OMNI_V0_SPEC.md § 4. 每级 iter 预算(2026-08-07 用户定) Curriculum-gate a penalty to the phase where its disease occurs - early on it only taxes exploration
gate-penalties-to-the-disease-phaseFor penalties aimed at late-stage pathologies (freezing, saturation, degenerate attractors), ramp the weight in only after exploration noise has decayed; anchor the terminal weight to measured healthy-vs-sick raw values, and shift all related tripwires to after the ramp completes.
Symptom
The action_saturation penalty, applied from iteration 0 in v8a, taxed exploration itself: with init_noise_std 1.2 the sampled actions paid ~-2.45/step before any policy had formed - while the disease it targets (clamp freezing) is a LATE pathology (v9 froze at iteration ~2624).
Context
v10 re-introduced the same penalty behind a curriculum gate: weight 0 until iter 1000, ramping linearly to -1.0 by iter 2000 - present only when the disease can occur, absent while exploration noise dominates. The trust argument was evidence, not hope: in v8a the term, while active, had pulled joint_pos_ref from 0.041 up to 0.155 and climbing - proof it can extract a policy from the frozen pit. Weight magnitudes were anchored to measured raw values (healthy v5 0.310 / v6 0.106 vs frozen v7 1.145 / v9 1.22 per step: at -1.0 healthy pays 6-18% of tracking, frozen pays 60%+, standing ~0). v10c then isolated the gated term as THE anti-freeze mechanism by single variable, upgraded to untouchable status in v11: "S 的门控机制(v10c 单变量铁案:任何情况下 不许撤,只许调终值)" - and v11 dared to relax other penalties only because S stood guard.
Change
action_saturation gated 0 -> -1.0 over iters 1000-2000 (later terminal value tuned -1.0 -> -0.5 with the gate mechanism itself frozen); tripwires adjusted to respect the gate's timing (freeze check moved to iter 2500-3000 to give the ramped term its effect window).
Outcome
Freezing stopped recurring while early training kept full exploration; the mechanism graduated from experiment to invariant within two versions.
Mechanism
A penalty's incidence depends on who occupies its support: early in training that is exploration noise (whose suppression starves learning), late it is the converged pathology. Time-gating aligns the penalty's presence with its target's presence, buying the constraint without the exploration tax - and tripwire timing must then be computed from the gate schedule, not from ungated precedents.
Applies when
- a structural penalty punishes exploration in early training
- a late-onset pathology (freeze/saturation) needs a standing guard
- deciding when a curriculum ramp should engage
“v8a 实锤它的病根是"罚在采样动作上"——init_noise_std 1.2 的早期等于罚探索(~−2.45/步);而冻结是晚期病(v9 速率 2624 才死平)… 门控让它只在病发期在场。… v8a 里它在场时 joint_pos_ref 从 0.041 爬到 0.155 且仍在升——有从低谷爬出的实证。”
train/WALK_V10_SPEC.md § 2. S 保险 —— action_saturation 课程门控 Torque caps cannot soften footfalls - impact is falling-mass momentum, only the reward can treat it
landing-impact-not-fixed-by-torque-capsClassify each hardware symptom by the physics that sets it: quantities fixed by ballistic momentum at contact must be treated through the policy's trajectory (reward terms on approach velocity/force), never through actuator caps - and size such penalty weights against your own tracking reward, not a lighter robot's.
Symptom
Footfalls slammed at 1.78x body weight in sim baseline (human walking: 1.2-1.5x); the tempting hardware-side fix was cutting actuator torque limits.
Context
Measured directly: scaling torque limits from x1.0 down to x0.4 left peak landing force essentially unchanged (1.75 -> 1.78x body weight) - the impact force comes from the momentum of the falling mass at touchdown, not from motor effort. The fix has to change the trajectory, i.e. the policy, i.e. the reward: feet_contact_forces penalty above a threshold of 113 N (= 1.2x the 9.58 kg robot's weight), clipped, weight -0.005. The weight was sized locally, not copied: the reference robot's -0.001 would amount to 0.9% of tracking reward on this robot ("策略不会理它" - the policy would ignore it); -0.005 gives 4.4%.
Change
Added threshold-type contact-force penalty (-0.005, threshold 1.2x body weight) as one of v6-minimal's three changes; hardware torque cuts explicitly rejected as a footfall treatment.
Outcome
Landing force 1.72x -> 1.55x by v6 (target <1.5x, missed by 3% - progress booked honestly); the torque-cap dead end was documented so it would not be retried.
Mechanism
At touchdown the ground stops a ballistic mass; the impulse is set by approach velocity and effective inertia, which motors can no longer influence in the final instant. Only earlier trajectory choices (approach velocity, timing) reduce it - and those are selected by the reward, not by actuator limits.
Applies when
- footfall impact or landing noise on hardware
- proposals to derate torque as a softness fix
- importing contact-force penalty weights from another robot
“⚠️ 硬件限扭降不了落脚力 —— 砸地力来自下落质量的动量: 实测 tau ×1.0→×0.4, 落脚力 1.75→1.78× 体重纹丝不动。只有这条奖励能治。… ⚠️ 权重不能用 Pi 的 −0.001 —— 实测在我们身上只占跟踪奖励的 0.9%, 策略不会理它 (Pi 6.94 kg 更轻)。−0.005 给到 4.4%。”
train/WALK_V6_MINIMAL.md § ③ 新增 feet_contact_forces Two simulators disagreed 1.8x on one policy's torque demand - four explanations were eliminated with numbers, the surviving suspect was never tested, and neither reading was allowed to cancel the other
torque-disagreement-between-simulators-unresolvedWhen two simulators disagree on a safety-relevant quantity, eliminate the measurement explanations one at a time with numbers, name the survivor as a hypothesis, keep the pessimistic reading binding, and run the direct test (replay one action sequence open-loop through both plants) before the quantity is used to pass a gate for hardware.
Symptom
For R3.0, Isaac read hip_pitch torque demand at 75-80% of the limit (PASS); MuJoCo read the same policy at 148-152% (1.5x over the limit).
Context
Candidates were eliminated one by one: PD gains (identical, RS06 kp 30 / kd 1.5), the settle window (both skip the first 0.5 s), the statistic (worse-of-two-legs vs per-joint - explains ~15%), self-collision (the no-contact subset still read 152%), sampling (500 Hz peak vs 50 Hz sample - ~9%). About 1.8x remained. The prime suspect - Isaac's implicit actuator (PD solved inside the PhysX integration, chosen to mimic kHz firmware PD) against MuJoCo's 500 Hz explicit PD - was named but untested.
Change
The Isaac PASS was recorded as valid for the Isaac plant only; the prescribed decider was an open-loop replay of one action sequence through both plants, compared step by step, needing no training. It was upgraded to a precondition of R3.1.
Outcome
R3.1 ran in parallel with, not after, the replay, and the replay never appears as done. By §40 it was "the oldest open account" on the line, to be fed by real-robot logs - which the spec also never records. Meanwhile the 50 Hz sample under-read the peak by 34% as smoothing narrowed the spikes, so Isaac-side readings grew more optimistic exactly when the comparison mattered more.
Mechanism
Each measurement artifact explained a slice of the gap; what remained is a plant difference, and an untested plant hypothesis cannot license discarding the pessimistic simulator on a safety-relevant quantity.
Conflicts
The spec prescribes the open-loop replay (§23), upgrades it to an R3.1 precondition, then records that R3.1 ran in parallel without it (§24), and lists it as the oldest open account before hardware (§40); nothing through §50 (2026-08-14) records a result. Every later "torque gate PASS" on this line is an Isaac-plant reading plus a MuJoCo check, never a reconciled one.
Applies when
- Isaac and MuJoCo (or sim and hardware) report different torques, contacts or slips
- implicit vs explicit actuator models are in play
- a gate passes on one simulator only
“**同一个策略,一侧判 PASS 一侧判超限 1.5 倍。** … 口径项全部扣掉后仍剩 **~1.8×** 没有解释。 … 但**这条没有验证,不能拿它当结论去抵消 MuJoCo 的读数**。 … (做法:拿同一条 动作序列在两边开环回放,逐拍比 τ —— 不需要重训)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §23 MuJoCo 复核门:成功率更稳,但 τ 与 Isaac 差 ~1.8× 没收敛 FK-verify a borrowed reference's structure, then size its amplitude by the reference's job - it pins phase, the policy adds lift
reference-structure-fk-amplitude-divisionWhen borrowing a reference trajectory: verify its structural claim against your own kinematics (an invariant like flat-foot), assign it the phase-pinning job, and size amplitude low enough that the policy contributes the lift - moving toward a proven foreign value in halves, not jumps.
Symptom
walk_v4 had big knee swing (40-46 deg) but only 18-24 mm foot lift - amplitude without hip/knee/ankle phase coordination; later, walk_v5's real-robot swing ballooned to 73.6 deg (sim 55.7) with violent footfalls - amplitude over-driven by the reference.
Context
Structure first: Humanoid-Gym's 1:2:1 hip:knee:ankle reference was verified on the local model before adoption - the ratio exactly satisfies the locally derived flat-foot constraint hip - knee + ankle = 0, FK-tested at multiple amplitudes with sole pitch 0.00 deg throughout. Amplitude second, and here the first reasoning failed honestly: FK said shorter legs need LARGER reference scale (0.30 for 30 mm lift), and the FK was correct - but the premise was wrong ("FK 没错, 但前提错了"): it assumed foot lift must come from the reference. HighTorque Pi, same scale, uses 0.08 with a 0.02 m foot-height target - proof that lift is added by the policy ON TOP of the reference, whose actual job is pinning the phase relationship. Scale 0.30 made the reference the entire gait: over-constrained and over-driven. The correction went to 0.15, deliberately not Pi's 0.08: "一次只走一半, 留退路" (walk half the distance, keep a retreat).
Change
target_joint_pos_scale 0.30 -> 0.15 as one of v6-minimal's three changes, treating both the footfall force and the lateral kicking (yaw momentum scales with leg swing amplitude).
Outcome
v6 improved landing force 1.72x -> 1.55x, suspended tilt 45.9 -> 23.0 deg, turn-gain asymmetry 70% -> 19%; the later v6-halved-shaping experiment (35 mm -> 4 mm collapse) confirmed the reference still carries the gait's existence on this machine - the division of labor is real but machine-specific.
Mechanism
A joint-space reference plays two separable roles: encoding structure (phase relations that keep the foot flat) and injecting amplitude (energy). Structure transfers across robots and is checkable by FK against an invariant; amplitude is a negotiation with the policy, and over-assigning it to the reference removes the policy's freedom to modulate lift with state.
Applies when
- importing a reference gait / imitation target from another codebase
- reference amplitude reasoning based on leg length alone
- real swing amplitude far exceeds sim's under a strong reference
“FK 没错, 但前提错了。我默认抬脚必须由参考轨迹产生。HighTorque Pi 同尺度机器人 … 用 0.08, 而它 target_feet_height = 0.02 m —— 说明抬脚是策略在参考之上加出来的, 参考只负责钉住髋/膝/踝的相位配合。我们取 0.30 等于让参考本身就是整个步态, 过约束 + 过驱动”
train/WALK_V6_MINIMAL.md § ① target_joint_pos_scale 0.30 → 0.15 Before training a one-leg stand, the accounts and a probe showed the default gains could not hold it at all - kp 20 needs 0.39 rad of error to carry the static roll moment, more than the whole adduction range - so per-joint gains came first, and thermal limits set the session length
single-support-gain-authority-probeBefore training a posture that loads one joint statically, compute the steady tracking error load/kp and the series stiffness against m*g*h, and prove with a simple hand-written controller that the posture can be held under the deployment gains - change the gains first if it cannot; then size session length from the thermal account.
Symptom
The one-leg line (standing on one foot, the other folded back, no hopping) had to decide whether the existing gain profile could hold single support before any reward was designed.
Context
Hardware accounts (9.792 kg, COM 0.234 m high, 170 x 80 mm feet, legs 80% of the mass): moving the COM over one foot needs 107 mm of shift and the 20 deg hip-roll adduction range gives 131 mm - geometrically enough. The static frontal moment is 7.8-9 N*m, within RS02's 17 N*m - torque is enough. But at kp 20 carrying 7.8 N*m needs 0.39 rad of tracking error, more than the entire adduction range, and the real robot had already shown it: commanded +0.17, actual -0.04 (0.21 rad droop) under load, 0.0008 rad hanging - load, not the motor. A probe (probe_oneleg.py) then showed open-loop PD cannot hold single support on physics grounds, so the criterion became "an equilibrium exists and a hand-written 4-gain COM feedback can hold it": single-support roll stiffness is hip and ankle in series and must exceed m*g*h_com = 22.5 N*m/rad; ankle kp 12 in series with hip kp 80 gives only 10.4 (open loop 16/16 fell), ankle 60 with hip 80 gives 34.3 (52% margin).
Change
A per-joint gain profile (rl_oneleg: hip_roll kp 80, ankle_roll kp 60, the rest as rl_default) - which needed per-joint gain support in robot.yaml, the bridge, deploy and the trainer's actuator groups - decided before training. Thermal account: single support makes hip_roll the dominant heat load (about 7.8 N*m against a 7 N*m continuous rating), so acceptance and demos run in segments of at most 60 s with a temperature check.
Outcome
Under rl_oneleg the hand-written feedback held six cells cleanly for 6 s (hip_roll steady torque 2.1-3.4 N*m, half the thermal budget); under rl_default the same feedback on the same cells fell 0/4. The trained V0 policy then passed its 40-cell acceptance.
Mechanism
With PD position control, the steady error needed to carry a static load is load/kp; when that error exceeds the joint's range the posture is unreachable whatever the policy does, and series compliance between joints lowers the effective stiffness below the gravity stiffness that single support demands.
Applies when
- single-support, crouched or one-arm-load postures on PD actuators
- a joint "droops" under load on hardware but tracks well when hanging
- deciding whether a new skill needs its own gain profile
“但 kp=20 时撑住 7.8 N·m 需要 **0.39 rad 跟踪误差 > 整个内收行程**。真机已实测: 命令 +0.17 实际 −0.04（droop 0.21 rad），悬挂时 0.0008 rad——是负载不是电机。 … 单支撑滚转是 hip/ankle **串联**刚度，必须 > m·g·h_com = 22.5 N·m/rad；ankle kp12 串 hip80 只有 10.4（开环 16/16 全摔），60 串 80 = 34.3（裕 52%） … **rl_default 同反馈同格 0/4 全摔**（增益档必要性对照）”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §1-1 单脚站: 几何可行，卡点是 hip_roll 增益权限 / §2 A 线增益 / §5 probe 定谳 Removing a hand trim re-exposed the plant offset it had been silently compensating - and a slope scan told bias from sensitivity
hand-trims-hide-plant-offsetsTreat hand-tuned trims as undocumented plant measurements: before deleting one, find what it compensates and re-house that knowledge in the model or the reward budget; diagnose posture errors with a sensitivity sweep to distinguish constant bias from gain problems.
Symptom
After switching from the old hand-trimmed default to the clean geometric zero, the retrained stand policy's only regression was torso lean: 1.8 deg -> 4.1 deg backward.
Context
The old default's ankle-pitch trim (-0.0489/+0.0628) had been pre-compensating a fore-aft COM mismatch; removing the trim removed the hidden compensation, and the posture reward alone was too weak to win it back. A COM sensitivity scan settled what kind of problem this was: sweeping base COM offset -50 to +50 mm gave nearly identical slopes for old and new policies (~0.026 deg/mm) - "不是质心敏感度问题, 是恒定偏置" (not a sensitivity problem, a constant bias). Fix landed in stand_v1b: posture corrected to +0.24 deg while keeping symmetry (<=0.1 deg) and low effort (0.259), disturbance rejection better than both predecessors. Model credibility was checked the honest way: v0's sim prediction at the real COM position (-22 mm) was -2.31 deg lean vs real measured 2.2-3.1 deg - "预测精准命中" - which is what licensed trusting v1b's -0.52 deg prediction. (Side flag from the same file: a sign convention had been documented wrongly in early comments - gravity_base[0] > 0 is forward lean.)
Change
Trims retired in favor of explicit modeling: symmetric geometric default plus a posture-reward budget sized to carry the real COM offset; the offset itself known (real COM ~22 mm behind model).
Outcome
stand_v1b passed acceptance as the standing lineage's final version; the walk-line requirement "加大躯干姿态惩罚权重" was upgraded from suggestion to mandatory, since walking amplifies what standing tolerates (real walk_v1 hit 26 deg lean vs sim 7.4).
Mechanism
Hand trims are plant knowledge stored in the wrong place - invisible, asymmetric, and stale after recalibration; removing them re-exposes the raw plant error. A sensitivity sweep separates the two possible diagnoses (slope change = control problem; parallel offset = constant plant bias), each with a different fix.
Applies when
- cleaning up hand-tuned offsets/trims in defaults or calibration
- a posture bias appears after a default or calibration change
- deciding whether a lean is a COM-sensitivity or constant-offset issue
“两者斜率几乎相同(≈0.026°/mm),v1 只是整体多后仰约 2.4° —— 不是质心敏感度问题,是恒定偏置。成因:旧 default 的踝俯仰 trim(−0.0489/+0.0628)本就预补偿了前后质心偏差,换成零位 default 后这份补偿没了 … v0 在真机质心处(−22 mm)的 sim 预测为 −2.31° 后仰,真机实测 2.2~3.1° 后仰 —— 预测精准命中。”
train/RETRAIN_v2.md § 4b. stand_v1 独立验证结果 / 4c. stand_v1b 验收结果 Three times a joint-angle stand-in for a foot-level quantity was gamed or lied - the absolute ankle roll sold stance width to buy flat feet, a hip-roll criterion was confounded by 50 deg of yaw, and the joint table said 0.271 m where the feet were 0.159 m apart
joint-space-proxy-for-task-space-quantityExpress foot-level (task-space) goals and acceptance criteria in task space - link attitude and lateral spacing from world poses - never through joint angles that assume other joints are at zero, and measure the task-space value before trusting a joint-space estimate of it.
Symptom
The line's first real-robot get-up (v2_6, 2026-08-11) was "fairly stable", but after standing the feet were too close and the robot slid into the splits and fell several times; later reports added that it also got up through a split posture.
Context
(1) flat_feet penalized sum |q_ankle_roll|, but a flat foot is ankle roll compensating hip roll; the proxy taxed the compensated wide solution, and the untaxed combination was hips straight plus ankles at zero - flat and narrow. On hardware the lateral support shrank to hip width plus centimetres, lateral balance rested on 11 N*m ankle motors, and the feet slid apart. (2) The next rung's acceptance criterion "hip roll >= 20 deg" assumed zero hip yaw; at 50 deg of yaw the lateral contribution is x cos 50 ~ 0.64 - the same substitution again, inside a criterion. (3) A new task-space diagnostic reading the foot links' world poses measured v2_6c's stance at 0.159 m where the kinematic audit from joint angles had said 0.271 m (0.271 x cos 47 ~ 0.17).
Change
Rule written into the spec: task-space quantities are never expressed through joint-space proxies. V3.1's stance terms were all task-space: flat_feet_task from the foot links' world orientation, lateral foot spacing in metres, stand_pose stripped of both roll joints.
Outcome
From scratch with task-space terms (V3.1 P1c): lateral stance 0.355 m, foot residual tilt median 0 deg / P75 2.0 deg, all six criteria passing, mu 1.0-0.4 all 100%.
Mechanism
A joint proxy bundles the goal with everything else those joints do; the optimizer finds the combination the proxy does not tax, and a joint-based criterion silently assumes the other joints sit at their nominal.
Applies when
- rewarding flat feet, stance width, foot placement or end-effector pose
- an acceptance criterion is written in joint angles for a geometric goal
- joints with large yaw or coupled axes are involved
“**病根 = 关节空间代理**:`flat_feet` 罚 Σ|q_ankle_roll|(§41 取的简易口径)。 "脚掌平"的运动学正解是 **踝滚补偿髋滚**(q_ankle_roll ≈ −q_hip_roll) … 代理把"脚平"和"站距"绑死在一起卖了。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §43 真机首试入账(2026-08-11)判读:flat_feet 的代理口径错误 When training fails repeatedly, inject the target behavior open-loop - stop tuning rewards for an unverified behavior
open-loop-probe-before-reward-tuningAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop on the real plant/sim first, and only resume training once you hold a measured, safe, sign-verified target trajectory.
Symptom
Three sidewalk training rounds failed; hypotheses multiplied (exploration failure / wrong reference waveform / insufficient authority) with no way to pick between them by running more training.
Context
Instead of a fourth reward guess, the team wrote probe_side_ref.py: the candidate reference is injected open-loop on top of a frozen policy's output (bypassing PPO entirely), directly measuring "what happens if the robot literally does this waveform" - separating all three hypotheses in one experiment (5 seeds x 8 s per condition, several waveform families and gains). The probe immediately eliminated the authority hypothesis (full-amplitude execution, 5/5 survival) and localized the problem to the waveform/measurement side. The closing principle was written down after the saga: without a verified target behavior, tuning rewards is "在黑暗里试钥匙" (trying keys in the dark).
Change
Standing method: before opening another training rung on a failing skill, build an open-loop (or task-space) generator of the intended behavior, measure whether the physical system can express it and what it looks like - then train toward a verified, quantified target.
Outcome
The probe chain produced the verified waveform (reversed-sign triangle, half gain), quantified safe amplitude (tilt 8.2 deg at band top, foot distance clear of the wall), exposed the metric bug when probe and training disagreed, and ultimately supplied the feed-forward that made C4 pass in +100 iters.
Mechanism
Training couples exploration, reward design, and feasibility into one opaque outcome; open-loop injection cuts the loop and tests feasibility and waveform alone. A behavior demonstrated open-loop converts the remaining failure into a pure credit-assignment/reward question - and its measured trajectory becomes the reference itself.
Applies when
- repeated training failures on one skill with multiple live hypotheses
- uncertainty whether the platform can physically express the behavior
- a reference trajectory's shape/sign/amplitude is guessed, not measured
“三轮 FAIL 之后不再猜，写 train/probe_side_ref.py 把参考开环注入到策略输出之上（绕过 PPO），直接量「照这个波形做会怎样」，一次分开三个假说：甲 探索 / 乙 波形 / 丙 权限。”
train/C_LADDER_RUN.md § 3f. C4 真因定谳（开环探针） / 3k. 建议的下一步 Write each config's expected hardware signature before the session - and if reality disagrees, change the books, not the conclusion
preregistered-real-expectationsBefore hardware runs, write per-config expected signatures and the disagreement rule (hardware outranks sim; discrepancies get recorded, not reconciled); validate the harness by checking it reproduces at least one known real behavior.
Symptom
Hardware impressions are easily narrated after the fact; without written expectations, any real-robot outcome can be made to "match" the sim story.
Context
The S2 acceptance sheet carried a section titled "sim 侧预注册预期 (事后核对, 不许事后改)" - per-configuration behavioral signatures written before the session: s1e@0.8 the disturbance king (push 159/160, zero chirality, all-mu 20/20) at the cost of speed gates 0/20 and zero-command wander ~0.98 m with -29.5 deg/20 s rotation; fric-3000 "walks accurately but is easier to push over"; fric-2400 neither. Credibility check included: the sim harness had reproduced the already-recorded real behavior (pace in place + right drift + net rotation -30 deg/20 s), which "提高本单全部预期的可信度". The anomaly clause fixed the epistemics in advance: if results systematically disagree with sim, "不改结论改账" - don't massage the conclusion, write the discrepancy into the books, and per the earlier zero-warning lesson, hardware wins.
Change
Every hardware session ships with a pre-registered expectation table (signature per config), a baseline-match credibility check, and a written precedence rule for disagreement.
Outcome
The A/B session became falsifiable: agreement confirms the proxy, disagreement is booked as a proxy-bias finding rather than argued away.
Mechanism
Pre-registration converts qualitative hardware sessions into tests of the sim-to-real mapping itself; a reproduced known behavior calibrates trust in the remaining predictions; and fixing "who wins on disagreement" beforehand prevents authority from drifting to whichever source flatters the plan.
Applies when
- planning any hardware acceptance or A/B session
- the sim harness's credibility in this regime is unestablished
- post-session write-ups tempt narrative fitting
“⚠️ sim 复现了真机已记录的「原地踏步 + 右漂 + 净旋 −30°/20s」—— harness 与真机行为对得上, 提高本单全部预期的可信度。… 结果与 sim 系统性不符 → 不改结论改账: 写进 README 该节, 按 「Isaac 指标三次零预警」的教训, 以真机为准。”
train/REAL_RUN_S2.md § 2. sim 侧预注册预期 (事后核对, 不许事后改) / 4. 异常处置 When the training reset distribution changes, freeze the acceptance distribution separately and pin its seed - the same checkpoint measured twice differed by 3.8 and 10.2 points
frozen-acceptance-distribution-and-pinned-seedAcceptance distributions are frozen artifacts, decoupled from whatever the training distribution becomes and evaluated with a pinned seed, and every gate row carries its sample size so that a small-n row is never read as a regression.
Symptom
R0.3 added easier roll-arc start states to the training resets, and the acceptance script shared the training category table; separately, the same checkpoint scored side 3.8 points and mid 10.2 points differently on two runs of the same script.
Context
Acceptance ran 512 parallel envs drawn from the fall categories. Had it kept following the training table, 15% of acceptance samples would have landed on states easier than prone - inflated scores and generations that could not be compared. The two same-checkpoint runs had identical per-item height medians, so the ruler had not changed; the spread was reset resampling noise (side n ~ 169, sigma 2.3%; mid n ~ 35, sigma 8.3%). The spec's "20 seeds" had always meant controlled seeds.
Change
accept_recovery.ACCEPT_CATEGORIES pinned to the four R0-R0.2 categories and decoupled from the training FALL_CATEGORIES; --seed 20260809 pinned, after which two consecutive runs were bit-identical. The mid row (n ~ 35) was labelled the bluntest gate.
Outcome
Every later generation (R0.3 through V3.1) was scored on the frozen distribution and seed, which is what let R0.3's intermediate state be read as "no measurable gain" (62.7 -> 62.1%) and R0.2's mid drop be booked as noise rather than a regression.
Mechanism
An acceptance set that follows the training distribution measures a moving target, and an unpinned reset draw adds sampling noise that small-n rows cannot absorb.
Applies when
- the training reset or command distribution changes between generations
- repeated evaluations of one checkpoint disagree
- a small category drives a pass/fail decision
“**分布冻结**:`accept_recovery.ACCEPT_CATEGORIES` 钉死 §5 四类 … 与训练侧 `FALL_CATEGORIES` **解耦**。 … **side 差 3.8 点、mid 差 10.2 点**(h 中位逐项一致,证明不是尺子变了)—— 纯 reset 重采样噪声 … 钉死后两次连跑逐位相同。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §14 验收尺子的两处加固(R0.3 起生效,向后兼容) When a contract default changes, old policies must run under a pinned legacy profile - a silent clock swap is out-of-distribution on hardware
legacy-profile-pinningTreat every trained policy as bound to the contract values of its training era: version the deployment profiles, pin old policies to their era's profile in every command, and never let a changed default silently apply to an old artifact.
Symptom
The walk profile's gait clock moved from 0.40 s to 0.50 s for new training, but versions v5-v9 were all trained at 0.40 s - running them under the updated default would silently feed a 25% slower phase clock to policies that never saw one.
Context
The re-test runbook hard-codes --policy-profile legacy_walk_040 into every command for the old versions, with the warning not to omit the flag: the mismatch is invisible (no error, no crash) but puts the policy out of distribution on hardware, where the same file had already documented that off-clock operation collapses gait quality.
Change
Deployment profiles versioned per training era; historical policies permanently associated with their era's profile; runbooks write the profile flag explicitly rather than relying on defaults.
Outcome
Old policies stayed runnable and comparable after the contract moved on; the silent-mismatch failure mode was closed by convention.
Mechanism
Changing a shared default rebinds every old artifact to a contract it was not trained under; unlike a schema break, a value change produces no error - only degraded, unexplainable behavior. Version-pinned profiles make the binding explicit and permanent.
Applies when
- changing any default in the deployment contract (clock, scales, gains) while old policies remain in use
- writing runbooks that mix policy generations
- a re-tested old policy behaves worse than its era's records
“2026-08-02 起 walk profile 的时钟改为 0.50(WALK_V10_SPEC §3)。v5~v9 全是 0.40 训的,本文件所有命令已改带 --policy-profile legacy_walk_040 ——不要省掉这个 flag,否则是拿慢 25% 的相位时钟静默喂旧策略(分布外,真机危险)。”
train/REAL_SWEEP_V5_V8.md § 1. 预检 ⚠️ 时钟改为 0.50