Training Coach
Doctrine
A report may cite any of these as doctrine-N.
doctrine-1Contract freeze and fingerprint disciplineThe policy I/O contract (observation layout, scales, history semantics, action pipeline) is frozen and fingerprinted; every exported policy is stamped and verified; contract changes ship as new versioned profiles that leave old artifacts bit-identical, and old policies run forever under their era's pinned profile.
Case. The 215-dim omni contract was frozen with a three-machine digest; the one contract-level extension (lateral feed-forward) went in as a new `omni_ff` profile with the old profile provably untouched, and the contract checker caught two real wiring bugs before any training (`contract-freeze-and-checker`). A silently changed gait-clock default would have fed old policies a 25% slower clock - closed by pinned legacy profiles (`legacy-profile-pinning`). A stale derived USD forked plant mass 2.2% until an automated source-vs-derived instrument gated it (`derived-asset-staleness-check`). A gain profile is part of the closed loop a policy was trained in and belongs in its stamp; the recovery line's anchored authority was left out of its manifest and recorded as the gap not to repeat (`gain-profile-belongs-in-the-stamp`), and a second policy behind a deploy-side switch made the handoff state itself a contract (`recovery-two-policies-and-a-state-machine`, `walk-recovery-fsm-handoff`).
Coach application. On any proposal touching obs/action semantics, defaults, or derived assets: demand the version/profile plan, the fingerprint update, and the checker extension in the same change; flag any old artifact that would run under new defaults.
doctrine-2Attribution by resolved training params - never eval-override knobsCapability differences between lineages are explained only by digging each lineage's *resolved* training configuration and eliminating columns; evaluation-side override knobs (kd-scale, power-scale, cycle-time) act on the plant for *every* policy and may serve as deployment mitigations but never as explanations.
Case. Low-friction robustness across 8 lineages x 3840 cells was traced to kd DR *bandwidth* - every lineage had ground friction pinned to (1.0,1.0), so "trained friction" could not be the axis; the parameter axis and the plant axis were explicitly separated after the first attribution conflated them (`kd-bandwidth-mu-law-attribution`). "Weak turning" on hardware was a power-scale plant effect, not a training gap (`deploy-knob-attribution-before-retraining`); slowing the deploy clock was out-of-distribution, not a feature (`cycle-time-override-is-ood`). The ground truth for what a run trained under is the logged per-run config, not the source tree (`resolved-config-is-source-of-truth`).
Coach application. Whenever asked "why is lineage A better", require the resolved-param table first; kill zero-variance columns; refuse explanations phrased in eval-knob terms; when a knob helps, label it deployment mitigation.
doctrine-3PASS gates become constraints; FAIL gates become objectivesOnce a skill passes its gate, that gate converts into a standing regression constraint (budget <= 2/20 against the parent baseline) for all later training; gates currently failing are the only legitimate objectives of the next rung.
Case. The C ladder ran one frozen 13-cell x 20-seed matrix at every rung with promotion = "new skill PASS and old skills within regression budget"; C1 was stopped and re-rooted precisely because it trained away the root's backward PASS (`fixed-acceptance-matrix-per-rung`, `preregistered-stop-criteria-per-rung`). The C4 product shipped only at 260/260 cells with zero regression.
Coach application. Keep the ledger: every PASS adds a constraint row; propose rungs only against FAIL rows; treat any constraint violation as stop-and-attribute, never "the next rung might win it back".
doctrine-4One variable per ladder rung - counted against what the checkpoint sawA rung changes one variable, where "one" is counted against the checkpoint's actual training state, not against the current config's diff; batching is allowed only when each change owns a disjoint symptom space with a pre-registered ablation order.
Case. Two rungs failed identically because resuming s1e-500 under the evolved config silently added four plant variables the checkpoint had never seen ("单变量纪律不只看「我改了什么」,还要看「checkpoint 见过什么」" - `resume-state-dr-audit`). v8 legally batched four orthogonal fixes with a written ablation order (`orthogonal-batch-with-ablation-order`); v9 spent one run completing a 2x2 factorial so either outcome convicted a factor (`fill-the-missing-factorial-cell`); v10b's three-way ablation wrongfully convicted the clock and had to be retried fairly.
Coach application. Before any resume: diff cfg against the checkpoint's logged training state. Before any batch: require the symptom-ownership map and ablation order in writing.
doctrine-5Pre-register risks, readings, and stop criteria before the ladderBefore a ladder or risky rung, write down the known risks, the interpretation of every plausible outcome, and hit-any-one stop criteria - frozen before training, tightened when priors say results should come fast.
Case. The C ladder opened with three numbered risks including the exact falsification condition for its own root choice; A/B arms carried "预注册读法(事后不改)" tables; a level expected to fail was run anyway for its pre-registered diagnostic value (`preregister-risks-and-fork-readings`). Stop criteria caught C4-redo rungs at +200 instead of full caps (`preregistered-stop-criteria-per-rung`); hardware sessions pre-registered per-config expected signatures and the disagreement rule "不改结论改账" (`preregistered-real-expectations`, `feasibility-accounts-lock-design-point`).
Coach application. Refuse to open a rung without the written risk/reading/ stop block; after results, read conclusions off the pre-registered table and flag any post-hoc reinterpretation.
doctrine-6Plant parameters are measured, never inventedEvery plant number carries measurement provenance: armature = N^2 x rotor inertia from no-load tests, friction split by rig and by API column, torque limits shaped by per-joint gait peaks, latency traced through the real pipeline, masses weighed - and DR bands are additive around the measured nominal, sized to the measured dispersion.
Case. Guessed friction was 2.5x low and guessed damping 5x high (`friction-measured-not-guessed`); armature had been 0 with a 9:1 gearbox (81x reflected inertia, `armature-n2-rotor-inertia`); a uniform torque derating was "the wrong shape" vs measured peaks (`torque-limit-shape-by-measured-peaks`); the delay implementation itself was a wrong plant for a whole lineage (`latency-lerp-reverse-extrapolation`); the run design point was locked by three accounts including the tau_limit/kd speed ceiling (`feasibility-accounts-lock-design-point`); identified friction had to land in the right simulator API columns to act at all (`sim-api-friction-columns`). The recovery and one-leg lines opened with the same kind of accounts before any reward existed - a connected static path and the torque along it for an armless get-up, and the gains single support needs to be holdable at all (`get-up-feasibility-accounts-before-training`, `single-support-gain-authority-probe`).
Coach application. For any plant value in a config review, ask "measured how?"; reject absolute ranges with no nominal; check API column mapping and derived-asset regeneration whenever measured values land.
doctrine-7Sim2sim gate before sim2real - under deployment conditionsEvery checkpoint passes a second, independently built simulator before hardware, and both the gate and the smoke loop run under the measured deployment conditions (real pipeline delay, honest contact parameters, the deployment gain/power profile).
Case. The standing order "先sim2sim 再sim2real" (`sim2sim-gate-before-sim2real`); acceptance flipped to match hardware only under measured condim/torsional friction (`eval-plant-honesty-contact-params`); gates moved permanently to `--delay 2` after the kicking incident (`pipeline-latency-is-plant-not-dr`); and the harness itself must be audited - a frame-convention bug in the cross-sim evaluator invalidated a whole line of verdicts (`body-frame-velocity-api-audit`). The recovery line's second simulator caught a torque penalty paid for by bracing the legs together (`torque-penalty-bought-by-leg-bracing`), and a 1.8x torque disagreement between the two plants stayed binding because its one surviving explanation was never tested (`torque-disagreement-between-simulators-unresolved`).
Coach application. Block any hardware request lacking a second-sim PASS at deployment conditions; when sim2sim and training-side metrics disagree, treat the evaluator as a suspect too.
doctrine-8Observation honesty - the actor's inputs are a hardware contractThe actor observes only signals the real robot produces with realistic noise; privileged truths go to the critic; history windows are estimators and must train under plant variation; rewards on quantities the actor cannot observe buy only average suppression, never closed-loop correction.
Case. Ground-truth velocity/forces went critic-only (`observation-honesty-critic-only`); frame_hist under zero DR memorized the trainer's plant fingerprint - 0/20 transfer (`history-obs-needs-plant-variation`); world-frame yaw rewards could not teach pull-back because heading is unobservable to the actor - correction was routed to the deploy outer loop instead of breaking the contract (`reward-observability-limit`, `deploy-heading-loop-and-align-training`).
Coach application. Audit every actor-obs element for hardware existence; require minimal plant jitter whenever history/recurrence exists; for each reward, ask "can the actor see this error?" and route correction tasks to outer loops.
doctrine-9Reward economics are audited in realized currencyReward design decisions are made on realized per-step magnitudes under the actual policy and command distribution: price the do-nothing optimum before adding a mode, compare achieved values to the computed ignore-floor, calibrate thresholds between measured healthy and sick distributions, and ship every new penalty with a withdrawal clause.
Case. feet_air_time at weight 2.0 realized 0.038 vs tracking 1.2 - drag was rational (`realized-contribution-audit`); ignoring a vy command cost 28-180x less than ignoring vx until a gated tracking term was added (`reward-cost-of-ignoring-audit`, `gate-new-reward-terms-by-command`); achieved-vs-floor separated "never learned" from "priced out" (`ignore-floor-diagnosis`); the foot-distance wall was placed between measured healthy (0.6% tax) and sick (55%) policies (`calibrate-threshold-between-healthy-and-sick`); the landing penalty carried a pre-registered stand-down condition and actually stood down (`calibration-threshold-with-withdrawal-clause`); two clearance terms were inert until zero-points and gate occupancy were checked (`inert-reward-term-audit`). A get-up policy sat because three gated terms paid the seated pose 84% of the return and the one term that could tell sitting from standing was an exp kernel reading 4.6e-5 at the real error (`seated-basin-dead-exp-kernel`); a torque-tail term was weighted by its measured steady value beside a peer term after the estimate proved 12x off (`tail-torque-needs-hinge-on-computed-demand`).
Coach application. Never discuss weights in the abstract: demand the realized-contribution table, the ignore-floor number, and the healthy-pay calibration before any reward edit is approved.
doctrine-10The zero-cost option must be the desired behaviorFor every penalty, name what the zero-cost option is; penalize failure events (slip, saturation excess, contact in flight windows), never the motion or joints that healthy behavior uses; make degenerate strategies fatal via termination where penalties cannot price them out.
Case. Joint-usage penalties for drift taxed a 1.4%-of-momentum channel 2.7/step and collapsed training; the slip penalty costs a non-slipping gait exactly zero (`penalize-the-slip-not-the-joint`). A frozen-at-clamp joint pays zero action-rate forever - only a pre-clip saturation penalty flips the cheat economics (`saturation-cheating-zero-rate-cost`). Ungated phase shaping made standing 42x more expensive than stepping and cooked the hip motors (`moving-gate-42x-stand-tax`); crouch-shuffling lived until a height termination deleted it (`termination-closes-degenerate-basin`). A gated penalty is an exit: the policy parked just outside an uprightness gate, then just under a height gate, to stop paying a stance tax, and only a positive band plus an always-on guard closed both (`penalty-gate-is-an-escape-hatch`); a soft-limit penalty that charged the standing pose itself bought a 4.1 deg lean (`soft-limit-penalty-charges-nominal-pose`); an unpriced foot attitude was spent on edge-standing (`unpriced-foot-attitude-is-a-free-variable`); and the one-leg line listed its cheapest cheats before training and still met one through a zero-gradient band (`enumerate-cheapest-cheats-before-training`, `binary-band-reward-fake-touchdown`).
Coach application. Run the "零代价的选项是什么" audit on every proposed term; convert motion taxes into event-conditional penalties; check the termination set against each known degenerate strategy.
doctrine-11Measurement discipline: independent referees, signs, distributionsA disputed measurement is adjudicated only by an independent algorithm from raw state; directional ability requires sign-antisymmetry under command reversal; bimodal metrics are reported as mode shares (never medians, never 3 seeds); ratios are not comparable when totals change; reward values compare only within one command distribution; single chaotic events never cross machines.
Case. The triple reversal - a good metric was "refuted" by a sibling metric that shared the disease (`independent-referee-for-metric-disputes`, `body-frame-velocity-api-audit`); same-signed +/- responses were bias, not turning (`same-sign-response-is-yaw-bias`); the swing median sat in a bimodal gap (`median-hides-bimodal-distribution`); "v6 is jitterier" died on absolute energies (`ratio-metrics-need-absolute-check`); yaw gain measured 15x wrong in an oscillating frame (`heading-integral-not-body-rate`); a 44% improvement evaporated under same-distribution comparison (`same-distribution-reward-comparison`); drift direction was a limit cycle (`multiseed-sign-test-for-drift`); a cross-machine push cliff was chaos (`single-impulse-recovery-is-chaotic`).
Coach application. Before accepting any surprising number: ask for the independent recomputation, the sign pair, the distribution shape, and the comparison conditions. Retract in writing when a metric falls.
doctrine-12The deployment pipeline is plantIrreducible pipeline properties - action latency, rate limits, power/torque scaling, teleop command mappings - are part of the nominal plant, modeled from day one and reproduced in every gate; deploy-side scalings are crutches that flag unmodeled plant, and they cannot be algebraically folded into training constants.
Case. Right-leg kicking was over-trained-delay x loop gain; power 0.8 was a gain-reduction crutch that retired when the delay was modeled (`pipeline-latency-is-plant-not-dr`); power derating damages non-forward axes first (`power-scale-hurts-nonforward-axes`); training at 0.4 scale as the "twin" of deploying 0.5 x 0.8 collapsed 0/20 (`deploy-scaling-not-training-equivalent`); one shared teleop speed sent an out-of-band lateral command and the robot clipped its own foot (`teleop-command-band-per-axis`); the latency DR range had not even covered the measured pipeline (`latency-dr-covers-measured-pipeline`). A rate limiter added at deployment only clipped a policy that kept commanding (`deploy-rate-limiter-windup`); moved into training and anchored on the last command it became an integrator in the balance loop (`slew-anchor-is-an-integrator`); anchored on the measured angle it bounded torque and kept the bandwidth (`beta-anchored-action-target`). The walking lines' safe setting, power-scale 0.8, cut the ends of the recovery policy's full-range travel and left its spikes alone; a gain inside the trained band did the job (`power-derating-cuts-full-range-contract`).
Coach application. Demand the measured pipeline latency/limits in the plant model and in gate conditions; treat every deploy-side derating as a question ("what is this compensating?"); block per-axis command sources that exceed training bands.
doctrine-13DR budget is finite; its distribution is the measured supportRobustness is a conserved budget: disturbance training on an already-hardened lineage borrows from existing margins; DR ranges span the measured deployment support - no fictitious tails (they buy degenerate gaits), no single constants (they allow thin-margin specialization); harden the plant only after the task distribution is final.
Case. The same push dose helped a narrow lineage and damaged a balanced one - budget conservation (`push-dr-conditional-budget-conservation`); wide latency tails bought drag-glide, constant values shipped 60% thinner tilt margins - the answer is a narrow band on the measured support (`dr-tail-plant-continuation`, `constant-value-dr-overfits-margin`); task-first ordering because hardening a soon-to-change task wastes budget (`task-shaping-before-plant-hardening`); COM randomization used deliberately as a behavior-shaping tool, and rolled back on symptom per its own contract (`com-randomization-forces-leg-spread`, `com-dr-rollback-on-symptom`). DR that is switched on can still be thin: the run policy fell in the frontal plane its gain-and-latency randomization never touched (`thin-dr-judged-by-channel-coverage`), and a friction priority settled under one action contract had to be re-measured under the next (`friction-priority-re-measured-after-plant-change`).
Coach application. Before any DR rung: check the untrained policy against the spec, the lineage's current DR load, and the measured real-world range; after it: audit retained margins, not just the new tolerance.
doctrine-14Gates measure what hardware feels: posture, margins, stripped assistsAcceptance batteries carry posture-class rows (tilt max median, per-joint L/R asymmetry, temperature) beside task rows, graded margin columns beside binary gates, chirality scored per side, at least one condition that removes the environment's free stabilization, and validated predictive scalars promoted into the gate.
Case. Three same-shaped judging errors - survival, displacement, wz-difference - all missed what the operator felt; posture metrics had the predictive power (`task-metrics-vs-posture-metrics`, `stand-gate-posture-not-survival`); binary survival saturated and hid a 60% margin gap (`constant-value-dr-overfits-margin`); v5 passed everything on the ground and failed suspended (`suspension-probe-removes-free-stabilizer`); the hip_roll (l+r) scalar predicted real drift direction and ordering and entered the battery (`hip-roll-sum-predicts-lateral-drift`); averages hide chirality (`chirality-scored-separately`); gait-quality gates are judged at speeds that demand a gait (`low-speed-commands-reward-dragging`). The recovery line added the rest of the kit: where failed episodes end, not only where they started (`end-state-confusion-matrix`); a frozen acceptance distribution with a pinned seed (`frozen-acceptance-distribution-and-pinned-seed`); video of the metric rollout itself (`video-as-acceptance-record`); and the admission that a 10 s episode cannot see a stance that fails after a minute (`episode-length-bounds-what-a-gate-sees`). The one-leg line removed a foot-spacing wall that no gate measured, and the feet met on hardware (`removed-wall-returns-on-hardware`).
Coach application. Review every battery for posture rows, margin columns, per-side scoring, and an assist-stripped condition; when operator feel and gates disagree, suspect the metric class first.
doctrine-15Fork and root selection: recoverability, maturity, frozen rewardsChoose fork roots by which candidate's deficits the coming training can pay back (precision is recoverable; lost plasticity, symmetry, and margins are not); prefer mature checkpoints as roots even when younger ones score better as products; never fine-tune through a reward change - continuation is legal only with the reward frozen and plant/DR widening one rung at a time.
Case. s1e-500 beat higher-precision candidates because its exclusive strengths were unrecoverable (`fork-root-recoverable-shortfall`); the b300 arm proved maturity is capital against adaptation shock (`root-maturity-vs-product-quality`); the B-arm scatter/half-recover/collapse signature falsified reward-change fine-tuning and drew the legal boundary for S2 continuation (`fine-tune-reward-change-falsified`).
Coach application. For root debates, build the exclusive-strengths table and ask "which side can be trained back?"; require dual-arm evidence for maturity claims; classify any proposed continuation as reward-frozen or not before approving.
doctrine-16Curricula: verified engagement, lineage counters, disease-phase gatingAutomatic curricula must prove they engage (a saturated ratchet is constant DR wearing a curriculum's name); every ramp counts lineage-cumulative progress, not per-process steps; penalties aimed at late-stage pathologies ramp in after exploration noise decays; difficulty rises on measured per-stratum success, never on schedule.
Case. The s1f ratchet capped at iter 248 and never engaged (`auto-curriculum-engagement-check`); the saturation ramp re-fired at +600 after every resume and no shipped product ever saw the penalty (`curriculum-counter-lineage-steps`); the same penalty worked once gated to the disease phase and became an untouchable mechanism (`gate-penalties-to-the-disease-phase`); record-high aggregate reward hid a fully-failing delay stratum (`aggregate-metrics-mask-subgroup-failure`); bucket share is not a gradient lever (`bucket-share-is-not-a-gradient-lever`). An assist curriculum keyed to a pooled success share was withdrawn on the strength of the categories that already worked (`curriculum-criterion-conditioned-on-lagging-category`); a pace set by per-step income moved only when that income was time-gated (`per-step-income-drives-speed-time-gate`), and the same gate had to be retired in a lineage without the disease (`time-gate-vs-wide-stance-retire-the-fix`).
Coach application. Ask every curriculum three questions: does it engage (show the internal state)? what does it count (process or lineage)? when is it present (against the pathology's phase)? Check where shipped checkpoints sit relative to every ramp.
doctrine-17Probe before training: feasibility first, hypotheses in tablesAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop, enumerate hypotheses in a written table audited against actual configs cheapest-first, race one probe per side of the sim2real boundary for hardware-only pathologies, and use suspended tests to acquit or convict actuators before blaming authority.
Case. "在黑暗里试钥匙" - four sidewalk rungs failed until an open-loop probe separated exploration/waveform/authority in one experiment (`open-loop-probe-before-reward-tuning`); the foot-drag mystery fell to a seven-hypothesis config audit (`hypothesis-table-code-audit`); the period-doubling was resolved by racing a reward-side and a plant-side evidence line - and both paid off, one per sub-case (`period-doubling-evidence-race`); the suspended test acquitted the roll actuator in one measurement (`suspended-test-isolates-actuator-authority`). A read-only configuration probe told a wall from a slope in the recovery line's seated basin (`configuration-probe-wall-not-slope`), and the fix it pointed to - where the feet are - took prone from 0/159 to 158/159 (`prone-dead-end-is-foot-placement`); a knob that did not move its variable was recorded as no test of the idea (`dof-vel-penalty-is-not-a-pacing-knob`).
Coach application. When a skill resists training, prescribe the probe before any further reward edits; require verified target trajectories before imitation terms; keep a falsified-fixes list so closed roads stay closed (`amplitude-cut-falsified-yaw-fix`).
doctrine-18External advice is recomputed locally; values transfer as ratiosEvery external suggestion is classified adopt / already-have / modify / trap by recomputing its claim on the local reward table and probe data; numeric values transfer only as dimensionless ratios (to tracking weight, leg length, sqrt(gL), control rate); citations are verified to exist.
Case. "Start vy very small" would have destroyed sidewalk learning on this reward table - the gradient scales quadratically (`external-advice-audit-against-own-arithmetic`); swing-height targets and weights transferred correctly only through leg-length and tracking-ratio scaling (`transfer-ratios-not-absolutes`); the "6-step delay" was refused for lacking a control rate (`latency-dr-covers-measured-pipeline`); a borrowed reference's structure was FK-verified and its amplitude re-derived from the division of labor (`reference-structure-fk-amplitude-division`); retrieval agents fabricated verbatim arXiv quotes - only source-verifiable material was used; and one dismissed suggestion later proved right for a different mechanism, and was credited (`cycle-average-tracking-for-gait-quantities`). An advisor's staged state machine turned out to exist in none of the three papers it cited, and reading them changed the plan (`advisor-paraphrase-vs-paper`).
Coach application. Intercept every "paper X does Y" with the local recomputation; convert absolutes to ratios before comparison; verify quotes; revisit dismissed advice when new mechanisms appear.
doctrine-19Hardware sessions are scripted experiments, not tuning sessionsReal-robot time executes a pre-registered matrix: risk-ordered (baseline first, fragile last with a spotter), stage-gated (suspended smoke before ground), A/B sessions bracketed by a repeated reference run, operators briefed on measured zero-command and untrained-axis behavior, chirality-aware disturbance protocols, no field tuning - the only legal field changes are scripted, single-variable, and self-reversing.
Case. The S2 acceptance sheet (`risk-ordered-real-deployment`, `battery-bracketed-real-ab`, `know-zero-command-behavior`, `push-test-chirality-protocol`, `no-field-tuning-protocol`); the RAM-only torque experiment with automatic power-cycle rollback (`reversible-single-variable-field-experiments`); and the sim-veto rule - even sim's condemnations get one safeguarded hardware check when they judge the purpose-built configuration (`sim-veto-needs-real-confirmation`). The recovery line's first real run went ahead with its preconditions unmet and was stopped as dangerous (`first-real-get-up-violent-stage-one-policy`); after it: a staged hang, mat and floor protocol (`staged-hang-mat-floor-for-get-up`), a fixed power-cycle pre-flight and two-machine discipline (`power-cycle-preflight`, `two-machine-config-discipline`), a fall guard replaced rather than switched off (`fall-guard-becomes-a-state`), and logs that are part of the run (`hardware-log-is-the-attribution-input`).
Coach application. Turn every hardware request into a runbook with order, gates, brackets, briefing, and anomaly plays; refuse improvised parameter changes on the floor.
doctrine-20Close questions in writing; restart when the debt is structuralAudited questions get frozen verdicts with citable wording and an explicit reopening bar; hardware verdicts are dated by deployment-stack and calibration state and expire when those change; and when successive rungs shuffle symptoms without net progress, freeze the lineage as regression baselines, pay the structural debts, and retrain minimal - carrying laws and instruments, not weights.
Case. The chirality and COM questions were closed with frozen wording and "no reopening without new hard evidence" (`frozen-verdicts-semantic-boundaries`); v5/v6's condemnations expired with the deploy stack (`stale-verdicts-under-old-stack`); a 2-degree calibration fix moved the whole runnable envelope (`zero-offset-calibration-shifts-envelope`); plant upgrades are era boundaries with paired re-baselining (`plant-swap-invariants-vs-shifts`); and the 2026-08-05 reset froze v5-v11, fixed the latency FIFO / manifest / sampling / reward-table debts, and restarted - producing the lineage that reached hardware SOTA (`freeze-lineage-fix-structure-restart`, `minimal-reward-table-with-provenance`). The recovery line's real-robot verdicts ended up in three places that disagree, one of them an undated note in a command file (`write-hardware-verdicts-back`).
Coach application. Maintain the closed-questions ledger and quote it when symptoms recur; stamp verdicts with stack/calibration versions; when a team is three rungs into symptom-shuffling, raise the restart question explicitly with the freeze-fix-restart pattern.
doctrine-21Name the quantity in the space it lives inA goal, reward term or acceptance criterion about the feet, the base or the contact state is computed from the quantity itself - world poses, forces, per-category outcomes - never through a joint-angle, single-signal or pooled stand-in that assumes everything else sits at nominal; and every detector is validated on a behaviour known not to contain the event before it becomes a gate.
Case. The recovery line was caught three times: |ankle roll| as "flat feet" sold stance width and the real robot slid into the splits, a hip-roll criterion was confounded by 50 deg of yaw, and the joint table said 0.271 m where the feet were 0.159 m apart; task-space terms produced the first flat, wide stance (`joint-space-proxy-for-task-space-quantity`). Flight detection lied in both directions across two lines - foot height flagged 40% false flight on a walking gait, contact force alone flagged slip chatter as hops (`contact-detector-single-signal-lies`). A pooled height average described a robot that did not exist - six in ten standing, four in ten sitting (`zero-partial-credit-is-not-an-iteration-problem`) - and the walking line had learned the same lesson on yaw rate (`heading-integral-not-body-rate`).
Coach application. For every reward term and gate row, ask what physical quantity it stands for and whether it is measured directly; flag joint-space or single-signal stand-ins for task-space goals, ask for a detector validated on a negative control, and split pooled metrics by category before reading them.
doctrine-22Continuation needs a live gradient; a release is chosen by a scanContinue a converged policy only on a change that creates a live gradient, on a short budget, with every checkpoint scanned on the transfer axis; choose a release by running the full battery over a band of checkpoints and stop on signals, never by taking the last one; and when edits to the terminal phase cannot move a behaviour, roll back and retrain with the constraint present from the start, keeping the order in which the lineage acquired its mechanisms as explicit curriculum phases.
Case. A continuation with no new gradient drifted MuJoCo transfer from 100/98% to 80/28% while every Isaac gate stayed perfect, and a live-gradient continuation at the same depth kept it (`converged-continuation-is-poison`). One-leg checkpoints 100 iterations apart failed 1 and 38 of 40 cells, and late ones degraded (`checkpoint-choice-is-a-full-gate-scan`). Four in-lineage stance fixes failed because the stance was the end of the get-up path, and from scratch it grew right (`stance-decided-by-get-up-path`); fixes stacked on degraded states were rolled back by the user (`stop-stacking-roll-back-and-audit`); and the lineage's final recipe, trained from scratch in one run, sat at 0% because the order of its curriculum was part of the product (`curriculum-history-is-part-of-the-product`). The omni line's short adaptation budgets and mature roots are the same law seen from the other side (`continuation-budget-not-from-zero`, `root-maturity-vs-product-quality`).
Coach application. Before approving a continuation, ask for the new gradient, the budget and the transfer axis in the scan; before approving a release, ask for the scan; after three rungs without progress on the target, propose rolling back to the last good checkpoint and a from-scratch phase plan instead of a fourth patch.
Experience cards
162 cards matching “com-dr-rollback-on-symptom”.
An exponential kernel on instantaneous velocity punishes gait oscillation - track the cycle average
cycle-average-tracking-for-gait-quantitiesReward velocity tracking on gait-cycle averages (or filtered values), not instantaneous samples, whenever the desired behavior oscillates at stride frequency; widening the kernel does not fix a variance penalty.
Symptom
Even while the robot genuinely sidewalked (verified after the metric fix), the Isaac-side tracking reward sat on the ignore-floor: true sidewalk scored 0.178 vs 0.189 for ignoring the command - the reward was mildly punishing the desired behavior.
Context
Sidewalking is inherently oscillatory: per-frame vy std was 0.177 while the tracking kernel width was sigma = 0.15, applied to the instantaneous value. A kernel-width scan showed widening sigma 0.15 -> 0.50 still loses (-0.14 -> -0.07): "指数核惩罚的是方差，而侧步天生带方差" (the exponential kernel penalizes variance, and side-stepping inherently carries variance). Modeling with measured parameters: replacing instantaneous vy with the mean over one gait cycle (0.5 s) flips the margin decisively (true sidewalk 1.888 vs ignore 1.281, +0.607), half-cycle is neutral (+0.006), two cycles adds nothing more. Explicitly flagged as extrapolation pending Isaac-side implementation. This also vindicated a previously dismissed external note (sigma too small) - right conclusion, different mechanism than claimed (variance, not gradient).
Change
Proposed fix recorded: change the tracked quantity from instantaneous vy to a one-gait-cycle running average; widening sigma alone rejected by the scan.
Outcome
Diagnosis complete and quantified; the C4 product shipped via feed-forward before the reward change was implemented, so the cycle-average fix remained a verified-by-model, not-yet-trained change.
Mechanism
E[exp(-(v-c)^2/sigma^2)] decreases with Var(v) even when E[v] = c exactly; a gait's phase-locked oscillation guarantees variance at the stride frequency, so instantaneous tracking rewards structurally prefer standing still at the command mean. Averaging over exactly one cycle removes stride-frequency variance while preserving command-following error.
Conflicts
The cycle-average fix itself is model-extrapolated ("⚠️ 这一条是外推，须在 Isaac 侧实装并复量后才能当结论") - the diagnosis is measured, the remedy untested in training at the time of writing.
Applies when
- tracking rewards for lateral/turn/any oscillation-carrying velocity
- a verified behavior scores below the ignore-floor
- choosing sigma for exp-kernel tracking terms
“侧走时 vy 的逐帧摆幅 std = 0.177，而 track_lin_vel_y_exp 核宽 σ = 0.15，且作用在瞬时值上 … 真侧走（均值 66%，振荡 ±0.18）0.178 | 完全无视指令 0.189 … 真侧走的得分比无视指令还低。… σ 从 0.15 放到 0.50，侧走仍然吃亏 … 把跟踪目标从瞬时 vy 换成一个步态周期（0.5 s）的平均 vy：… 1.888 vs 1.281”
train/C_LADDER_RUN.md § 3n. 二/三 Isaac 训练奖励为何一直坐在「无视底分」/ 修法不是放宽 σ Push-test protocol - positive side first, fragile side spotted, axes aligned in the log, and cross-machine push counts stay qualitative
push-test-chirality-protocolOrder disturbance tests from the robust side to the fragile side with protection scaled to sim-measured asymmetry, align and log frame conventions before testing, and treat cross-domain disturbance counts as qualitative evidence only.
Symptom
Hand-push testing on hardware risked falls on a side sim had already flagged as fragile, and push counts invited apples-to-oranges comparison with sim numbers.
Context
Sim chirality was explicit: descendants were far more fragile in -y (fric-3000@kd1.2: +6 N*s survived 15/20 vs -6 N*s only 3-9/20) while the s1e control was perfectly symmetric (40/40). The protocol therefore: push the positive direction first, keep a spotter for the negative side; before any push, record which real-robot side corresponds to sim's +y in the log ("上机前对一次坐标"); and - citing the chaos lesson ("混沌课文") - real push results are used only as qualitative corroboration, never compared numerically with sim survival counts across machines.
Change
Push testing became a scripted, chirality-aware protocol with frame alignment as a logged precondition and an explicit epistemic limit on cross-domain count comparison.
Outcome
The fragile side was tested with protection informed by sim's quantified asymmetry; logs stayed interpretable because the frame correspondence was recorded before the first push.
Mechanism
Disturbance-response chirality is a real, quantifiable lineage property, so test order should follow measured fragility; and perturbation outcomes are chaotic in the details (divergent trajectories from tiny differences), so counts do not transfer across domains even when qualitative rankings do.
Applies when
- planning push/disturbance tests on hardware
- sim shows directional asymmetry in disturbance survival
- someone proposes comparing real push counts to sim counts
“先正向后负向, 负向留人扶 —— sim 手性明确: 后代在负 y 向显著更脆 (fric-3000 @kd1.2: +6 N·s 15/20 vs −6 N·s 3~9/20), 而 s1e@0.8 两向 40/40 完全对称。上机前对一次坐标 … 跨机不做二值结论 (混沌课文): 真机推力只作定性对照, 不与 sim 计数对比。”
train/REAL_RUN_S2.md § 3. 抗推 (可选, 人手推; 做则按此协议) A soft joint-limit penalty charged the standing pose itself - the geometric-zero knee sat on its hard limit, so stand_v1 bent its knees to dodge 0.419 per step and leaned 4.1 deg forward; excluding the knee gave 0.24 deg
soft-limit-penalty-charges-nominal-poseBefore training, evaluate every penalty at the nominal pose; if a joint's soft limit sits inside the pose the task requires (a straight knee on its hard stop), exclude that joint from the soft-limit penalty and let the action clip enforce the hard limit.
Symptom
stand_v1 (retrained after the default pose moved to the CAD geometric zero and mirror augmentation was added) fixed left/right asymmetry (6.8 -> 0.0 deg) but settled at a 4.1 deg forward lean, where pure PD at the same default settled at 0.1 deg - the policy was actively pushing itself forward, which is exactly the real robot's failure direction.
Context
soft_joint_pos_limit_factor = 0.9 shrank the knee's soft limit to -/+0.1047 rad, while the geometric-zero default has the knee at q = 0, exactly on the hard limit. Standing in the nominal pose therefore paid 0.2094 x 2.0 = 0.419 per step in dof_pos_limits (alive earned only 0.5). The policy's way out was to bend the knees to -/+0.1013 rad, and the cost was the forward lean.
Change
stand_v1b: the knees excluded from dof_pos_limits (a straight knee IS the standing pose; the hard limit is still enforced by the action clip). No other change.
Outcome
stand_v1b: max tilt 0.3 deg, steady tilt 0.24 deg, asymmetry 0.1 deg, height 0.384 m - exactly nominal - with knees at -0.0007 / +0.0005 rad. It became the standing release used on the real robot, and later the standing side of the recovery switch. The same exclusion was carried into the recovery contract (knee at the clip in the standing pose) and the one-leg reward table.
Mechanism
A limit penalty whose soft boundary lies inside the nominal pose turns the nominal into a taxed state, and the policy buys its way out with whatever posture change is cheapest - here a knee bend paid for with lean.
Applies when
- a standing or default pose has a joint at or near its hard limit
- a policy settles in a small steady tilt that pure PD does not show
- soft-limit factors shrink limits uniformly across joints
“`soft_joint_pos_limit_factor=0.9` 把膝软限位内缩到 ∓0.1047,而几何零位 default **膝盖 q=0 正好压在硬限位上** ⇒ 站在标称姿态每步白扣 `0.2094 × 2.0 = 0.419` (alive 才 +0.5)。策略只能屈膝到 ∓0.1013 躲罚,代价是躯干前倾 —— 恰好是真机的 失效方向。 … 修掉"软限位罚标称姿态"后重训(`dof_pos_limits` 排除膝盖)。**前倾问题彻底消失** … 不再屈膝躲惩罚,高度正好落回标称 0.3840。”
train/README.md § 三期: 镜像对称增强 + 站立 v1 (2026-07-28) / stand_v1b (2026-07-28): 站立定版 Score left and right separately - averages hide chirality breaking that mirror augmentation does not prevent
chirality-scored-separatelyReport every mirrored skill as two numbers with an explicit gap budget; never accept an average, and never assume augmentation guarantees symmetry - measure it per lineage and treat breakage as hard to reverse.
Symptom
Policies developed quantified left/right asymmetry (e.g. C2-700 turned right at 82% but left at 67% - a 15 pp gap; push tolerance 40/40 symmetric on the root vs 17/40 on a deep-trained descendant), and averaged metrics would have reported healthy midpoints.
Context
The repo had policy-level symmetry-breaking evidence strong enough to make separate scoring a battery rule: "左右必须分开打分 … 平均 vy 跟踪会把它掩盖". Notably, chirality broke and never recovered even though mirror augmentation (command-level mirror_prob 0.5) was on the whole time - augmentation reduced but did not prevent asymmetry, and once broken it stayed broken through subsequent rungs. PASS conditions therefore carried explicit symmetry budgets (left/right tracking gap <=10 pp), and sim's predicted asymmetry (700: right faster than left) was flagged for direct real-robot timing confirmation.
Change
Battery rule: every directional skill reports left and right (CW/CCW) as separate rows with a max-gap budget; mirror augmentation treated as mitigation, not proof of symmetry.
Outcome
The 700-vs-A800 asymmetry gap (15 pp vs 7 pp) became a first-class selection criterion; C4 product shipped with a measured 5 pp gap.
Mechanism
Averaging over mirrored conditions cancels antisymmetric error exactly where it matters; and symmetry lost during training is a lineage injury (like plasticity loss) that later rungs do not spontaneously heal, so it must be gated, not assumed.
Applies when
- evaluating turn/sidewalk/push-recovery or any mirrored skill
- relying on mirror/symmetry augmentation
- selecting between checkpoints with similar average scores
“左右必须分开打分（left/right lateral、CW/CCW turn 各自一行）—— 本仓已有 policy-level symmetry breaking 的量化证据，平均 vy 跟踪会把它掩盖。”
train/C_LADDER_RUN.md § 5. 固定验收矩阵 (左右分开打分) A binary reward band on the swing knee had zero gradient everywhere below it, so the one-leg policy parked in an unloaded "fake touchdown" that Isaac's 5 N threshold scored as success and MuJoCo showed as real pressing - a capped constant-gradient ramp, retrained from scratch, passed 40/40
binary-band-reward-fake-touchdownShape approach-to-target rewards as capped ramps with gradient from the starting posture, never as bands or indicators; and compare contact-based terms across simulators, because a policy riding just under a force threshold looks perfect in one and wrong in the other.
Symptom
At iteration 1,000 of the first one-leg run the swing foot never lifted: the policy stood with the "raised" foot resting lightly on the ground. In Isaac the contact-match term paid 96% of full marks; the same policy in MuJoCo pressed that foot on the ground for 450 frames.
Context
The swing-leg goal was "shank folded fully back" (knee 1.5-1.95 rad), rewarded as a binary band: +0.8 inside [1.5, 1.95], zero elsewhere. From knee 0.05 to 1.5 rad the term was flat. Contact is judged at a 5 N force threshold, so a foot carrying less than 5 N counts as lifted. The walk line had hit the same disease with a binary indicator (v4) and fixed it with a capped ramp (knee_swing_amplitude).
Change
swing_knee_fold changed from the binary band to a ramp clamp(|q|/1.5, 0, 1) - a constant gradient capped near 86 deg - and the policy was retrained from scratch (V0r1). After the first real-robot try showed the fold still too low, its weight went 0.8 -> 2.0 (V0.1).
Outcome
V0r1 model_2300 passed the full acceptance 40/40 (swing knee 1.72 rad, about 98.5 deg) and was stamped as oneleg_v0.onnx; the cross-simulator disagreement is recorded as the thing that caught the cheat.
Mechanism
A reward that is flat until the target is reached gives no gradient to approach it, so the policy settles for the nearest state other terms reward - here, a foot that satisfies the contact threshold without lifting; a second simulator with different contact force resolution exposes such threshold-riding.
Applies when
- rewarding a posture target with an in-band / out-of-band indicator
- a contact threshold decides whether a foot counts as lifted
- trainer-side contact terms are near full marks while the video looks wrong
“初版二值带 [1.5,1.95] 在膝 0.05→1.5 全程零梯度，策略停在"卸力虚点地"（Isaac 5N 阈下 contact_match 96% 满分 / MuJoCo 同策略 450 帧实压——跨仿真器互证抓作弊）；v4 二值指示同型病，按 knee_swing_amplitude 判例改常数梯度封顶 ramp，从零重训 … **oneleg_v0.onnx = V0r1 model_2300, 40/40 PASS**”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §4 奖励表 swing_knee_fold 行 / §8 核查单 5 Every acceptance run records video of the very rollout that produced the numbers - the seated basin, edge-standing feet, tangled legs and the narrow stance were all seen on video before, or instead of, a metric catching them
video-as-acceptance-recordMake video a default output of every acceptance run, rendered from the same rollout the metrics come from (fixed views including the feet), and watch it - posture failures are visible before any gate row exists for them; never let video replace or override the numeric gate.
Symptom
Posture failures in the recovery line kept arriving as things the numbers had no row for: a kneeling W-sit, feet standing on their outer edges, crossed legs, a stance too narrow to hold on hardware.
Context
From 2026-08-09 (user decision) accept_recovery renders offscreen by default, following one env for the whole episode and archiving the clip. The MuJoCo gate's --video renders three views (side, front, feet) of the same rollout the metrics come from, with all plant modelling (delay, push); the older replay-based renderer produced an independent trajectory without delay and was not used for acceptance. Video never gates: if rendering breaks, --no-video keeps the numeric gate running.
Change
Video as a default acceptance artifact, named per policy, category and view, reviewed by the user.
Outcome
The R0.1 prone clip showed the same kneel-sit as R0; the R3.1 failure clip showed the crossed legs; the v2_5 feet view showed edge standing and led to V2.6; the v2_6 videos led the user to order a real-robot A/B between v2_5b and v2_6. Once, the recorder did not start (P1c final acceptance) and the visual material had to be produced separately.
Mechanism
Metrics exist only for failure modes someone anticipated; video shows the unanticipated ones, and rendering the metric rollout itself guarantees the picture and the numbers describe the same episode.
Applies when
- setting up an acceptance pipeline for posture-sensitive skills
- numbers pass but a human reviewer is uneasy
- sim videos are rendered by a separate replay tool
“**验收存视频(用户定 2026-08-09)**:`accept_recovery.py` 默认开 Isaac 离屏 渲染,跟拍一个 env 的整局并归档 … 跪坐这类盆地在数字表出现前肉眼先看见,视频是验收的 定性存档,数字门不受它影响”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §5 R0 验收门(预注册)验收存视频(用户定 2026-08-09) Training at scale 0.4 is NOT the twin of deploying 0.5 at power 0.8 - the algebra matches, the learned policy does not
deploy-scaling-not-training-equivalentNever assume deploy-side scalings can be folded into training-time constants ("burning the crutch into training"): the learned optimum depends on the training-time authority, so treat such conversions as full experiments with pre-registered expectations and a sim2sim gate before any hardware.
Symptom
s1g (S1.6) trained from zero at action_scale 0.4 - meant as the "training twin" of the hardware-proven s1c-at-power-0.8 (0.8 x 0.5 = 0.4) - was all green in Isaac (zero falls, reward 117) yet scored 0/3 across all eight checkpoints and 0/20 at 20 seeds in the MuJoCo gate, falling forward at median 1.57 s with a 2.9x speed overshoot.
Context
The pre-registered expectation (survival gate should pass, since the conviction matrix showed s1c@0.8+delay2 all-survive) was cleanly falsified, and the harness was acquitted by controls: --delay 0 fell identically (not a delay fragility), check_contract all green, and s1c through the same harness survived 2/3. The verdict: "「s1c@0.8 = 0.4 训练孪生」的代数等价不成立" - a policy deployed with a derated output still LIVES in the 0.5 internal model it trained under (its value function, its expectations of its own authority), while a policy that starts training with reduced authority learns a different, clip-hugging gait with zero margin for plant differences ("部署端打折的策略活在 0.5 的内模里,训练起点收权限学出的是贴 clip 的 另一套步态,对 plant 差异零余量"). Result: the policy was withdrawn before hardware ("撤回——不上真机"), the lineage root moved back to the 0.5-contract s1c-5500, and this became the C ladder's cited fact-check ("s1g 是 0/20 证伪出局的那一代").
Change
The amplitude-surgery route abandoned; contract kept at scale 0.5; the deploy-side 0.8 crutch later retired on its own merits when the delay-complete s1e generation ran at full power.
Outcome
One training run bought a clean falsification of a plausible algebraic identity; no hardware time was spent on it because the sim2sim gate caught it.
Mechanism
Output scaling commutes with the network arithmetic but not with learning: the training-time scale shapes which gait solutions are reachable and how much clip headroom the optimum keeps. A derated mature policy retains the wide-authority solution executed softly; a from-zero narrow-authority policy finds a different optimum that saturates its smaller envelope - the two are not the same controller in different units.
Applies when
- proposing to move a deployment derating into a training constant
- a scaled-down contract policy hugs the action clip
- Isaac-green / cross-sim-zero results on a re-scaled lineage
“预注册 a) 证伪——Isaac 全绿(零摔/reward 117)但 MuJoCo --delay 2 八档 checkpoint 扫描全数 0/3、iter6500 20-seed 0/20 … 「s1c@0.8 = 0.4 训练孪生」的代数等价不成立: 部署端打折的策略活在 0.5 的内模里,训练起点收权限学出的是贴 clip 的另一套步态,对 plant 差异零余量。”
train/OMNI_V0_SPEC.md § 3. S1.6 判决(2026-08-07 验收) When training fails repeatedly, inject the target behavior open-loop - stop tuning rewards for an unverified behavior
open-loop-probe-before-reward-tuningAfter two failed training attempts at a skill, stop training: demonstrate the behavior open-loop on the real plant/sim first, and only resume training once you hold a measured, safe, sign-verified target trajectory.
Symptom
Three sidewalk training rounds failed; hypotheses multiplied (exploration failure / wrong reference waveform / insufficient authority) with no way to pick between them by running more training.
Context
Instead of a fourth reward guess, the team wrote probe_side_ref.py: the candidate reference is injected open-loop on top of a frozen policy's output (bypassing PPO entirely), directly measuring "what happens if the robot literally does this waveform" - separating all three hypotheses in one experiment (5 seeds x 8 s per condition, several waveform families and gains). The probe immediately eliminated the authority hypothesis (full-amplitude execution, 5/5 survival) and localized the problem to the waveform/measurement side. The closing principle was written down after the saga: without a verified target behavior, tuning rewards is "在黑暗里试钥匙" (trying keys in the dark).
Change
Standing method: before opening another training rung on a failing skill, build an open-loop (or task-space) generator of the intended behavior, measure whether the physical system can express it and what it looks like - then train toward a verified, quantified target.
Outcome
The probe chain produced the verified waveform (reversed-sign triangle, half gain), quantified safe amplitude (tilt 8.2 deg at band top, foot distance clear of the wall), exposed the metric bug when probe and training disagreed, and ultimately supplied the feed-forward that made C4 pass in +100 iters.
Mechanism
Training couples exploration, reward design, and feasibility into one opaque outcome; open-loop injection cuts the loop and tests feasibility and waveform alone. A behavior demonstrated open-loop converts the remaining failure into a pure credit-assignment/reward question - and its measured trajectory becomes the reference itself.
Applies when
- repeated training failures on one skill with multiple live hypotheses
- uncertainty whether the platform can physically express the behavior
- a reference trajectory's shape/sign/amplitude is guessed, not measured
“三轮 FAIL 之后不再猜，写 train/probe_side_ref.py 把参考开环注入到策略输出之上（绕过 PPO），直接量「照这个波形做会怎样」，一次分开三个假说：甲 探索 / 乙 波形 / 丙 权限。”
train/C_LADDER_RUN.md § 3f. C4 真因定谳（开环探针） / 3k. 建议的下一步 Never referee a suspect metric with another metric from the same code - they can share the disease
independent-referee-for-metric-disputesTo adjudicate a disputed measurement, compute the quantity by an independent method from raw state; never accept a sibling column from the same pipeline as the tiebreaker.
Symptom
A triple reversal on one question: sidewalk sign diagnosis (correct) was retracted using a second metric from the same script, then the retraction itself had to be retracted when that second metric turned out to be the buggy one - two opposite-direction errors on the same problem in one day, both written into the execution sheet.
Context
The probe's net-displacement metric suggested the sidewalk reference sign was inverted. Worried about yaw-drift pollution of net displacement, the author checked the same table's body-frame vy_mean column (~0.003 everywhere, 20-50x smaller) and retracted the sign diagnosis. But vy_mean came from mj_objectVelocity, which was silently reporting vertical velocity due to a frame bug - the "referee" was the diseased measurement. Re-measured with a truly independent computation (xmat.T @ qvel, world trajectory), the original diagnosis was confirmed: saw -0.5 gave vy +0.058/-0.130 (76%/106%), consistent with the net-displacement values all along (yaw pollution was real but only 10-21 deg, nowhere near reversal-sized).
Change
Lesson written twice, verbatim, as a hard rule: when questioning a measurement, the referee must be an independent algorithm (different code path, different physical derivation), e.g. rotate qvel by the body matrix directly, or inspect the raw world trajectory.
Outcome
With the independent referee in place the frame bug was confirmed, fixed, and the whole C4 line re-scored - revealing sidewalk had been working (see body-frame-velocity-api-audit).
Mechanism
Metrics sharing a code path (or an upstream API) share failure modes; agreement between them is evidence about the code, not the world. Only a measurement with an independent derivation can break the tie, because its errors are uncorrelated with the suspect's.
Applies when
- two metrics of the same quantity disagree
- about to retract a conclusion based on a second readout
- auditing evaluation code after a surprising result
“我用一个坏指标去质疑一个好指标，并把撤回写进了执行单。教训（写死）：质疑一个测量时，不能用同一份代码里的另一个测量当裁判 —— 它们可能同源同病。裁判必须是独立算法（这次的裁判应该一开始就是 xmat.T · qvel[:3]，或直接看世界轨迹）。”
train/C_LADDER_RUN.md § 3m. 二 我今天犯了两个方向相反的错 / 3n. 五 元教训 A 2-degree joint-zero calibration fix moved the whole runnable envelope - re-test old "cannot run" verdicts after recalibration
zero-offset-calibration-shifts-envelopeDate every hardware verdict with the calibration state; after any zero/mount recalibration, re-test previously condemned policy-power combinations and previously "unexplainable" posture offsets before attributing either to training or model.
Symptom
s1d was on record as "only runs at power 0.7" (kicked wildly at 0.8); after a calibration pass, the same policy ran 12 s at 0.8 with no kicking at all.
Context
The calibration had fixed a 2.08 deg zero offset on r_hip_roll - exactly the constant error source on the dominant joint of the kicking oscillation loop ("恰是乱踢振荡环主导关节的常值误差源"). The three-generation post-calibration hardware sweep also closed a second case: the robot's mysterious "backward lean" disappeared after calibration, and the sim-real posture difference collapsed from opposite-sign 5+ deg to same-sign ~2 deg ("后仰案实质了结") - the lean had been a sensing/zero artifact, not a mass-model error. Booked consequence: if the s1d recovery re-verifies, "真机可跑档整体 上移" - every policy's runnable power envelope shifts up, and downstream lineages' hardware expectations get revised.
Change
Joint-zero and mount calibration promoted from setup chore to a variable that dates hardware verdicts: verdicts about which power/scale levels a policy can run are conditioned on the calibration state they were measured under.
Outcome
One policy rehabilitated at a higher power level; one standing sim-real posture discrepancy closed without touching model or training; a pending re-verification booked rather than asserted.
Mechanism
A constant joint-zero error acts as a persistent disturbance injected at the feedback loop's most-loaded joint; near an oscillation threshold, removing a 2-degree bias is the difference between a stable and an unstable loop. Since the error is additive and machine-side, it shifts every policy's stability envelope simultaneously - which is why verdicts must carry their calibration date.
Conflicts
The s1d rehabilitation awaited one confirming re-run at the time of writing ("待复核一跑坐实") - the offset-as-cause reading is the head suspect, not a closed verdict.
Applies when
- a policy oscillates at a power level others tolerate
- sim and real disagree on a constant posture offset
- deciding whether to re-test old hardware verdicts after maintenance/calibration
“发现①:s1d@0.8 能跑了(旧账「只有 0.7 能跑」)——12s 无乱踢。头号嫌疑 = 标定修正:r_hip_roll offset 修 2.08°,恰是乱踢振荡环主导关节的常值误差源。… 发现②:「后仰」标定后消失 … sim-real 姿态差从反号 5°+ 收敛到同号 2°,后仰案实质了结。”
train/README.md § 真机 @0.8 三代横评(2026-08-07 标定后) Compare the achieved reward to the computed ignore-floor to tell "never learned" from "learned but unprofitable"
ignore-floor-diagnosisFor any skill that trains flat, compute the reward the null policy would earn on that term; achieved==floor means the behavior never paid out (find why: exploration, reward observability, or feasibility) - do not tune weights first.
Symptom
C4 sidewalk failed on both arms; the question was whether the policy had found sidewalk and rejected it as unprofitable, or never found it at all - two diagnoses with opposite fixes.
Context
The theoretical value of the sidewalk tracking term for a policy that completely ignores the command was computable from the command distribution: 0.189. Trained final values landed at 0.187 (arm A) and 0.204 (arm B) - sitting exactly on the ignore-floor - while the honest balance at the optimum actually favored sidewalking (net +0.88/step inside the side bucket). Later the same arithmetic closed the whole saga: for the true reward landscape, doing real sidewalk scored 0.153 vs 0.944 for ignoring - the policy's refusal "是理性最优，不是探索失败" (rational optimum, not exploration failure) under one hypothesis, and under the final measurement-corrected account the policy had "每一次都在 做理性选择" (made the rational choice every time).
Change
Diagnostic rule adopted: compute the ignore-floor for the new term; if the achieved value sits on it, the behavior was never expressed in useful volume (or the reward cannot distinguish it - check both); if the achieved value is above floor but the behavior is absent at deployment, the policy sampled it and priced it out - then the reward balance, not exploration, is the lever.
Outcome
Correctly identified that PPO had not merely under-valued sidewalk; each subsequent hypothesis (waveform sign, regularization cage, exploration form, reward kernel) was tested against this floor arithmetic, which kept the search honest through three reversals.
Mechanism
Every reward term has a computable value under the null behavior; the achieved-vs-floor gap is a one-number audit of whether the optimizer ever monetized the target behavior. It converts "training failed" into one of two mechanistically distinct states with different fixes.
Applies when
- a new skill's tracking reward plateaus early
- deciding between exploration fixes and reward-weight fixes
- post-mortem of a failed curriculum rung
“track_lin_vel_y_exp 训练终值恰好坐在「完全无视指令」的底分上（A 0.187 / B 0.204，理论值 0.189），而终点 balance 明明有利（side 桶内净 +0.88/步）。不是学会了不划算，是根本没学到。”
train/C_LADDER_RUN.md § 3e. 为什么首战 FAIL mj_objectVelocity returns inertial-principal-axis frame - one API assumption poisoned eval and observations for a whole line
body-frame-velocity-api-auditVerify every frame-sensitive API against a hand-computed truth (rotate raw qvel yourself, or command a known world velocity and check where it lands) before trusting any evaluation or observation built on it - especially when a model's inertial frame is rotated from its body frame.
Symptom
Sidewalk vy read ~0 under every condition; separately, whole-policy performance was mysteriously mediocre in sim2sim while training-side numbers looked fine. Four training rungs were declared FAIL partly on these readings.
Context
base_link's URDF inertial frame is rotated 90 deg about x relative to the body frame (iquat = [0.7071, 0.7071, 0, 0]). mj_objectVelocity(flg_local=1) rotates into ximat - the inertial principal-axis frame - not the body frame, and returns center-of-mass point velocity, not body-origin velocity. Consequences measured: the "vy" column was actually vertical velocity vz (walking at cmd 0.25: old reading +0.0093 vs true -0.0424); the angular velocity fed to the policy in sim2sim was [wx, wz, -wy] - a different quantity than Isaac and the real IMU provide. RMS check over 8 s of walking: y/z axes swapped between v6[:3] and the qvel truth.
Change
Fixed sim2sim and both probes to compute ang_b = qvel[3:6] and lin_b = xmat.T @ qvel[0:3] (identical quantity to Isaac's root_ang_vel_b / root_lin_vel_b), with a standalone reproduction script (frame_bug_repro_0809.py).
Outcome
Re-scoring the "failed" C4 lineage under correct coordinates reversed the verdicts: c4r4 checkpoints showed vy 80-126% tracking (old reading: +/-2%) and vx+0.30 at 91-95% where the old metric said 0/5 - the bad frame both mis-measured vy and, via corrupted policy observations, systematically depressed all measured performance. Final product passed 260/260 cells.
Mechanism
A simulator API's frame convention is part of the observation contract; when the model's inertial frame is rotated relative to the body frame, frame-agnostic use of a "local" velocity silently permutes axes. Feeding a policy an axis-permuted angular velocity is an observation corruption that degrades behavior everywhere, not just on the axis being studied.
Applies when
- building or auditing a cross-simulator evaluation harness
- one measured axis reads near-zero under all conditions
- sim2sim scores are inexplicably worse than training-side metrics
- URDF/MJCF inertial frames are rotated relative to body frames
“base_link 的 iquat = [0.7071, 0.7071, 0, 0] … mj_objectVelocity 用的是这个 … 喂给策略的 base_ang_vel 是 [wx, wz, −wy] —— MuJoCo 侧观测与 Isaac / 真机 IMU 不是同一个量；vy_mean 报的是竖直速度 vz —— 前进 cmd 0.25 时旧读数 +0.0093，真值 −0.0424。”
train/C_LADDER_RUN.md § 3l. ⚠️ mj_objectVelocity 读的是惯性主轴系 / 3m. 一 bug 坐实 A joint frozen at the action clamp pays zero action_rate forever - penalize pre-clip saturation to make the cheat cost money
saturation-cheating-zero-rate-costWhenever actions are clipped and any smoothness/rate penalty exists, add a pre-clip saturation penalty so living at the clamp costs more than oscillating - and audit for frozen-at-clamp joints (action std ~0, |a| at exactly the clip value) as a standing acceptance row.
Symptom
With action_rate_l2 raised to -0.2, walk_v7's hip_pitch actions froze at exactly +/-1.000 (the clamp), reproduced bit-for-bit on hardware (splits frozen at +/-0.35 rad); the gait-shaping term joint_pos_ref collapsed to 0.026-0.035. The repo had died in the same trap once before (walk_v0: four joints pinned at +/-1.0).
Context
Mechanism: a joint pinned at the clamp has action-rate cost exactly zero and forever zero - under a strong smoothness tax, "push to the clamp and freeze" becomes the dominant optimum. Lowering the weight (-0.2 -> -0.1) only reduces temptation; the frozen state still costs nothing, so the structural fix adds action_saturation = sum(relu( |a_raw| - 0.9)) at weight -1.0, computed on the PRE-clip network output - post-clip, |a|=1.01 and |a|=3 punish identically and the out-of-range gradient dies (v0's old disease: mean |a| 1.71 soaked in saturation). Economics: freezing at |a|=1.0 now pays 0.1/joint/step (two hips = 40% of alive) vs ~0.0004/step for the healthy reference oscillation - the cheat flips from free to ~250x negative. Honest limits were recorded: A1 does not forbid freezing at 0.89 (the anti-freeze pressure must come from the oscillation demand of joint_pos_ref), and the alternative "rate on post-clip target" was rejected as 换汤不换药 - a pinned target also has zero rate.
Change
v8-A: add action_saturation (-1.0, thresh 0.9, pre-clip) AND halve action_rate_l2 (-0.2 -> -0.1, still 3.3x the v5 value); success criterion pre-declared (joint_pos_ref telemetry returns to v6 scale).
Outcome
Booked as the structural repair of the v7 freeze; also fixed a config hygiene trap discovered on the way - action_rate was assigned twice in __post_init__ (v5 comment line then v7 line), merged to one assignment "别再留两处赋值给下次审计埋雷".
Mechanism
Clipping creates a zero-gradient, zero-cost absorbing region in action space; any penalty on action derivatives makes that region strictly optimal once entered. Only a penalty on clamp proximity itself (measured pre-clip so depth of violation is visible) restores a slope out of the absorbing region.
Applies when
- joints sit at exactly the action clip with near-zero variance
- raising a smoothness penalty degrades gait amplitude
- shaped-oscillation terms collapse after a rate-weight increase
“钉死在钳位的关节 action_rate 代价精确为零且永远为零;−0.2 之下"推到钳位冻起来"成了压倒性最优 … 本仓第二次栽在同一坑(walk_v0 死于四关节钉死 ±1.0)。回调权重(−0.2→−0.1)只降低诱惑不消除作弊 … 算在 clip 前的原始网络输出上 … 作弊收支从"白赚"变成"倒贴 ~250 倍"。”
train/WALK_V8_SPEC.md § 1. 改动 A — 治饱和作弊 A sim veto needs real confirmation too - the worst sim cell was scheduled as the most informative hardware run
sim-veto-needs-real-confirmationNever let sim alone both condemn a purpose-built configuration and escape audit: spend one cheap, safeguarded hardware run on the condemned cell, pre-registering what agreement and disagreement would each imply about the proxy.
Symptom
The fric-2400@kd1.0 combination was sim's worst cell across the board (survival 17/20 - the only miss, mu0.4 1/20, push 103/160, zero-cmd 2/20), yet it was the only product specifically trained for the kd1.0 deployment gain - discarding it on sim evidence alone would leave the sim's own validity untested exactly where it mattered.
Context
The team had been burned in the other direction before ("Isaac 指标三次 零预警" - training-side metrics gave zero warning three times), so the symmetric rule was written: sim's rejection also needs hardware confirmation ("sim 判被支配 ≠ 真机被支配 … sim 的否决也要真机确认"). The run was pre-registered with a dual reading: real matches sim -> the S2f ladder closes and the fork root is settled; real clearly better than sim -> the MuJoCo proxy has a systematic bias in the kd1.0/low-margin region, "那比选型本身重要得多" - and every S2f sim acceptance would need re-scoring.
Change
The condemned configuration was kept on the hardware roster (last, spotted, minimal exposure) explicitly as a proxy-validation probe, not as a deployment candidate.
Outcome
Session design captured either result as progress: selection confirmed, or a proxy bias discovered that would re-price the whole ladder's verdicts.
Mechanism
Every sim verdict is a joint statement about the policy AND the proxy; cells where a policy was purpose-trained for the exact condition sim condemns are where proxy error is most likely and most costly. Testing the veto converts a selection decision into a calibration measurement of the evaluator itself.
Applies when
- sim rejects the configuration that targets the actual deployment condition
- the eval proxy's calibration has never been checked in that regime
- deciding which hardware runs are worth their risk
“但它也是唯一为 kd1.0 部署档专门训的产物 —— sim 判被支配 ≠ 真机被支配, 「Isaac 指标三次零预警」的教训反过来同样成立: sim 的否决也要真机确认。… 若真机明显好于 sim → MuJoCo 代理在 kd1.0/低裕度区有系统性偏差, 那比选型本身重要得多。”
train/REAL_RUN_S2.md § 上机名单 note / 2. sim 侧预注册预期 ⑤ Single-impulse push recovery is a binary chaotic quantity - cross-machine floating-point divergence can flip the outcome
single-impulse-recovery-is-chaoticNever gate or compare single-event recovery outcomes across machines or domains: evaluate disturbances as survival distributions over phases and seeds, compare longitudinally on one machine, and treat any single-point cliff as unconfirmed until it survives the statistical protocol.
Symptom
Mac evaluation found a hard "0.8 N*s cliff" (0/3 survival) that the training machine flatly contradicted: the identical protocol (0.8 impulse at 8 s, cmd 0.2) survived 3/3 there, and a 0.6/0.8/2/4 cross sweep survived everything.
Context
The verdict became a named lesson ("跨机混沌课文"): whether one specific push at one specific phase is survived depends on a trajectory that diverges across machines from floating-point differences alone - "单次冲量恢复是二值混沌量, 跨机浮点发散可翻结局". The boundary was drawn precisely: the 20-seed statistical gates DO agree across machines (established precedent), but that agreement cannot be extrapolated to single-point recovery tests. Protocol amended: disturbance evaluation uses multiple push phases (8/10/12 s), >=10 seeds, and only same-machine longitudinal comparisons; the Mac-side recommendation built on the unreproducible cliff was not adopted, while its directionally-consistent small-impulse data was kept.
Change
Push evaluation redefined from single-event pass/fail to multi-phase multi-seed statistics, with cross-machine comparison banned for event-level results and allowed for distribution-level ones.
Outcome
A false hardware-relevant "cliff" was prevented from steering the ladder (the s2e push rung decisions were made on same-machine statistics); the chaos lesson was cited again when real push tests were restricted to qualitative cross-domain use.
Mechanism
Perturbation recovery near the viability boundary has sensitive dependence on initial conditions; different BLAS/GPU reduction orders yield different trajectories from identical configs, so a binary outcome at one phase is machine-specific noise. Averaging over phases and seeds restores a quantity whose expectation is machine-stable.
Applies when
- a push/disturbance result differs between machines or sim and real
- designing push-recovery acceptance tests
- a sharp pass/fail cliff appears in a chaotic-regime evaluation
“训练机上 Mac 原协议 (0.8 @8s cmd0.2) 3/3 全活 … 与 Mac 的 +0.8 0/3 直接矛盾。定性: 单次冲量恢复是二值混沌量, 跨机浮点发散可翻结局;统计门 (20-seed 八门) 跨机吻合的先例不能外推到单点恢复测试。协议改判: 抗推评测多相位 (push 时刻 8/10/12s) + ≥10 seed + 只做同机纵向比”
train/README.md § s2e 支线终章 (跨机混沌课文) The deploy-side walk/recovery switch - into recovery at tilt > 65 deg held 0.3 s, back at tilt < 15 deg with angular rate < 1 rad/s and straight knees held 1 s, a 15 s timeout, last action cleared both ways - and the handoff steps the design required are only partly implemented
walk-recovery-fsm-handoffSpecify a deploy-time controller switch as hysteretic, time-filtered predicates the robot can measure (proxy what it cannot, e.g. straight knees for height), a timeout that ends in a safe stop, and a complete handoff (history, clock, last action, command ramp) - then test that the code performs every handoff step, because the design document is not the implementation.
Symptom
With a recovery policy and a locomotion policy as separate networks, the robot needs a switch: when is it "fallen", when is it "up", and what state must be reset so the next policy does not act on the previous one's history.
Context
The 08-09 design: enter recovery when fallen (tilt > 55 deg or height < 0.60 x 0.384 m) for 150 ms, leave for a stand-hold when upright (tilt < 12 deg, height > 0.85 x 0.384 m, feet steady, |omega| < 0.8) for 400 ms - wide entry, strict exit, hysteresis - then a mandatory handoff trio before walking resumes (reset the walking policy's observation history, restart its phase clock at 0, clear its previous action and latency buffer) and a command ramp instead of a jump. The 08-14 implementation in deploy_policy (--recovery-policy): each policy under its own manifest contract (walk: nominal + scale; recovery: beta-anchored), the same rl_default gains, the tilt cutoff disabled; RECOVERY at tilt > 65 deg for 0.3 s; LOCO again at tilt < 15 deg and |omega| < 1 and knees straight (< 0.35 rad) for 1 s - the robot's computer has no height estimate, and straight knees stand in for height so a V3.0-style upright kneel cannot pass as standing; RECOVERY longer than 15 s ends in a safe stop; last_action cleared on both switches; command forced to 0 during RECOVERY; power scaling applies to LOCO only.
Change
An open account was written down with it: the recovery end state (0.355 m stance, hip yaw -/+27 deg) is outside the walking policy's training start distribution, so the first test must use stand / zero command as LOCO, and the long-term fix is to widen the walking policy's initial states rather than bend recovery's stance to suit walking.
Outcome
The spec records only a successful compile (py_compile); the hang test was left to be done on site. The operator runbook carries the three-step procedure (hang with stand as LOCO, mat and push, then omni walk as LOCO) but no outcome.
Mechanism
Two policies trained separately each assume their own history, clock and last action; a switch that carries any of them across feeds the next policy a state it never saw - the design called this "the walking policy seeing a ghost history".
Conflicts
The 08-09 design requires resetting history, clock and previous action plus a command ramp; the 08-14 implementation records last_action clearing and a zero command during recovery; the one-leg spec of 2026-09-14 lists the handoff hygiene as specified but not implemented - reset_history() is called by nothing (a 215-dim policy would carry four frames of pre-fall history), the phase clock is not zeroed, and there is no command ramp back to LOCO. No hardware run of the FSM is recorded in either source.
Applies when
- switching between separately trained policies on hardware
- a policy with history or phase observations is re-enabled mid-run
- the robot lacks a sensor the switching criterion was designed around
“**判据**:进 RECOVERY = 倾角 >65°(`--fall-tilt-deg`)持续 0.3 s;回 LOCO = §5 真机可测子集:倾角 <15° ∧ |ω|<1 ∧ **膝直 <0.35 rad(NX 无高度观测, 高度门用膝直代理 —— 防 V3.0 型"跪坐但直立"误判)** 持续 1 s (`--recover-hold`);RECOVERY 单次 >15 s(`--recovery-max-time`)安全停。 … **切换卫生**:两向切换 last_action 清零;RECOVERY 态 cmd 强制 0”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §50 FSM 双策略调度(2026-08-14,用户令):deploy_policy --recovery-policy A get-up policy righted itself and sat - three terms paid the seated pose 84% of the return, and the only shaping term that could tell sitting from standing was an exp kernel outputting 5e-5
seated-basin-dead-exp-kernelWhen a policy parks in a degenerate posture, tabulate what each reward term pays that posture against the target (watch contact terms that reward touching rather than bearing load) and evaluate every exp kernel at the error actually observed; a kernel narrower than the real error is switched off, and widening it is a one-variable repair that adds nothing new.
Symptom
R0 converged by iteration 700 and gained 1.7% over the next 2,300; success 0.0% in all four fall categories. Three of four success conditions passed (tilt median 1.0 deg, both feet in contact 99.6%, angular rate low); height passed 0.6% (median 0.204 m against 0.326). The robot knelt in a W-sit: hip yaw +/-47 deg, knees folded to 92% of the hard limit, shins flat, pelvis on the ground, torso vertical.
Context
Minimal reward table: upright (1-g_z)/2 +2.0, base_height linear progress +1.5, stand_pose exp(-||q-q_stand||^2/std^2) x upright gate +1.0 with std 1.0, still +0.5 and feet_on_ground +0.5 both x the upright gate, plus regularizers. The upright gate is a hinge that opens below 30 deg of tilt. The pre-registered fallbacks were then checked against the measured state: tightening the tilt gate was falsified (tilt was already 1.0 deg); a success bonus contradicted the spec's own no-cliff-bounty rule; narrowing the categories was useless (all four converged to the same pose); raising init noise was too weak for a basin this deep. Only a half-rise intermediate state addressed it, and a cheaper repair existed.
Change
R0.1 (user decision, single variable): stand_pose std 1.0 -> 3.0. Not a new term and not a bounty - repairing a declared term that was numerically dead. The two runs' logged env.yaml differ in log_dir and std only.
Outcome
R0.1 58.2% overall (R0 0.0%): supine 91.5%, side 82.2%, mid 55.9%, prone 0/156; knees fully straight; ||q-q_stand||^2 9.99 -> 0.91 and the stand_pose term 4.6e-5 -> 0.90; get-up ~1 s, no re-falls, the curve still rising at the 3,000-iteration cap. Prone stayed at zero and needed a different fix (see prone-dead-end-is-foot-placement).
Mechanism
Sitting earned upright 1.98/2.0, still 0.43/0.5 and feet_on_ground 0.46/0.5 - 3.0 of a 3.57 per-second return - because feet_on_ground asked for contact, not load. The only terms separating sitting from standing were base_height (+0.70/s for standing) and stand_pose, whose kernel at the real 9.99 rad^2 error (75% of it in the two knees) was exp(-9.99) = 4.6e-5 with a gradient near 1e-4. Standing up meant risking 3.0/s to gain 0.70/s while unfolding knees at 92% of their limit under load. With std 3 the same term is exp(-9.99/9) = 0.33 - a live gradient, three quarters of it on the folded knees.
Applies when
- a policy converges early to an upright but low, seated or kneeling pose
- a posture-matching exp term reads ~0 in the training logs
- contact-based rewards saturate while the task metric does not move
“**关键:`feet_on_ground` 只问"触地"不问"承重", 跪坐时双脚确实贴地,照样满分。** 三项 3.0/s = 总回报 3.57/s 的 84%。 … **exp(−9.99) = 4.6e-5** —— 权重 1.0 的项实际输出 5e-5、梯度 ~1e-4, **不是"还没学会",是数值上根本不存在**。 … **R0.1 决定(用户 2026-08-09 定,单变量)**:`stand_pose` 的 `std` **1.0 → 3.0**。 不是加新奖励、不是悬崖悬赏,而是**修复一个已声明但数值失效的项**”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §11 R0 首跑(recovery_r0, 2026-08-09):FAIL —— 翻正了但坐着 Three same-shaped judging errors - task metrics (survival, tracking, displacement) cannot stand in for posture metrics
task-metrics-vs-posture-metricsKeep validated posture-class rows (tilt, per-joint L/R asymmetry, temperature) in every acceptance battery alongside task rows; when operator feel contradicts the gates, suspect the metric class before the operator - and never build a new skill on what is actually an asymmetry defect.
Symptom
The C2 product judged "full pass" on task metrics (A800: turn-gap 7 pp, vx+0.30 19/20) felt WORSE in the operator's hands than the half-pass 700: A800 tilted up to 12.90 deg (700: 6.64), drifted left while standing, showed larger per-joint asymmetries, and ran its hip_rolls 5 degC hotter.
Context
The re-judgment catalogued three same-type metric errors in one campaign: (1) stand judged by SURVIVAL - missed 0.5-1.4 m wandering; (2) stand ranked by DISPLACEMENT - ordering was opposite to real feel (tilt ordering matched); (3) chirality judged by wz-tracking GAP - measured turning symmetry while the robot's actual disease was postural left/right asymmetry, "两个不同的东西,且结论相反". Common pattern named: "我一直用「任务指标」当判据,而真机手感对应的是「姿态 指标」… 任务类指标不能替代它". The fix was already in the data: the per-joint left/right asymmetry table (printed identically by sim2sim and deploy) agreed with hardware in direction on every row - "判据可用、有预测力,我只是没把它写进 PASS 条件". Shipping decision followed the posture read: product reverted to 700 ("又一次「买到 精度、卖掉别的」"), and the C4 root moved to 700 as well, with the sharpest line of the episode: A800's left-drift "like sidewalking" is probably its frontal-plane asymmetry defect, not a capability - "在缺陷上建能力是危险的".
Change
Two posture quantities with demonstrated real-robot predictive power promoted into every PASS battery: tilt-max median and per-joint left/right asymmetry (both sim-computable, deploy-homologous); motor-temperature readout added to session close-out.
Outcome
Deployment flipped to the posture-better checkpoint; the hip_roll temperature table (43-48 degC vs 25-28) confirmed the earlier 90%-of-heat account; the run-line acceptance battery inherited the posture rows from birth ("任务类替代不了姿态类").
Mechanism
Task metrics measure goal attainment under the evaluator's episode definition; posture metrics measure the body state trajectory that operators, motors, and downstream skills actually experience. The two can rank candidates oppositely because task success tolerates postural pathology - so a battery without posture rows is blind to exactly what hardware feel reports first.
Applies when
- hardware feel disagrees with a green acceptance table
- choosing between checkpoints that split task vs posture metrics
- selecting the root for a skill that resembles an existing defect
“共同模式:我一直用「任务指标」(存活 / 跟踪率 / 位移)当判据,而真机手感对应的是「姿态指标」(倾角、逐关节左右不对称)。→ 验收判据里必须有姿态类指标,任务类指标不能替代它。… A800 的「左飘像 side walk」很可能 … 是它更大的额平面不对称的表现 —— 在缺陷上建能力是危险的。”
train/README.md § C2 选点改判 (2026-08-09): 手性判据第三次选错指标 An outer heading P-loop at deploy cut drift 10x because its output stays inside the trained command band - then training was aligned to it
deploy-heading-loop-and-align-trainingFix drift-class problems first with an outer loop whose output provably stays inside the trained command band; when adopting it permanently, align the training command generator to the deployment's actual command mixture (feedback-driven AND constant), matching law, gain, and clip exactly.
Symptom
Persistent heading drift on straight-line walking (v6 net yaw 60.3 deg over 15 s) that reward-side fixes had only partially tamed.
Context
The deploy stack added --heading: an external P loop wz = clip(0.5 * wrap_to_pi(theta0 - theta), +/-0.6), recomputed each frame and fed into the policy's ordinary wz command slot. Measured: net yaw walk_v6 60.3 -> 5.8 deg, walk_v5 17.4 -> 4.2 deg. A run-level audit later corrected the mechanism story: training had heading_command=False since v1 - the policy had NEVER seen heading-error feedback, so the loop works purely because its output lands inside the trained command distribution wz ~ U(+/-0.6): "收益真实,当时的机理解释写错了" (the benefit is real; the mechanism explanation had been wrong). v8 then closed the loop properly: training-side heading command enabled with rel_heading_envs=0.5 - half the envs get heading-error-driven wz, half get explicit constant wz, because deployment feeds wz BOTH ways (straight-line = heading feedback, turning = constant command) and rel=1.0 would have made constant-wz turning out-of-distribution. The law, gain, and clip were aligned item-by-item between trainer and deploy tool.
Change
Deploy-side outer loop first (no retrain needed); then v8-D enabled the matching training-side heading command at rel=0.5 with identical gain (0.5) and clip (+/-0.6), contract unchanged (wz slot carries the computed value).
Outcome
Drift handled at deploy (5.8 deg) generations before training caught up; the alignment removed the residual train/deploy distribution mismatch, with the accepted cost booked (open-loop straight walking becomes more OOD for heading-envs - irrelevant since acceptance and deployment always run the loop).
Mechanism
A learned velocity-tracking policy is a valid inner loop for any outer controller whose commands stay within the trained command distribution - the policy needs no knowledge of the outer objective. Full alignment then requires training on the same mixture of command sources the deployment actually uses, in the observed proportions.
Applies when
- heading/position drift on a velocity-tracking policy
- designing outer loops over learned locomotion controllers
- training command distribution differs from how deployment feeds commands
“审计更正(2026-08-02,run 级 env.yaml):训练侧自 v1 复盘起就是 heading_command=False … 策略从未见过航向误差反馈。--heading 是评估/部署侧外加的航向 P 环(wz=clip(0.5·err,±0.6), 落在训练分布 wz~U(±0.6) 内)。实测净偏航 walk_v6 60.3° → 5.8° … 收益真实,当时的机理解释写错了”
train/WALK_V7_SPEC.md § 0. 本轮之前已经改掉 (航向闭环, 含审计更正) IMU observation age cut 52-68 ms to ~4 ms by moving AHRS onto the MCU - as a single variable
imu-age-move-fusion-downstreamAudit observation age end-to-end and move time-critical fusion as close to the sensor as possible - and when you fix a latency, change only that one variable so the gain is attributable.
Symptom
IMU-derived observations reaching the policy were 52-68 ms old because attitude fusion ran in Python on the loaded host computer - stale attitude is a direct feedback-loop delay the policy was not trained with.
Context
The fix was scoped deliberately narrowly: move the AHRS computation from Python to the STM32 H7 (MC02). CAN topology explicitly unchanged, so the change is a clean single variable.
Change
AHRS fusion relocated Python -> H7. Before/after - IMU age: 52-68 ms -> ~4 ms; CAN timing: unchanged; Python load: high -> ~0.
Outcome
IMU age reduced by an order of magnitude with no confound; host CPU headroom recovered ("把计算单元搬在stm32上, 这样imu有剩余").
Mechanism
Sensor age is pipeline latency, not sensor quality: fusing on the MCU next to the sensor removes host scheduling jitter and interpreter overhead from the critical path. Keeping the bus topology fixed makes the improvement attributable to the relocation alone.
Applies when
- measured sensor-to-policy age far exceeds sensor sample period
- attitude fusion or filtering runs on a loaded host CPU in an interpreted runtime
- planning infrastructure changes during a sim2real campaign
“AHRS 搬到 H7——这个不改 CAN 拓扑，只是把一段计算从 Python 挪到 MC02，单变量：IMU age 52–68 ms → ~4 ms / CAN 时序 不变 / Python 负载 高 → ≈0”
Experience.md § AHRS 搬到 H7 (lines 28-35) Every power cycle starts with the same read-only pre-flight - read the buses, check the torque limits against 12/17/11, verify the IMU axes, check the ports after any new USB device - and any reassembly re-measures the joint zeros
power-cycle-preflightStart every powered session with a fixed, read-only pre-flight - bus responses, torque limits equal to the simulated ones, IMU axes, device identities - and re-measure joint zeros after any mechanical reassembly before running a policy.
Symptom
Hardware state drifts between sessions in ways no policy can see: a motor that stops answering after a power cycle, a torque limit that differs from the one simulated, an IMU axis flipped, two USB devices swapping identities, a joint zero moved by reassembly.
Context
The runbook's session order before any policy runs: read every motor on both CAN buses without enabling them (the first command after every power cycle); set_torque --check, all twelve motors must read 12/17/11 N*m, and any difference is written back; imu_reader --verify-axes, where the operator tilts the robot forward and to the right and every check must pass before continuing; check_ports after plugging in any new USB device (the IMU and a CAN adapter once collided on USB identity). After re-mounting motors: read the buses, then re-measure the calibration offsets (three repeats, written back) - "skipping it means running everything on the wrong zero". Hanging checklists repeat the torque-limit check (the deploy script also self-checks at start).
Change
A fixed, read-only pre-flight run in the same order every session.
Outcome
The runbook records one earlier hardware check in the same spirit: all 12 motors' implied kp fell within 18.4-22.0 for a commanded 20, inside the kp randomization range used in training.
Mechanism
A policy transfers only if the plant matches the one it was evaluated on; the pre-flight turns silent hardware drift into a failed check before the robot moves.
Applies when
- the first command after powering a robot on
- after swapping adapters, cables or motors
- a policy that worked last session suddenly behaves differently
“python tools/set_torque.py --check # 12 颗应全对 12/17/11, 有 diff 就 --write … 插任何新 USB 设备后都先跑一次 check_ports.py(IMU 和 CANable 的 USB 身份撞过车) … python tools/calib_stance.py --repeat 3 --write # 重标 offset —— 8/9/10 重新装, 机械零位变了”
RL系统/FOLLOW THIS copy 2.md § WALK / STAND 每次开始前 / 换CAN / 装回后必做两件 A stand gate judged by survival passes a robot that wanders a meter - judge posture instead
stand-gate-posture-not-survivalFor every gate, ask what behavior the metric is a proxy for and validate its ordering against real observations; replace metrics whose ordering disagrees with reality, and demote them explicitly rather than silently.
Symptom
Real robot "standing" drifted 0.5-1.4 m across the floor while the sim stand gate scored a clean 20/20 - because the gate's metric was episode survival, which wandering does not violate.
Context
C2's stand condition was originally written as "survival regression <=2/20". A real-robot counter-example on 2026-08-08 forced the re-judgment: wandering robots survive. Cross-checking candidate sim metrics against real-robot feel showed max-tilt median ordering agreed with hands-on ranking, while displacement ordering was actually OPPOSITE to real impressions - so displacement was demoted to a reference quantity, not a gate.
Change
Stand PASS criterion rewritten from survival to posture: "stand tilt max median <= root baseline +1.5 deg"; displacement kept only as reference. Applied to all subsequent rungs (C4 and redo levels inherit it).
Outcome
Later rungs gated stand on tilt (e.g. C4 product: 7.7 deg vs parent 7.1 deg, +0.6 deg PASS); the wandering failure mode became visible to the battery instead of hidden by survival.
Mechanism
A gate metric is a proxy for an intended behavior; survival is a proxy for "did not fall", not "stood still". Metric choice must be validated against ground truth (real-robot feel/measurement), and a proxy whose ordering disagrees with reality on real data is worse than no metric - it steers selection backwards.
Applies when
- writing PASS conditions for stand/idle/hold behaviors
- a gate passes policies that visibly misbehave on hardware
- choosing between candidate metrics for an acceptance battery
“stand 必须用位姿判，不能用存活判（2026-08-08 真机反证改判）：站着乱走 0.5~1.4 m 时存活照样 20/20 —— C2 的 stand 条件原写「存活退化 ≤2/20」，选错了指标。改为: stand 倾角 max 中位 ≤ 根基线 +1.5°（倾角与真机手感排序一致；位移排序与真机相反，降为参考量）”
train/C_LADDER_RUN.md § 3b. PASS 条件 ⚠️ stand 必须用位姿判 Run acceptance under measured contact parameters - honest condim/torsional-friction flipped a false PASS into a real-matching FAIL
eval-plant-honesty-contact-paramsPin the evaluation plant's contact model to measured values (contact dimension, torsional/rolling friction, mu) before trusting any gate that involves slip, impact, or drift - a gate can only fail a policy for physics its simulator contains.
Symptom
walk_v5 passed the old acceptance battery yet failed on the real robot (footfall force, drift, kicking) - the evaluation plant was flattering the policy.
Context
The battery was re-run under "honest contact parameters" - condim 4 (adding torsional contact) with measured torsional friction 0.035 - and v5 then FAILED exactly the rows corresponding to its real problems: heading 185 deg (limit 30), support-foot yaw slip 284 deg (limit 80), landing force 1.72x (limit 1.5x), suspended tilt 45.9 deg (limit 10). The slip physics depends on torsional friction, which the default contact model (condim 3) does not even simulate - a slip problem is invisible to an evaluator that cannot represent yaw friction at the foot. Term-sizing measurements for the new rewards were likewise taken under the same honest parameters (cmd 0.45, skipping the 5 s start transient).
Change
Acceptance harness pinned to condim 4 / torsion 0.035 (measured); verdicts issued under defaults declared non-citable for these rows.
Outcome
Sim acceptance verdicts began agreeing with hardware ("现在失败, 与真机一致"); the v6 fixes could be developed and validated against an evaluator that could actually see the disease.
Mechanism
An evaluator is a plant model too: contact dimensionality and friction values decide which failure modes exist in the simulation at all. Evaluating under default contact parameters tests the policy in a world where its real failure is physically impossible, producing structurally false PASSes.
Applies when
- sim acceptance passes policies that fail on hardware
- slip/drift/impact gates run under default simulator contact settings
- setting up a cross-simulator evaluation harness
“accept_v2.py 已加三条判据, walk_v5 在诚实的接触参数下(--condim 4 --torsion 0.035)现在失败, 与真机一致:直行 15s 航向累计 <30° | 185° ✗ … 落脚力峰值 <1.5× 体重 | 1.72× ✗”
train/WALK_V6_MINIMAL.md § 5. 验收 When a contract default changes, old policies must run under a pinned legacy profile - a silent clock swap is out-of-distribution on hardware
legacy-profile-pinningTreat every trained policy as bound to the contract values of its training era: version the deployment profiles, pin old policies to their era's profile in every command, and never let a changed default silently apply to an old artifact.
Symptom
The walk profile's gait clock moved from 0.40 s to 0.50 s for new training, but versions v5-v9 were all trained at 0.40 s - running them under the updated default would silently feed a 25% slower phase clock to policies that never saw one.
Context
The re-test runbook hard-codes --policy-profile legacy_walk_040 into every command for the old versions, with the warning not to omit the flag: the mismatch is invisible (no error, no crash) but puts the policy out of distribution on hardware, where the same file had already documented that off-clock operation collapses gait quality.
Change
Deployment profiles versioned per training era; historical policies permanently associated with their era's profile; runbooks write the profile flag explicitly rather than relying on defaults.
Outcome
Old policies stayed runnable and comparable after the contract moved on; the silent-mismatch failure mode was closed by convention.
Mechanism
Changing a shared default rebinds every old artifact to a contract it was not trained under; unlike a schema break, a value change produces no error - only degraded, unexplainable behavior. Version-pinned profiles make the binding explicit and permanent.
Applies when
- changing any default in the deployment contract (clock, scales, gains) while old policies remain in use
- writing runbooks that mix policy generations
- a re-tested old policy behaves worse than its era's records
“2026-08-02 起 walk profile 的时钟改为 0.50(WALK_V10_SPEC §3)。v5~v9 全是 0.40 训的,本文件所有命令已改带 --policy-profile legacy_walk_040 ——不要省掉这个 flag,否则是拿慢 25% 的相位时钟静默喂旧策略(分布外,真机危险)。”
train/REAL_SWEEP_V5_V8.md § 1. 预检 ⚠️ 时钟改为 0.50 An edge-triggered landing penalty missed the tail and fired after the harm - penalize overspeed continuously inside the contact window
penalize-tail-before-touchdownPenalties aimed at impact/violation events must (a) price the excess over a threshold, not the mean, and (b) be active on the approach (state-gated window), not triggered by the event - check your control rate can even see the event you are penalizing.
Symptom
The v7 landing penalty (vz^2 on the contact-force rising edge, weight -10) did not bite: landing-velocity 95th percentile stayed at 2.61 m/s against a 0.3 target.
Context
Two structural faults were identified: (1) it penalized the MEAN over sparse events - many soft landings dilute the occasional violent slam, while the damage (GRF peaks, motor peak load) lives in the tail; (2) it fired AFTER touchdown - at 50 Hz evaluation the rising edge is aliased by physics decimation, so the read vz is often the already-decelerated post-impact value: underestimated, and with no shaping gradient before contact. Replacement: continuous penalty while the sole is inside a height gate (h < 0.03 m): relu(-vz - 0.30) - only the excess over an allowed approach speed is penalized (tail only), and gradient exists for several frames BEFORE touchdown. The sole-height computation again subtracts the 0.0585 m link offset ("WALK_DIAGNOSIS 坑#1, 别再踩"); the edge-triggered version was kept as a diagnostic only.
Change
feet_landing_vel reformulated: edge-event vz^2 -> in-window relu(-vz - v_ok) with v_ok 0.30 (conservative vs the sqrt(L)-scaled human value ~0.19, to be tightened after passing), h_gate 0.03, weight unchanged -10.
Outcome
The failure analysis of the first form was written before the second was trained; the v_ok escalation path (0.30 -> 0.45 if the robot becomes afraid to land) was pre-registered in the risk table.
Mechanism
Sparse-event mean penalties optimize the average case while the constraint is a quantile; and any penalty evaluated only at/after a discrete event gives the optimizer no gradient along the approach trajectory that determines the event. A state-gated continuous excess penalty fixes both: it prices only violations and shapes the approach.
Applies when
- impact/landing penalties fail to move tail percentiles
- a penalty is triggered by contact edges at a coarse control rate
- designing constraint-style penalties for rare violent events
“罚的是均值路径:上升沿是稀疏事件 … 大量软着陆稀释偶发猛砸;而伤害在尾部 … 罚在触地后:50 Hz 评一次,上升沿被物理 decimation 混叠,读到的 vz 常是撞完已减速的值——既低估,又没有触地前的塑形梯度。”
train/WALK_V8_SPEC.md § 2. 改动 B — 落地惩罚改罚尾部、罚在触地前 Model CAN polling skew - joint observations are 6-9 ms stale by read order
can-timing-skew-modelingIf joints are read sequentially over a shared bus, reproduce the per-group observation staleness in sim (or randomize it over the measured range) - synchronous observations are a privileged fiction.
Symptom
Policies trained with synchronous joint observations degrade on hardware where motors are polled sequentially over CAN - hip data is already 6-9 ms old by the time ankle data arrives.
Context
Menlo's core sim2real finding on a leg platform of almost identical mass to Lucen's. CAN is a sequential bus: one poll cycle reads motors in a fixed order, so the observation vector mixes timestamps. Lucen runs 6:6 motors on a dual CAN split, so the problem transfers one-to-one.
Change
Explicitly model CAN timing skew in sim: give the joint groups different observation delays matching physical read order. Menlo went further - running real firmware in the loop with a motor simulator between MuJoCo and firmware injecting 0.4-2 ms uniformly distributed delay.
Outcome
Reported by the reference team as their core sim2real enabler on a same-scale platform; recorded in Lucen's experience log as directly applicable ("这个问题一模一样").
Mechanism
A policy exploits any cross-joint temporal coherence present in training observations; when hardware breaks that coherence per bus position, the learned feedback acts on inconsistent state estimates, injecting phase error exactly at the control bandwidth.
Conflicts
Second-hand episode: outcome numbers are the reference team's report, not a Lucen-run experiment; Lucen adopted the requirement but the corpus has no Lucen A/B of skew-on vs skew-off.
Applies when
- robot polls actuators sequentially over CAN/RS485 or similar shared bus
- sim2real degradation appears as jitter or oscillation not seen in sim
- designing the observation/delay model before a training run
“电机走 CAN 是顺序轮询的，髋部电机的数据到踝部电机上报时已经陈旧了 6-9 ms，他们直接在仿真里显式建模了 CAN 时序偏斜，按读取顺序给三组关节不同的观测延迟。… 注入 0.4–2 ms 的均匀分布延迟。你们是 6:6 双 CAN 分总线，这个问题一模一样”
Experience.md § 执行器 + 时序建模 (line 6) Before training a one-leg stand the spec named the cheapest cheats - hopping on the support foot, a raised foot resting unloaded, a leg tripod - and gave each a countermeasure and a gate; one still appeared and was caught by exactly those gates
enumerate-cheapest-cheats-before-trainingBefore training, list the cheapest behaviours that would satisfy each reward term without doing the task, give each a countermeasure in the reward and a gate in acceptance, and prove the intended behaviour is reachable with a probe - then treat any gate the policy games as evidence about the reward, not the gate.
Symptom
The literature's single-leg benchmark reports eight state-of-the-art general policies holding a clean one-leg stand 0 times out of 90 - they survive by sneaking steps and hops - so the task's first adversary was the policy's own cheating.
Context
The spec's shape self-check ("what is the zero-cost option?") listed, for the one-foot bucket: the cheapest cheat, a foot resting on the ground without load, countered by a 5 N contact threshold plus positive swing income; the second cheapest, small hops on the support foot to reset balance, countered by a continuous support-air penalty plus a gate of zero support-foot flight segments. The probe that preceded training had already seen a third: early low-lift postures "survived" by pressing the swing foot at 78-95 N, a leg tripod, removed by folding the shank back. The two-foot bucket was checked too: its zero-cost behaviour is ordinary standing, with no odd base state.
Change
Countermeasures and gates written before training: swing-contact and support-air penalties, gate 2 (zero swing-foot contact frames above 5 N), gate 3 (zero support-foot flight segments).
Outcome
The first run still found the unloaded-foot cheat (a binary reward band gave it no gradient to lift) - and it was caught, by the contact gates and the cross-simulator comparison, not discovered on hardware. The retrained V0 passed all gates 40/40, including zero support-foot flight after the flight detector was corrected.
Mechanism
A policy optimizes the reward, not the intent; the cheapest behaviours that satisfy the reward are predictable from the reward's structure, and a gate written for each before training turns a silent cheat into a failed row.
Applies when
- designing rewards for balance, contact or "hold still" tasks
- benchmark policies are known to cheat the task
- writing acceptance gates for a new skill
“文献里 8 个 SOTA 通用策略在单脚站基准上 0/90 干净保持， 全靠偷步偷跳活命，这是本任务的第一反作弊对象 … 单脚桶下最便宜的作弊是"脚虚放地上不受力"——接触判定 >5 N 力阈（沿用），配 swing_height_band 正收入拉开。 … 第二便宜是"支撑脚小跳重置"——support_air_penalty 连续罚 + 验收门支撑脚腾空段=0 双保险。”
git:Lucen V2@origin/oneleg-line:train/ONELEG_V0_SPEC.md § §0 目标口径 / §5 形状自检(零成本选项是什么) Every rung gets written stop criteria - hit any one, stop; tightened when priors say results should come fast
preregistered-stop-criteria-per-rungFreeze per-rung stop criteria (old-skill floors, new-skill deadline, oscillation signature, known pathology signatures) before training, stop on first hit - and shorten the deadline in proportion to how fast your mechanism says results should appear.
Symptom
Continued training past the point of degradation had previously destroyed capabilities (C1 trained away the root's backward skill); without hard stop rules, sunk-cost reasoning keeps runs alive too long.
Context
Standard rung protocol - eval_c_matrix every 100 iters at 5 seeds with a fixed criteria list, frozen before training ("开训前写死，事后不许改"): (1) stand or vx+0.15 at <=3/5 for two consecutive points; (2) vx+0.15 tracking <70% for two consecutive points (vs recorded root baseline); (3) oscillation signature - survival repeatedly crossing zero between adjacent checkpoints, stop on first occurrence, do not wait for confirmation; (4) new-skill-no-progress deadline (e.g. wz tracking <30% or still same-signed after iter 400); (5) a known lineage pathology signature (s1c arm-B: scatter -> half-recover -> collapse).
Change
Stop budgets scale with prior knowledge: when C4-redo4's feed-forward was already proven open-loop, the no-progress deadline was tightened from +500 to +100 iters ("前馈是开环就给 71~96% 的 … 若 +100 还没有 … 不值得再烧").
Outcome
Multiple rungs were stopped exactly on criterion (C4-redo criterion 4 at iter 1200; redo2/redo3 at absolute 900), converting each into a clean hypothesis test instead of a drifting run; no rung burned its full cap on a dead hypothesis.
Mechanism
Degradation of retained skills is a lineage-level injury that later training often cannot undo, so detection latency is capital loss; and a stop rule written before the run cannot be bent by hope. Tightening deadlines when priors predict immediate results converts "no result yet" into evidence against the mechanism.
Applies when
- starting any resumed/curriculum training rung
- deciding whether to keep training a run that shows early regression
- a mechanism-backed change should produce results immediately
“每 100 iter eval_c_matrix.py --seeds 5，命中任一即停 … 存活在相邻 checkpoint 间反复跨越 0（出现即停）… 收紧版：绝对 iter 900（= +200）时 vy±0.10 跟踪仍 <30% 即停”
train/C_LADDER_RUN.md § 3h. 预注册停梯判据（开训前写死，事后不许改） The median of a bimodal metric lands in the empty gap - check the distribution, and never judge swing on 3 seeds
median-hides-bimodal-distributionBefore quoting a median or mean, look at the distribution; report suspected-bimodal metrics as mode share plus per-mode ranges, use small-seed smoke runs only to screen trends, and size the seed count for decisions by the share resolution you need (here: 20).
Symptom
Years of "high swing variance" and undecidable 3-seed swing readings turned out to be one fact: the metric was bimodal all along - "历代 swing 高方差与 3-seed 不可判由此定性:一直在测双稳态系统" - and every median reported from it (e.g. 12.1 mm) described a value no seed ever produced.
Context
Concrete instances: s2e_pd-1400's 20 seeds split 2.6-4.9 mm vs 19.3-24.0 mm with zero seeds between; s1e-500 read 3.9 mm on seeds 0-2 but 23.1 mm median over 20 seeds; a 3-seed reading of 19.3 was logged as "double-peak optimism, lesson recurrence #4". The selection re-audit codified the sampling rule: "3-seed 的 swing 读数不可判点, 只能筛带,选点必须 20-seed" - 3 seeds may screen a band, only 20 seeds may pick a point.
Change
Swing (and any suspected multi-modal metric) reported as mode shares plus per-mode ranges instead of a bare median; 3-seed smoke numbers demoted to band-screening; all shipping/selection decisions moved to 20-seed batteries.
Outcome
The "swing debt" bookkeeping was reinterpreted as basin probability (see swing-bistability-damping-switch), and checkpoint selection stopped being whipsawed by which basin the first three seeds happened to fall into.
Mechanism
Central-tendency statistics presuppose unimodality; on a bimodal distribution the median tracks the mode SHARE, not any achievable behavior, and small samples alias the share entirely. Mode-aware reporting (share + per-mode stats) is the only faithful summary, and the needed sample size is set by the share resolution required.
Applies when
- a quality metric shows chronic high variance across seeds
- 3-seed smoke readings contradict 20-seed batteries
- reporting swing height, clearance, or any basin-prone metric
“中位数落在空档里,「swing 债 −11mm」实为「50% 概率掉进拖地吸引子」。历代 swing 高方差与 3-seed 不可判由此定性:一直在测双稳态系统。… swing 跨 seed 双峰 (500 在 seed0~2 只读 3.9mm, 20-seed 中位 23.1) —— 3-seed 的 swing 读数不可判点, 只能筛带, 选点必须 20-seed。”
train/README.md § swing 双稳态定性 / s1e 选点重审 No parameter tuning on the floor - a failing config retries once, then it is out; anomalies go back to sim
no-field-tuning-protocolHardware time is for executing and measuring the pre-registered matrix, never for tuning: failing configs get one retry then elimination, anomalies get recorded and reproduced in sim, and contract-check bypass flags stay unused.
Symptom
Hardware sessions create pressure to fix problems live - nudge a gain, tweak a scale - which destroys attribution and risks the robot.
Context
The anomaly-handling section of the acceptance sheet is three fixed plays: (1) falls at start -> retry once at the same settings; falls again -> that configuration is eliminated, "不现场调参" (no on-site parameter tuning); (2) limit cycle or motor screech -> stop immediately, record the gain level and the joint, reproduce in sim before any discussion; (3) systematic disagreement with sim -> record it as a finding (hardware outranks sim) rather than adjusting anything to force agreement. Related guardrails elsewhere in the sheet: never pass --allow-unstamped / --allow-plant-drift to bypass manifest checks - if it errors, something real is wrong, stop and look.
Change
Field sessions restricted to executing the pre-written matrix; every fix path routed through sim reproduction and the normal config/rung process.
Outcome
Sessions stayed interpretable (each run matched a documented config) and safety overrides never became habit; anomalies arrived back in sim as reproducible cases instead of half-remembered floor stories.
Mechanism
Field-tuned values are measured under adrenaline on one floor with no logging or baselines - they contaminate the config lineage and are unattributable afterwards; and every bypass flag that skips a contract check converts a designed safety property into an operator promise.
Applies when
- a config fails or oscillates during a hardware session
- someone reaches for a live gain tweak or a bypass flag
- writing the anomaly-handling section of a deployment runbook
“起步即摔 → 换档重试一次, 仍摔则该档出局, 不现场调参。出现极限环/啸叫 → 立刻停, 记录档位与关节, 回 sim 复现再议。… 不要给 --allow-unstamped / --allow-plant-drift —— 三枚 ONNX 都已盖章 … 真要报错说明有别的问题, 停下来看。”
train/REAL_RUN_S2.md § 4. 异常处置 A field experiment is allowed when it is pre-scripted, single-variable, and self-reversing (RAM-only writes)
reversible-single-variable-field-experimentsPermit hardware-side experiments only when scripted in advance with one variable, a log, and automatic reversion (volatile writes, git restore); keep every config mirror (yaml vs firmware) changed and restored as a unit.
Symptom
A hypothesis needed a hardware test - v5's "wild kicking" might trace to the RS00 torque cap being deployed at 11 N*m vs its trained 14 (-21%), on exactly the ankle-roll/hip-yaw joints doing lateral-yaw work - but changing limits in the field is the classic way to lose track of robot state.
Context
The experiment was written to be safe by construction: change exactly one number (robot.yaml RS00 tau_limit 11.0 -> 14.0), write to firmware RAM only (--write without --save, so a power cycle automatically rolls back to the saved 12/17/11), run the single logged trial, then restore both yaml (git checkout) and RAM immediately. The consistency requirement is explicit: the deploy tool's torque self-check compares against robot.yaml, so yaml and firmware must change and restore together; and the hypothesis scoping is itself single-variable - RS06's 67% cut was measured irrelevant (gait uses only 16% of rated) and hip torque was left alone for safety.
Change
Field experimentation policy refined: not "never touch hardware settings" but "only pre-scripted, one-variable, logged, auto-reverting changes with config/firmware kept consistent".
Outcome
The sub-experiment could answer the torque-cap hypothesis without any risk of the robot persisting in an undocumented state - forgetting to restore costs nothing but a git checkout.
Mechanism
The danger of field changes is state divergence (robot config drifting from the repo's record), not the change itself; volatile (RAM-only) writes bound the divergence lifetime to one power cycle, and single-variable scoping preserves attributability even in a field setting.
Applies when
- a hypothesis requires changing firmware limits or gains on the robot
- field debugging tempts persistent config writes
- designing safe escape hatches for deployment tooling
“程序(--write 不带 --save = 只写 RAM,断电自动回滚)… deploy 的限扭自检是对 robot.yaml 比对的,所以 yaml 和固件必须同改同还原;忘了还原也没事,断电重启即回 12/17/11(上次 --save 的值),但 yaml 要 git checkout。”
train/REAL_SWEEP_V5_V8.md § 4. 限扭子实验(可选二期,只对 v5,单变量) A suspended (no-load) test acquits or convicts the actuator before you blame authority
suspended-test-isolates-actuator-authorityBefore attributing a failure to actuator authority, measure no-load tracking error and steady-state torque fraction; blame authority only if the task fails while the error grows with demanded force - and then fix gains or targets, not training.
Symptom
hip_roll sagged 0.21 rad on the ground and saturation questions loomed over the sidewalk plan - was the roll axis physically too weak (authority), or was something else limiting it?
Context
Before C4, the roll-authority question was settled by measurement triage: suspended test (--suspend, feet off ground) showed hip_roll tracking error 0.0008 rad - actuator acquitted; the entire 0.21 rad ground sag is load-induced. Steady-state torque was 25% of limit - 75% margin remains. Since sidewalk needs lateral force, not exact angles, authority was ruled "not a hard limit", with a pre-registered criterion for when it WOULD become one: sidewalk fails to track AND roll error keeps growing - then the fix is raising hip_roll kp or lowering the vy target, not more training.
Change
Hypothesis "roll authority insufficient" demoted from blocker to a monitored branch with an explicit trigger condition; C4 proceeded.
Outcome
Later open-loop probes confirmed the actuator could produce the behavior (sidewalk feed-forward ran at full amplitude, 5/5 survival), and the eventual C4 failure causes were measurement and reward, never authority.
Mechanism
Suspended vs loaded comparison separates the actuator's closed-loop competence from the load path: tiny no-load tracking error means the motor/controller is fine and any loaded deviation is statics (gravity / stiffness budget, kp trading error for force). Torque-fraction measurement then bounds how much force headroom actually remains.
Applies when
- suspecting an axis is "too weak" for a new skill
- large position sag on a loaded joint
- deciding between hardware fix, gain change, and more training
“吊挂（--suspend）实测 hip_roll 跟踪误差 0.0008 rad → 执行器无罪，地面下垂 0.21 rad 全是负载所致；稳态占限扭 25% → 仍有 75% 扭矩余量。… 判据：若 C4 出现「侧走跟不动且 roll 误差继续变大」，那才是权限账 … 解法是提 hip_roll 的 kp 或降 vy 目标，不是硬训。”
train/C_LADDER_RUN.md § 3d. roll 权限：已部分澄清，不是硬上限 The recovery line's real-robot verdicts live in three places that disagree - the spec's "fairly stable, first real stand-up" for v2_6, an undated runbook note that only v3_1p1c works, and a first run whose details were never recorded
write-hardware-verdicts-backA hardware verdict is a dated entry in the authoritative ledger - policy file and stamp, gain profile, floor, battery, tries, log file, what was seen - written back the same day; a note in a command file is a pointer, not a verdict, and a newer verdict that contradicts an older one must say so.
Symptom
Asked "which recovery policy works on the real robot", the sources give different answers, and none of them carries the conditions of the test.
Context
08-09: the first real run was stopped as violent and dangerous; which ONNX, which gain profile and whether a log existed were marked "to be recorded" and never were. 08-11: v2_6 was "fairly stable", the line's first real get-up, with splits after standing; v2_5b's result and both CSVs were "to be reported". 08-14: v3_1p1c was stamped and pushed, with "the real first test still needs the user present"; the spec records no hardware result for it. The operator runbook (undated) puts above the v2_6 and v2_5b floor commands the note that none of the recovery policies below work, only recovery_v3_1p1c - a verdict never written back into the spec, with no date, floor, battery, number of tries or log attached.
Change
None recorded in the sources; this card records the gap.
Outcome
The line's authoritative record ends with v3_1p1c as the product awaiting its first real test, while the operator's note implies it is the only one that works and that v2_6 (recorded as a success) does not.
Mechanism
Verdicts given at the robot travel by word of mouth and command-file comments; without a record carrying the conditions, a later reader cannot tell a changed verdict from a changed floor, battery or stack.
Conflicts
§43 (2026-08-11) records v2_6 as the first successful real get-up ("fairly stable"); the undated runbook says every recovery policy except recovery_v3_1p1c does not work; §49 (2026-08-14) says v3_1p1c's first real test was still pending. The runbook's claim has no date and was never written back to the spec, so it cannot be ordered against §43.
Applies when
- choosing which policy to deploy from an operator's notes
- a hardware session ends without a written result
- two documents disagree about what worked on the robot
“下面的recovery都不行 只有recovery_v3_1p1c.onnx”
RL系统/FOLLOW THIS copy 2.md § #### Recovery Policy (operator runbook, undated) A joint-velocity penalty meant to slow the get-up cut joint speed 16% and left the get-up time unchanged - the knob never moved the variable, so the idea it was meant to test stayed untested
dof-vel-penalty-is-not-a-pacing-knobBefore reading a result as a test of an idea, check that the knob actually moved the independent variable; velocity regularizers smooth a schedule they do not set, and a schedule driven by per-step task income moves only when that income's time structure does.
Symptom
The get-up took 0.6-0.9 s in Isaac with large torque demand; the user proposed getting up more slowly so less torque would be needed.
Context
The idea had support in the accounts: the acceptance bound is an upper bound of 5 s (5-8x margin), the quasi-static squat path peaks at 25% of the limits, and rolling over needs no momentum. R3.2 raised dof_vel from -1e-3 to -5e-3 as the single variable.
Change
dof_vel -1e-3 -> -5e-3 (child-run from R3.1).
Outcome
Get-up medians moved +0.02-0.04 s (noise); raw joint velocity -16%; torque demand median got worse (hip_pitch 46-48% -> 63-67%) as the new term competed with torque_headroom on the same joints; MuJoCo 98 -> 96%. Verdict FAIL on the knob, not on the idea, and the rung was not adopted. When pace was later attacked through the income's time structure (V2.5/V2.5b), the MuJoCo get-up moved into the 3.5-4.5 s design band.
Mechanism
The pace was set by base_height_progress paying for every step spent high (stand earlier, earn more); a velocity regularizer only smooths motion along the same schedule and does not change when the robot stands up.
Applies when
- trying to make a skill slower or gentler with smoothness penalties
- an experiment's primary metric did not move and a verdict is being written
- two penalties act on the same joints
“**关键判读:`dof_vel` 罚只把关节速度压了 16%,而起身用时一点没变。** 也就是说**这一级根本没有把"慢下来"这个自变量推动起来** —— 所以它**不构成对 用户假说的检验** … 起身节奏由 `base_height_progress` 的逐步计酬决定(早站起来就多 拿),速度正则只在同一条时间轨迹上把动作抹匀,不改变何时站起来。”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §25 R3.2(dof_vel −1e-3→−5e-3,慢一点起身) FK-verify a borrowed reference's structure, then size its amplitude by the reference's job - it pins phase, the policy adds lift
reference-structure-fk-amplitude-divisionWhen borrowing a reference trajectory: verify its structural claim against your own kinematics (an invariant like flat-foot), assign it the phase-pinning job, and size amplitude low enough that the policy contributes the lift - moving toward a proven foreign value in halves, not jumps.
Symptom
walk_v4 had big knee swing (40-46 deg) but only 18-24 mm foot lift - amplitude without hip/knee/ankle phase coordination; later, walk_v5's real-robot swing ballooned to 73.6 deg (sim 55.7) with violent footfalls - amplitude over-driven by the reference.
Context
Structure first: Humanoid-Gym's 1:2:1 hip:knee:ankle reference was verified on the local model before adoption - the ratio exactly satisfies the locally derived flat-foot constraint hip - knee + ankle = 0, FK-tested at multiple amplitudes with sole pitch 0.00 deg throughout. Amplitude second, and here the first reasoning failed honestly: FK said shorter legs need LARGER reference scale (0.30 for 30 mm lift), and the FK was correct - but the premise was wrong ("FK 没错, 但前提错了"): it assumed foot lift must come from the reference. HighTorque Pi, same scale, uses 0.08 with a 0.02 m foot-height target - proof that lift is added by the policy ON TOP of the reference, whose actual job is pinning the phase relationship. Scale 0.30 made the reference the entire gait: over-constrained and over-driven. The correction went to 0.15, deliberately not Pi's 0.08: "一次只走一半, 留退路" (walk half the distance, keep a retreat).
Change
target_joint_pos_scale 0.30 -> 0.15 as one of v6-minimal's three changes, treating both the footfall force and the lateral kicking (yaw momentum scales with leg swing amplitude).
Outcome
v6 improved landing force 1.72x -> 1.55x, suspended tilt 45.9 -> 23.0 deg, turn-gain asymmetry 70% -> 19%; the later v6-halved-shaping experiment (35 mm -> 4 mm collapse) confirmed the reference still carries the gait's existence on this machine - the division of labor is real but machine-specific.
Mechanism
A joint-space reference plays two separable roles: encoding structure (phase relations that keep the foot flat) and injecting amplitude (energy). Structure transfers across robots and is checkable by FK against an invariant; amplitude is a negotiation with the policy, and over-assigning it to the reference removes the policy's freedom to modulate lift with state.
Applies when
- importing a reference gait / imitation target from another codebase
- reference amplitude reasoning based on leg length alone
- real swing amplitude far exceeds sim's under a strong reference
“FK 没错, 但前提错了。我默认抬脚必须由参考轨迹产生。HighTorque Pi 同尺度机器人 … 用 0.08, 而它 target_feet_height = 0.02 m —— 说明抬脚是策略在参考之上加出来的, 参考只负责钉住髋/膝/踝的相位配合。我们取 0.30 等于让参考本身就是整个步态, 过约束 + 过驱动”
train/WALK_V6_MINIMAL.md § ① target_joint_pos_scale 0.30 → 0.15 Every new penalty ships with a pre-registered withdrawal clause - if healthy gait must pay above the cap, the term stands down
calibration-threshold-with-withdrawal-clauseIntroduce every new penalty with: the zero-cost-option audit, a replay-calibrated weight formula (healthy pays a fixed small fraction of tracking), and a pre-registered withdrawal condition - and let the clause fire without argument when the calibration says the term cannot be afforded.
Symptom
Three same-shaped crashes had established a failure archetype: v4's clearance, v8a's landing window (weight off by 58x uncalibrated), and v6a's bare hip_yaw suppression all combined a zero-cost "don't move" option with a fee on any motion - a reverse barrier that pushes policies toward standing still.
Context
The v11 landing-window penalty was therefore introduced under a calibration-threshold protocol: (1) shape chosen with the window tightened (h_gate 0.03 -> 0.02, because 0.03 equaled the clearance target and priced the entire descent); (2) weight from a FORMULA, not judgment: measure the term's raw value on healthy replays (v5/v10b), set w = -(0.10-0.15 x tracking reward) / raw_healthy; (3) withdrawal clause pre-registered: if healthy gait must pay >15% of tracking no matter the tuning, the term is withdrawn to the next version rather than forced in - "不硬上". The companion hip_yaw quieting term ran the same protocol (calibrate on replays, healthy pays <=5%) and was later retired entirely when a structural fix (zero action scale) made its shaping tax unnecessary.
Change
Penalty introduction protocol: shape audit (what is the zero-cost option?), replay-based weight formula, healthy-pay cap with a written stand-down condition - all before training.
Outcome
The landing term was in fact withdrawn under its clause (v12 records "P5 落地窗口罚 已撤 … 维持撤下"), demonstrating the protocol firing as designed instead of the fourth same-type crash.
Mechanism
A penalty's damage mode is mispricing healthy behavior; since the healthy price is measurable in advance on replays, both the weight and the go/no-go decision can be computed rather than discovered by a ruined training run. The withdrawal clause converts "make it work" pressure into a clean deferral.
Applies when
- adding any motion-taxing penalty to a working gait
- a proposed term's weight has no measurement behind it
- a previous same-shaped term crashed training
“权重公式而非拍脑袋:先在 v5/v10b 回放上量 h_gate=0.02 的原始值,w = −(0.10~0.15 × 跟踪奖励) / raw_健康;标定门槛:若健康步态无论如何要付 >15% 跟踪,本项撤下留 v12,不硬上 (v4 clearance/v8a-B/v6a 三次同型翻车的教训:代价为零的"不动"选项 + 一动就收费 = 反向壁垒)。”
train/WALK_V11_SPEC.md § 6. P5 —— 落地窗口罚(三代欠账,标定门槛制) Exponential tracking kernels go flat exactly when the error is largest - pair them with an L2 term for the far field
exp-kernel-needs-l2-far-fieldNever let an exp/Gaussian kernel be the only tracking pressure on a quantity that can drift far from target: pair it with an unbounded (L2) term sized as the "don't diverge" floor, and check which frame the kernel reads.
Symptom
With only an exp-type yaw tracking term (exp(-err/std^2), std 0.25), a robot whose heading had drifted badly received almost no corrective gradient: at error 0.6 rad/s the term evaluates to exp(-0.36/0.0625) = 0.003 - near zero AND flat.
Context
The exp kernel is excellent for fine tracking near zero error but its gradient vanishes at large error - precisely when correction matters most. Fix: add track_ang_vel_z_err_l2 (-0.5), a plain quadratic on the same quantity: "exp 管精细跟踪、L2 管'别发散', 互补". Both terms deliberately read WORLD-frame wz (matching the exp term's source), because this torso sways enough that body-frame wz means are systematically off (measured -0.039 while actually turning +0.152). The same far-field-gradient argument reappears in the v8 risk list: frozen joints could not climb back because their huge error put them on the exp plateau ("远端梯度消失是冻结自锁的帮凶").
Change
Added the L2 companion term at -0.5 alongside the existing exp term (a term that had been in an earlier draft and was lost in a rewrite - itself worth noticing).
Outcome
Corrective pressure restored across the whole error range; the exp+L2 pairing became the house pattern for tracking terms.
Mechanism
d/de[exp(-e^2/s^2)] -> 0 as e grows: the kernel saturates and cannot distinguish bad from terrible. A quadratic's gradient grows with error, covering the far field; summing the two yields monotone corrective pressure with fine shaping near the target.
Applies when
- tracking rewards use exp/Gaussian kernels alone
- a drifted or frozen state fails to recover during training
- designing tracking terms for quantities with large transient errors
“exp 在误差大时梯度趋零, 恰好在最需要纠正的时候失灵。… 误差 0.6 → exp(-0.36/0.0625) = 0.003, 接近零且平坦。… exp 管精细跟踪、L2 管"别发散", 互补。”
train/WALK_V7_SPEC.md § ② track_ang_vel_z_err_l2 −0.5 —— 补 exp 的梯度洞 One fixed acceptance matrix for every rung - new skill must PASS while every old skill stays within a regression budget
fixed-acceptance-matrix-per-rungFreeze one acceptance matrix for the whole ladder; every promotion requires the new skill's PASS plus bounded regression on every prior skill, measured against the parent's baseline under the current (bug- fixed) metric code - and include command transitions, not just steady states.
Symptom
Sequential skill training silently trades old skills for new ones (C1 trained away the root's backward ability); without a constant measurement frame, each rung's numbers are incomparable and regressions hide.
Context
The C ladder ran the same 13-cell command matrix at 20 seeds per cell at every rung (stand; vx +0.15/+0.30; vx -0.10/-0.20; vy +/-0.10; wz +/-0.20; two vx&wz combos; two vx&vy combos), with promotion requiring "新技能 PASS 且旧技能不明显退化" - old-skill regression budget <=2/20 against the parent's recorded 20-seed baseline. For the transition-rich final rung, a command-switch block was added (forward->stop, stop->backward, forward->turn, left->right, turn->forward; survival + re-track within 2 s) because "每个 steady command 都会做 ≠ 命令切换不会摔" - steady-state success does not imply switch safety, and the joystick does switches. The C4 product's gate ran 260 cells (13 x 20) all 20/20.
Change
Battery frozen once, reused verbatim per rung; baselines re-measured per parent (and re-measured again after the metric-frame fix, since old baselines were taken with the buggy coordinate reading - "旧基线是坏坐标系的， 不可引用").
Outcome
Regressions were caught at the rung that caused them (C1's backward loss, C2's vx+0.30 decay), and cross-rung comparisons stayed valid for the ladder's whole life.
Mechanism
A constant matrix makes every rung's output a point in the same metric space, so "did we lose anything" is a table diff, not a judgment call; the per-skill regression budget converts previously earned PASSes into standing constraints on all future training.
Applies when
- designing gates for sequential skill addition
- promoting a checkpoint to be the next rung's root
- after any evaluation-code fix (old baselines must be re-measured)
“新技能 PASS 且旧技能不明显退化才晋级。… C5 追加：命令切换验收（steady ≠ transition） forward→stop、stop→backward、forward→turn、left→right、turn→forward，各 20 seed，判存活 + 切换后 2 s 内是否重新跟上。”
train/C_LADDER_RUN.md § 5. 固定验收矩阵（每级跑同一张，每项 20 seed） Curriculum-gate a penalty to the phase where its disease occurs - early on it only taxes exploration
gate-penalties-to-the-disease-phaseFor penalties aimed at late-stage pathologies (freezing, saturation, degenerate attractors), ramp the weight in only after exploration noise has decayed; anchor the terminal weight to measured healthy-vs-sick raw values, and shift all related tripwires to after the ramp completes.
Symptom
The action_saturation penalty, applied from iteration 0 in v8a, taxed exploration itself: with init_noise_std 1.2 the sampled actions paid ~-2.45/step before any policy had formed - while the disease it targets (clamp freezing) is a LATE pathology (v9 froze at iteration ~2624).
Context
v10 re-introduced the same penalty behind a curriculum gate: weight 0 until iter 1000, ramping linearly to -1.0 by iter 2000 - present only when the disease can occur, absent while exploration noise dominates. The trust argument was evidence, not hope: in v8a the term, while active, had pulled joint_pos_ref from 0.041 up to 0.155 and climbing - proof it can extract a policy from the frozen pit. Weight magnitudes were anchored to measured raw values (healthy v5 0.310 / v6 0.106 vs frozen v7 1.145 / v9 1.22 per step: at -1.0 healthy pays 6-18% of tracking, frozen pays 60%+, standing ~0). v10c then isolated the gated term as THE anti-freeze mechanism by single variable, upgraded to untouchable status in v11: "S 的门控机制(v10c 单变量铁案:任何情况下 不许撤,只许调终值)" - and v11 dared to relax other penalties only because S stood guard.
Change
action_saturation gated 0 -> -1.0 over iters 1000-2000 (later terminal value tuned -1.0 -> -0.5 with the gate mechanism itself frozen); tripwires adjusted to respect the gate's timing (freeze check moved to iter 2500-3000 to give the ramped term its effect window).
Outcome
Freezing stopped recurring while early training kept full exploration; the mechanism graduated from experiment to invariant within two versions.
Mechanism
A penalty's incidence depends on who occupies its support: early in training that is exploration noise (whose suppression starves learning), late it is the converged pathology. Time-gating aligns the penalty's presence with its target's presence, buying the constraint without the exploration tax - and tripwire timing must then be computed from the gate schedule, not from ungated precedents.
Applies when
- a structural penalty punishes exploration in early training
- a late-onset pathology (freeze/saturation) needs a standing guard
- deciding when a curriculum ramp should engage
“v8a 实锤它的病根是"罚在采样动作上"——init_noise_std 1.2 的早期等于罚探索(~−2.45/步);而冻结是晚期病(v9 速率 2624 才死平)… 门控让它只在病发期在场。… v8a 里它在场时 joint_pos_ref 从 0.041 爬到 0.155 且仍在升——有从低谷爬出的实证。”
train/WALK_V10_SPEC.md § 2. S 保险 —— action_saturation 课程门控 Fall recovery was defined as the whole chain - any fallen pose, a stable stand, a clean hand-back to walking - and built as a second policy behind a deploy-side switch, not folded into the walking PPO
recovery-two-policies-and-a-state-machineDefine a recovery skill by the whole chain it must complete, including the hand-back to the next controller; if it is built as a separate policy, make the switching logic and its handoff contract a deliverable of their own, and keep the recovery observation contract a subset of the locomotion one so a unified policy stays possible later.
Symptom
A walking robot that falls needs a human to stand it back up. The design question on 2026-08-09 was whether to teach getting up inside the existing omni walking policy or beside it.
Context
The user set the goal as "any fallen pose -> stand up alone -> stand stably", and the spec named the real difficulty as the full chain fall -> recovery -> stable stand -> correctly initialised walking history and clock -> walking, making the deploy state machine a first-class deliverable. A unified single policy had a real-robot precedent (arXiv:2605.18611, a state-dependent gate near 37 deg tilt) but was deferred until a recovery policy and an omni policy were each reliable. The line ran on its own branch and worktree with every walk/stand/omni/run config path untouched. The development path copied the G1 learned get-up logic (arXiv:2502.12152): first find any feasible get-up (ugly accepted), then add smoothing, torque and real-robot constraints. The recovery contract kept the base 45-dim observation (command slice held at 0, no gait phase, no frame history - their reasons do not apply to a skill without a clock or a velocity task), so it stays a prefix of the 215-dim omni contract and a later merge is not foreclosed.
Change
Two policies and a deploy-side switch instead of one retrained walking policy; recovery got its own minimal contract (45 dims, full-range action, later the beta-anchored profile) and its own acceptance battery.
Outcome
The split held for the whole line: on 08-14 deploy_policy gained a second (PolicyIO, ONNX) pair behind --recovery-policy, each loaded under its own manifest contract, and the runbook runs stand_v1b or omni_c4_ff800 as the locomotion side with recovery_v3_1p1c. The literature scan of 08-10 found that every verified get-up implementation deploys one end-to-end policy (or softly gated experts) and stages only on the training side - so the runtime state machine here is the walk/recovery switch, not a staged get-up.
Mechanism
A separate policy keeps each reward table single-purpose and lets a proven walking lineage stay byte-frozen; the cost moves to the handoff, where every piece of state one policy leaves behind (history, clock, last action, command) must be reset for the other.
Applies when
- adding fall recovery or get-up to a robot that already walks
- choosing between one unified policy and a switched pair of policies
- designing the observation/action contract of a secondary skill
“先做 recovery policy + omni policy 两个策略,部署侧状态机切换;不把 recovery 硬塞进现有 omni PPO。 … 任务定义:**任意跌倒姿态 → 自己站起来 → 稳定站立**。真正的难点不只是"起身", … omni walk**(§6 部署状态机是本 spec 的一等公民,不是附录)”
git:Lucen-recovery@origin/recovery:train/RECOVERY_V0_SPEC.md § §0 目标口径与架构判决(用户 2026-08-09 定)